It would be awesome to use that outer clamshell bracket attached to a hoist to lift and store the rear roof section out of the way in the garage.

The 2-door Bronco install is a little vague. Would be nice if you could do a quick video for that. The front clamps are not as obvious because the front of top doesn’t have the factory cut-outs that the back does. The JCR roof rack is very nice btw.

@Mpatient1

Жыл бұрын

especially if only doing short rack since it says install the front and rear mounts before the mid mounts...

Do you have a list of validated (or recommended) 40" lightbars for the cutout?

@JcrOffroad

Жыл бұрын

We recommend the Baja Designs S8 40" but any bar that fits these specs should work. Cutout fairing designed for 41.25" max lens housing width single row LED light bar. Up to 43.5" (mounting stud width) bar will fit with our mounts, but trimming of the fairing will be required

Air saw sounds like someone with really bad gas!!! LOL

Thanks for the video. How high is the highest point on the rack above the hardtop?

@JcrOffroad

Жыл бұрын

About 3.5" - 3.75" above the center of the hardtop.

I’m considering this for my bronco. What is the static and dynamic load rating for the 2 door rack you sell? Thanks.

@JcrOffroad

Жыл бұрын

Dynamic (road) weight rating is 120lbs evenly distributed. Static and jarring off-road weight limits are at your discretion.

Safe to assume the front roof panels can't be removed with this rack installed?

@JcrOffroad

Жыл бұрын

They can be actually.

@theliberator9913

Жыл бұрын

@@JcrOffroad that's awesome!

Hello guys. I recently installed the full size roof rack on my bronco. Even though the steps are simple... I ran to a lot of issues of the bolt holes not aligning or large clearances where the bolts would not cross over for proper engagement. This resulted in a using brute force on several occasions. Many attempts were made at calling your technical department with no success; over 30 minutes waiting for someone to not answer. Hopefully I can get an answer here for my following questions. I have noticed the rack makes a lot of noise (not wind noise) when the vehicle is moving, more pronounced in the back and going through bumps on the road. Cant really describe the sound without a video which I can easily provide. Is this normal?

@JcrOffroad

Жыл бұрын

Sorry to hear you had issues getting a hold of us. If you could please email info@jcroffroad.com, we could certainly help you with tech support on the installation!

@427motorsportllc3

Жыл бұрын

@@JcrOffroad Why don't you answer his question on here so we all know what the answer is? Or is it too difficult for you all, just like it's too difficult to actually send the mounting pieces with the foam already installed...or is paying $1000 for a few pieces of aluminum not enough for you to engage in activity that seems beneath you?

@JcrOffroad

Жыл бұрын

@@427motorsportllc3 because the people that reply to these comments on KZread are not the same people that provide tech support. We also have a support ticket system to keep track of any issues, not only for customers like Eduardo, but for any future customers that may have the same issues. If we can help you with anything tech support related, feel free to contact our customer service team as well using the form at www.jcroffroad.com/CTUS.html

@f100

Жыл бұрын

Update: The noise is not related to the roof rack. Simple coincidence it happened at the same time of the installation. To clarify, it's a very good quality roof rack.

@Victory4x4

Жыл бұрын

@@f100 Thanks for the update Eduardo

And what can you put on this roof rack…?

@JcrOffroad

2 ай бұрын

Roof top tent, awning, recovery gear, storage boxes, etc.