Nice and clean 💪

First lesson my carpentry teacher taught us over 40 years ago is to keep your fingers together when handling timber on any machinery, so you know where they are. Sooner or later a blade or knives will grab one of those sticky-out bits. They don't grow back.

@ian1352

Жыл бұрын

Mine are always near my hand, so I always know where they are.

faina fierastraul maestre. dar mai fain e al meu 😜

💪💪💪how deep it cuts

@ToolTest

2 жыл бұрын

70 x 270 mm at 0°

Does this machine have depth stop

@ToolTest

Жыл бұрын

Yes

so it's not only mine that make this strange noise when it start!

Is there at least a light on this saw?

@kiwigrunt330

Жыл бұрын

No. But it is a light saw.

@bromarvids5186

Жыл бұрын

@@kiwigrunt330 ha ha. Fair enough. I bought one regardless. But I just wish there was a light on it.

This test is only if you want to saw with precision, with a miter saw.(test is not intended for rough and hardwork). Tips and Test: Very important if you would like to saw with precision. (avoid torsion as much as possible)! Always choose a Miter saw with a handle positioned in a vertical line above the saw blade. Everything must be aligned, slide rails, handle, and saw blade,it is much better this way the blade will not tilt. Because there is some torsion in the aluminum housing . And choose an engine with softstart on it to prevent wear of the gear and worm shaft. It is very important that everything is aligned. Here are some examples to show how the handle must be positioned above the blade. Bosch gcm 800 sj / Bosch gcm 8 sjl / Evolution rage 3 / FESTOOL KS 60 / HITACHI C12RSH2 / FESTOOL KS 60 E KAPEX / Metabo KGSV 72 Xact (This also is the case with the Miter saw without the slide rails). If you want you can test it yourself at home if there is torsion in the aluminum housing. Step-1. First you make a saw cut from +-5 mm deep in to a flat piece of wood about +- 20 mm thick to this with the normal handle positioned on the right side of the Miter saw (the wood it will remain in place until the test is completed). Step-2. Then repeat this by pushing the saw blade down with your hand (finger) on the aluminum protective cover were the saw blade is cased in. Just now only do this without the running engine. Step-3. Now you can see if the saw blade will be positioned in or next to the saw cut. If the saw blade is (+- 0,2 / 0,5 mm) next to the saw cut then there is torsion in the aluminum housing (test is completed). Step-5. When you measure the vertical 90 degrees angle square (Digital Level Box) of you're sawblade don't forget that there is always some torsion in the aluminum housing. Conclusion:how further away the handle is from the saw blade how more chance of torsion in the aluminum housing don't go for that (the choices are yours). Also with a cheap slide miter saw it is still better the handgriff in line a above the saw blade than on the right side. Maybe they will make it someday then we have a winner...

ieiii.... nici tu nu il folosesti corect 🤣🤣, tre sa astepti sa se opreasca panza si apoi sa ridici.. nici mie nu imi iese 😜😜

@DemoToolsYT

2 жыл бұрын

Dorm langa el daca astept de fiecare data sa se opreasca panza de tot 😂 Mai nasol este ca la ridicare, mai ia un pic din material 😀

@floreamihai.

2 жыл бұрын

@@DemoToolsYT m-am uitat maestre.. n-ai asteptat nici o data 🤣🤣

@floreamihai.

2 жыл бұрын

@@DemoToolsYT dupa faza cu animalul ala cu coarne trebuia sa te prind la cotitura 😝

@DemoToolsYT

2 жыл бұрын

@@floreamihai. 😂😂

@DemoToolsYT

2 жыл бұрын

@@floreamihai. Ba maestre, dar ma jur ca poza aia n-avea niciun apropo spre tine si circularul Bosch 😂