No video
Broken Ford C-Max Torque Engine Mount - $40 DIY Fix
Tonight I replaced my Ford C-Max Torque Engine Mount which is located at the bottom center behind the underbody plastic. This is doable with some basic tools and a bit of technique which I'll show you.
Links to parts and tools used:
Engine mount: amzn.to/3d3NCLe
Tools Used:
Ratcheting Wrenches: amzn.to/3D5uebs
Breaker Bar: amzn.to/316JFTr
Torque Wrench: amzn.to/3xCQto3
Chapters:
Intro - 0:00
Removal - 2:55
Old vs. New - 10:25
Reassembly - 10:44
Conclusion - 14:49
The affiliate links above give me a small commission for recommending the products to you. It doesn't cost you a dime to use these, but it is a great way to support the channel and I really appreciate the support!
Dan
Пікірлер: 42
Thanks again for saving me thousands of dollars in repairs!
@DansWay
29 күн бұрын
I’m glad this was so helpful!
Thanks for the vid! my Grandfather taught me that wrench trick :)
@DansWay
3 ай бұрын
I just had to use it to get the oil drain plug off a C-Max where there isn't space for a socket wrench. Love knowing neet tricks like this.
Your channel should be sponsored by Ford!
@DansWay
29 күн бұрын
Yah but then they couldn’t charge people so much to repair these problems! 😉
@marcosramos4596
29 күн бұрын
@@DansWay here in California the Ford Dealerships are not owned by Ford!
This was great and highly helpful. Will the oil change video see the light of day? Thanks for sharing!
@DansWay
Жыл бұрын
Hey David, thanks for the comment. We drive with the gas engine so little I'm not sure when I'll need to do that anytime soon honestly! We are currently sitting at 80MPG because most of our driving is within 15-20 miles...
Great video
im in england just about to replace this part a great video very useful so thank you
@catchcarpcarter
9 ай бұрын
just done it only dofferemce is we dont have the rear awkward bolt on the back so its alot easir to do but the video was a great help to know what i needed
Where are the other engine mounts located? Thanks if you could point them out
@DansWay
2 жыл бұрын
Honestly I’ve looked and couldn’t really see the one behind the motor drive. With the lower mount removed (or broken like mine) you can easily rock the engine back and forth which helps to show where the engine is pivoting.
@georgeselby3376
4 ай бұрын
One on either side of the engine bay, the engine hangs from them. The passenger side one is hydraulic and can leak fluid, it's near the coolant degas reservoir, the transmission (driver's side) one is under the transmission computer (TCU.)
I brought my CMAX to the dealer, it got 22-2396 error code according to the dealer. But they never checked Engine Mount, but replaced fuel system drier, brake flui, spark plugs, installed air cleaner, frigi charge, and mass air flow sensor cleaner which I do not believe contributed to the origin of the problem.
@boatx22
6 ай бұрын
Typical ford dealership haha
This looks quite difficult to do at home.
I suspect this is what happened to my 2014 CMAX. it started making noise when I drive especially in low speed. The entire car shakes
@joanne4449
Жыл бұрын
I spent almost $3000 at the James Ford dealer in half moon bay. They didn’t even figure out what is the problem but suspect it’s transmission issues
How many hours labor was it?
@DansWay
Жыл бұрын
It shouldn't take more than two hours start to finish for this one part.
@906lane
Жыл бұрын
start to finish took me 1 hour 30 mins
I don’t see the link for this part
@davidellis5868
8 ай бұрын
I found it
You also need to replace the upper tranny mount or else it breaks the lower one too
@DansWay
2 жыл бұрын
Yah, that one is good for now. Looks to be more involved to remove. Have you done this?
@apostolllos
2 жыл бұрын
@@DansWay I haven’t I only replaced the one you showed and turns out car still shakes and it’s because of the upper transmission mount + motor mount because they both degrade at the same time and it’s harder and more expensive to replace
@kevinthacker8349
2 жыл бұрын
If you do all the mounts at the same time , you save having to remove the hard to get to blot and in long run will same time on the repair When mount has gone it will but more strain on the others
@apostolllos
2 жыл бұрын
@@kevinthacker8349 mine needs to have most of the mounts replaced but i dont feel like its worth doing since its a salvage car which i’ll sell in less than a year
@DansWay
2 жыл бұрын
Anyone have a link to directions on replacing these upper mounts? The one on the driver side seems really difficult to get to.
My car may have similar problem. I noticed similar noise when braking in D and R. Did you also experience any clunk or rattle over large bumps? Here is video of the movement I'm seeing. I wasn't able to move the rear transmission mount by hand easily like you are able. kzread.info/dash/bejne/aqKNy6iBY7u_fbg.html Did it fix the noise you hear while braking?
@DansWay
Жыл бұрын
Hey nice video. I'm not sure the movement there is abnormal at all. I don't recognize the clucking noise myself. Do you hear this noise when just rolling over speed-bumps, or perhaps when dropping off a small ledge (driveway to dirt). I've had bad sway-bar bushings cause a clunking that took a while to figure out. Struts were fine, but bushings where allowing bar to move up-down 1/8" creating a clunk.
@chrisx742
Жыл бұрын
@@DansWay Yes, over steep speed bumps, small ledges, potholes I hear a clunking in the CMAX. Did you have that issue in your CMAX, or in another car? When I replaced the lower control arms on my CMAX I pryed on the sway bar and didn't see any movement in the bushings, although that doesn't mean there isn't any.
@DansWay
Жыл бұрын
@@chrisx742 I was working on a Camry, but similarly I couldn't figure out how to see the issue. I pushed and pulled and couldn't get visibility on the problem. If you jack up the car so that both front tires are off the ground, then put a pri-bar under the bar just next to the bushing you might get some movement. I haven't replaced them on my C-Max. You might also try rocking the car back/forth really hard to get the bar to transition from push/pull on either side to see if you can replicate the noise. Let us know what you find!
@chrisx742
Жыл бұрын
@@DansWay Another question, if you don't mind. The noise might be from my steering rack or tie rods. The problem is, when I attempt to diagnose by jacking the vehicle and pushing/pulling at 9 and 3, the steering wheel also moves. Everything I have read says that the steering rack typically stays in place, but on mine, it moves when I shake the wheels, which makes it difficult to diagnose a loose tie rod. Does your steering wheel move when you push/pull on the wheels? (just need to jack up one front corner to test.) This would help me to know if there is a problem with my steering rack.
@DansWay
Жыл бұрын
@@chrisx742 when you mean move, do you mean wiggle, or fully rotate?