In this DIY tutorial, I show you how to replace the bevel gear and the pinion of your GWS 6-115 angle grinder from Bosch.
Жүктеу.....
Пікірлер: 24
@atexc56042 жыл бұрын
Great way to destroy your axle(just like you did :P). If you have bearing separator AND bearing puller then just simply hook puler to the separator. If you have only separator just clamp it like you did and then use 2 screws, and ~10mm steel bar to push the axle. Separator have 2 vertical holes, one on each side - use as large screws as possible. You need to drill 2 holes in steel bar in correct distance to push that axle. If you don't have separator / puller you can use long socket and hammer, but please use at least copper coin on top of axle to not destroy it like on this video.
@LuisGomez-vu6wg2 ай бұрын
Muchas gracias por el video es de gran ayuda Dios lo vendiga
@renatoarrighi56373 жыл бұрын
many thanks for your help. now I can repair mine with same problem. thank you so much- renato Italy
@cyberbunny100
2 жыл бұрын
You are welcome.
@samuelfabio700219 күн бұрын
Ok! Muito bom mesmo! Valeu 👍👍
@diymaster1018 ай бұрын
Thanks so much it worked 👍🏾
@greenpanda843 жыл бұрын
Thanks Man!
@user-lk2cs3ts1b Жыл бұрын
Техника ,на высоком уровне разборки ушм блогадарю, учус.
@robertobezerra83762 жыл бұрын
Ótimo trabalho parabéns 👍👍
@cyberbunny100
2 жыл бұрын
Muito obrigado.
@blablablabla99203 жыл бұрын
Super Job , ich hab ein PWS 620 , das was Sie repariert haben , ich meine die Kugellager ist defekt die mit Getribe (abstands metal ist kaputt und die kugellagern die bleiben alle zusammen .
@ezrika02573 жыл бұрын
the gear housing, can fix other brand ?
@horiachiorean85923 жыл бұрын
You need to put a little more grease
@cyberbunny100
3 жыл бұрын
Thanks for the tip.
@ezrika02573 жыл бұрын
can use any type of greese oil ?
@cyberbunny100
3 жыл бұрын
No, a special grease is specified in the operating instructions.
@DanielMartinez-sw5bz4 ай бұрын
Destruido el eje por los golpes, bruto... tendrías que usar un punzón o un extractor de ganchos.
@leonardochavez479910 ай бұрын
golpear directamente el eje para que salga no es algo tecnico, ya que deforma la punta del eje, si se cambia la corona se debe cambiar el rodamiento
@aegonwelding61992 жыл бұрын
Where you got this gear
@cyberbunny100
2 жыл бұрын
Hey, Bosch has a very good homepage where you can reorder almost every part.
@aegonwelding6199
2 жыл бұрын
@@cyberbunny100 website konsi hi
@mnarsk5853 Жыл бұрын
।। 🎉ট।😊
@musichillsrecords3065 Жыл бұрын
wrong fitting
@MyNeighborsaJackAss4 ай бұрын
Was it expensive for the parts and the necessary tool. I’m guessing it would be the same to get a new one maybe?
Пікірлер: 24
Great way to destroy your axle(just like you did :P). If you have bearing separator AND bearing puller then just simply hook puler to the separator. If you have only separator just clamp it like you did and then use 2 screws, and ~10mm steel bar to push the axle. Separator have 2 vertical holes, one on each side - use as large screws as possible. You need to drill 2 holes in steel bar in correct distance to push that axle. If you don't have separator / puller you can use long socket and hammer, but please use at least copper coin on top of axle to not destroy it like on this video.
Muchas gracias por el video es de gran ayuda Dios lo vendiga
many thanks for your help. now I can repair mine with same problem. thank you so much- renato Italy
@cyberbunny100
2 жыл бұрын
You are welcome.
Ok! Muito bom mesmo! Valeu 👍👍
Thanks so much it worked 👍🏾
Thanks Man!
Техника ,на высоком уровне разборки ушм блогадарю, учус.
Ótimo trabalho parabéns 👍👍
@cyberbunny100
2 жыл бұрын
Muito obrigado.
Super Job , ich hab ein PWS 620 , das was Sie repariert haben , ich meine die Kugellager ist defekt die mit Getribe (abstands metal ist kaputt und die kugellagern die bleiben alle zusammen .
the gear housing, can fix other brand ?
You need to put a little more grease
@cyberbunny100
3 жыл бұрын
Thanks for the tip.
can use any type of greese oil ?
@cyberbunny100
3 жыл бұрын
No, a special grease is specified in the operating instructions.
Destruido el eje por los golpes, bruto... tendrías que usar un punzón o un extractor de ganchos.
golpear directamente el eje para que salga no es algo tecnico, ya que deforma la punta del eje, si se cambia la corona se debe cambiar el rodamiento
Where you got this gear
@cyberbunny100
2 жыл бұрын
Hey, Bosch has a very good homepage where you can reorder almost every part.
@aegonwelding6199
2 жыл бұрын
@@cyberbunny100 website konsi hi
।। 🎉ট।😊
wrong fitting
Was it expensive for the parts and the necessary tool. I’m guessing it would be the same to get a new one maybe?