Captures the process of removing a leaking transmission seal and replacing it.
Жүктеу.....
Пікірлер: 26
@rodofiron595710 ай бұрын
Absolutely love the spline cleaner. Thanks from another Borg Warner operator!
@robvalderrama2948 Жыл бұрын
Great tutorial Captain ! You’re old school resourceful. Love it
@markharris27783 жыл бұрын
Fantastic video. I’ve been looking for this for quite some time.
@kylequinn77602 жыл бұрын
Great how to video. I have a leaky seal and will be tearing into it next week. Very helpful insight and ideas for tools and technique. Thanks, I love KZread!
@dwkmk32 жыл бұрын
Thank you! been a while since I have done this - since like 1996/97. Good refresher.
@rondetal3004 Жыл бұрын
Thank You.. for the instructional video and excellent service narrative !!
@revjeffrudolph4 жыл бұрын
Thanks for making this video, great job! We will be tackling this job later this week.
@jonsm114 Жыл бұрын
Thanks for Producing this video.
@laurieledden1154 жыл бұрын
Thank you for the expert video, doing this job this weekend. Rick Ledden
@romakayak9 ай бұрын
Put an O ring on the shaft and then the flange
@alexanderledwith17804 жыл бұрын
Very good video.
@mjay65674 жыл бұрын
What's the trick to separate the coupling and push the shaft to the aft? I'm doing this in the water. Loosened shaft packing, but having issue seperating the coupling to get to your first picture in your video... the actual separation. Appreciate any advice... thank you!
@mjay6567
4 жыл бұрын
Thank you! Got har started moving. Used a couple of putty knives to get things going. Only about 1/4" apart right now. Will continue to turn and wedge/pry.
@wearethe80s4sure2 жыл бұрын
Good man, so i figure that i can work on my tranny in the boat. Problem shifting into forward...
@rooroo1404 жыл бұрын
How did the silicone get in there?
@garrenhightower2737 Жыл бұрын
Was this done in the water
@Steve-qo4hi4 жыл бұрын
Thank you so much for this! 2 questions if I may.Did you do this while in the water? Were you noticing oil (atf) in the bilge? Thanks in advance. Also guessing your in NE like me😏
@ShastaFantastic-bh5qc Жыл бұрын
I wanted to see the process of detaching and then attaching again the shaft from the trani, it does not compute for me :-(
@jamesthompson65853 жыл бұрын
Nice video! Would you happen to know where I can get a seal? 3.5 OD 2.5 ID I've been searching everywhere. The seal in the seal kit I ordered is just too small.
@Mrrichardbancroft
3 жыл бұрын
Transatlantic Diesel in Hayes, VA has the seals. They sent me the wrong one first, then the right one.
@all4runners1164 жыл бұрын
Are the threads on the flange nut left-handed? Seems like you tightening the wrong way. Thanks
@AndyKopac
9 ай бұрын
We’re the threads standard or reverse. Left or right
@kimcater33512 жыл бұрын
Would have been good to see the old seal removal, and the new one inserted, otherwise very informative
@sailingashika57232 жыл бұрын
Nicely done. This is my trans but I need model number or part number for the seal, can you help me?
Пікірлер: 26
Absolutely love the spline cleaner. Thanks from another Borg Warner operator!
Great tutorial Captain ! You’re old school resourceful. Love it
Fantastic video. I’ve been looking for this for quite some time.
Great how to video. I have a leaky seal and will be tearing into it next week. Very helpful insight and ideas for tools and technique. Thanks, I love KZread!
Thank you! been a while since I have done this - since like 1996/97. Good refresher.
Thank You.. for the instructional video and excellent service narrative !!
Thanks for making this video, great job! We will be tackling this job later this week.
Thanks for Producing this video.
Thank you for the expert video, doing this job this weekend. Rick Ledden
Put an O ring on the shaft and then the flange
Very good video.
What's the trick to separate the coupling and push the shaft to the aft? I'm doing this in the water. Loosened shaft packing, but having issue seperating the coupling to get to your first picture in your video... the actual separation. Appreciate any advice... thank you!
@mjay6567
4 жыл бұрын
Thank you! Got har started moving. Used a couple of putty knives to get things going. Only about 1/4" apart right now. Will continue to turn and wedge/pry.
Good man, so i figure that i can work on my tranny in the boat. Problem shifting into forward...
How did the silicone get in there?
Was this done in the water
Thank you so much for this! 2 questions if I may.Did you do this while in the water? Were you noticing oil (atf) in the bilge? Thanks in advance. Also guessing your in NE like me😏
I wanted to see the process of detaching and then attaching again the shaft from the trani, it does not compute for me :-(
Nice video! Would you happen to know where I can get a seal? 3.5 OD 2.5 ID I've been searching everywhere. The seal in the seal kit I ordered is just too small.
@Mrrichardbancroft
3 жыл бұрын
Transatlantic Diesel in Hayes, VA has the seals. They sent me the wrong one first, then the right one.
Are the threads on the flange nut left-handed? Seems like you tightening the wrong way. Thanks
@AndyKopac
9 ай бұрын
We’re the threads standard or reverse. Left or right
Would have been good to see the old seal removal, and the new one inserted, otherwise very informative
Nicely done. This is my trans but I need model number or part number for the seal, can you help me?
Reference the oil seal ?