Great tutorial. I love how you put grease on every gasket; it is something my father taught me when I was little, and I have never seen any other KZreadr do it. You should have indicated that you used a lapping compound on the valves.
@d.b.t.1696 Жыл бұрын
I was feeling a bit panicked the further you got. I'm pretty sure I would have forgotten what goes where. You handled it like a pro. Awesome video!
@pkf4124 Жыл бұрын
This is like a how to video. Great because my little one has expressed interest in engines and a Brigs Stratton engine is the purfect thing to start him on. Thanks for sharing.
@tonyburke12472 жыл бұрын
Great job but if you spoke and explained to people who don't understand great job 👏
@keshoreramadin5595 Жыл бұрын
Great restoration
@simonallan99413 ай бұрын
How do you properly restore one of these when you can't even replace the pistons rings? they have an aluminum bore and are thrown out once the cylinder gets too worn.
@fixitorstripitGardenmachines2 жыл бұрын
looks mint great job
@LawnMowersThingsThatMakeNoiseАй бұрын
Excellent video. i will follow it myself when i restore a couple of my mower engines. Did you clean out the carb thoroughly ? by removing the jet where the silver gauze is and clean through it. the air filter that you have used is the incorrect type it needs to be the green version with a sealing lip "272235S"
@ninazeng60362 жыл бұрын
Nice job!
@tinkeringtaylor30532 жыл бұрын
Great job done looking forward to part 2
@valartools8612
2 жыл бұрын
Thank you
@Kamaz40rus
Жыл бұрын
@@valartools8612 Hi. What kind of sealant was used for the gasket. Silicone or anaerobic?
@hepeng2627 Жыл бұрын
thanks share this video
@brunorault60456 ай бұрын
bon travail
@bubydrumm3 ай бұрын
Svaka ti čast, pa ovo danas niko ne radi, ruke ti se pozlatile 🙏 Jel može neko kontakt ako si u Srbiji?
@Torin_Hrastostit Жыл бұрын
Hello, great video! I would really appreciate it if you could tell me something. My Briggs & Sttraton is same as yours. However, it has one problem. It uses oil more than it should and white smoke always appears. What should I do? Thanks in advance!
@Trackhoe0752 жыл бұрын
Would of been to see it run
@MANUEL16X3 ай бұрын
What do you use to lubricate the seals?
@nemanjalevnajic21942 жыл бұрын
Alal ti vera majstore
@valartools8612
2 жыл бұрын
Hvala😀
@ninazeng60362 жыл бұрын
【from HIPA】are you interested in testing my parts for your machines?
@dinhcao75282 жыл бұрын
At 00:53:30 What is the torque settings for the head gasket?
@rawux1228
2 жыл бұрын
Just torque it with your hand and u will be ok
@dinhcao7528
2 жыл бұрын
@@rawux1228 thanks
@georgeclarke6151
Жыл бұрын
Great instructional video brother close up filming first class
Пікірлер: 26
Great tutorial. I love how you put grease on every gasket; it is something my father taught me when I was little, and I have never seen any other KZreadr do it. You should have indicated that you used a lapping compound on the valves.
I was feeling a bit panicked the further you got. I'm pretty sure I would have forgotten what goes where. You handled it like a pro. Awesome video!
This is like a how to video. Great because my little one has expressed interest in engines and a Brigs Stratton engine is the purfect thing to start him on. Thanks for sharing.
Great job but if you spoke and explained to people who don't understand great job 👏
Great restoration
How do you properly restore one of these when you can't even replace the pistons rings? they have an aluminum bore and are thrown out once the cylinder gets too worn.
looks mint great job
Excellent video. i will follow it myself when i restore a couple of my mower engines. Did you clean out the carb thoroughly ? by removing the jet where the silver gauze is and clean through it. the air filter that you have used is the incorrect type it needs to be the green version with a sealing lip "272235S"
Nice job!
Great job done looking forward to part 2
@valartools8612
2 жыл бұрын
Thank you
@Kamaz40rus
Жыл бұрын
@@valartools8612 Hi. What kind of sealant was used for the gasket. Silicone or anaerobic?
thanks share this video
bon travail
Svaka ti čast, pa ovo danas niko ne radi, ruke ti se pozlatile 🙏 Jel može neko kontakt ako si u Srbiji?
Hello, great video! I would really appreciate it if you could tell me something. My Briggs & Sttraton is same as yours. However, it has one problem. It uses oil more than it should and white smoke always appears. What should I do? Thanks in advance!
Would of been to see it run
What do you use to lubricate the seals?
Alal ti vera majstore
@valartools8612
2 жыл бұрын
Hvala😀
【from HIPA】are you interested in testing my parts for your machines?
At 00:53:30 What is the torque settings for the head gasket?
@rawux1228
2 жыл бұрын
Just torque it with your hand and u will be ok
@dinhcao7528
2 жыл бұрын
@@rawux1228 thanks
@georgeclarke6151
Жыл бұрын
Great instructional video brother close up filming first class
Looks like too much oil.