I have an e91 320i 2011. After a 1.5 year of expluatation i have to say that it's my first BMW with no troubles. ;-)

First video I’ve found explaining the n43 engine! Perfect job. Cheers

@d1and0n1y6

3 жыл бұрын

Agreed

Great video. Loads of info in a short space of time - exactly how I like it.

Finally.. Someone who knows this engine!! Great video. I now know I have the fuel injectors and NOK sensor issue to sort on my E90 320i (mental vibrations from the engine), might swap out the Timing chain as well. Expensive car to maintain I have already done the diff and electric waterpump, both failed at very low mileage. Thanks Again👍👍👍

@zdravkobelinski4627

16 күн бұрын

my car is 56k miles and already has the rough idle issue. I bought it cause london ulez zone but might sell it and just use the train. It upsets me super much, also mine is e93 so is a bit heavier and slower, very clean car but i dont like to be upset so

Hi mate, nice video, very informative. I only wish I'd watched this a month ago. To cut a long story short, 2 weeks ago my dad bought 2011 e90 318i (N43 engine). We took it for test drive, faultless. Drove it back home 80 miles and it was sweet as a nut. Parked it up outside the house and left it half an hour or so. Started it up, pulled it on the driveway, revved it a couple of times and it started knocking like you wouldn't believe! Initial thought was bottom end. The looking on youtube it had VERY similar diagnosis to air con pulley or any pulley noise for that matter. Further inspection and releasing the belt proved it wasnt a pully, much to our dismay. We drained the oil, fearing the worst (expecting metal particles etc, but no, oil was clean, filter too). Then when I mentioned to a mechanic friend the car had a new clutch allegedly fitted before my dad bought it he said possible dual mass? Changed the oil and filter and fired it up, the knocking noise again! Then as it warmed up... it went silent and sounded like a Swiss watch! Exactly like when we took it for a test drive and the 80 mile journey home. Then, when pushing the clutch pedal in and out and moving the car backwards and forwards, the noise became apparent again. What's your thoughts? New clutch fitted with old fly wheel? Knackered flywheel? Knackered clutch and flywheel? Like I said, it drove back 80 miles sweet as a nut. If it is the flywheel and or clutch... how many hours SHOULD it take to replace and which manufacturer of parts do you recommend? Obviously BMW will be ridiculous. I know a few people capable of doing the job, albeit a tough one. Any advice would be much appreciated, cheers mate.

I have only 1 complaint mate you talk very fast, great vid and at last tutorial for our European 2ltr engine

@MerakiGrace

2 жыл бұрын

there is an option to slow video down xD

@levrone0075

5 ай бұрын

Interesting. It seems to be the norm now because of time sensitive apps like tiktok. But I agree with you as an old school brit I value time to digest what is being said

@ams0876

4 ай бұрын

I had to slow down the video to understand what he’s saying

Nice explanation about our engine. With 195k km my inyectors failed and i got rough idle and bad running first minutes (they were index 3 and were changed for index 11). Also chain was loose and needed to replace (tensioner and guide as well). Also changed ignition coils and spark plugs. Now runs perfect, but Nox sensor is next... This engine needs a lot of care, as well as some ista or inpa software to "read" it.

@BMWDoctor

4 жыл бұрын

Glad it helped

Great vid bro just got my first bmw about a month and knew nothing about it no one else’s videos make sense too me

Interesting to hear about this engine, Dean. Good video. Thanks for sharing!

Great video Dean, thanks for all your time and effort. I have a 2010 E90 318i, I can do basic stuff like brakes, oil change but I don’t have the facilities for anything big. Is it a big job and costly to replace the chain guides/tensioner please. Many thanks

Great info spot on Was unlucky when i bought my N43 2and a half years ago had my engine replaced by BMW 2 years ago bought it 3 months before the timing chain bits got into the sump and engine failure BMW replaced new engine for £4.500 50% reduction thought that was great value as they said engine was 9k anyway also i replaced the nox sensor £280 oem from spain as i was getting 30EA nitric oxide catalytic converter, sulphurized codes hasnt got rid of the code but i need to do a désulfuration on inpa 70mph for 1/2 hour etc so my car has cost me about 5.5k that a grand more than i bought it for but at least ive got a new engine and ive also coded the car to the best of my ability using ncs expert etc Thanks agin for Video 👍

@BMWDoctor

4 жыл бұрын

Your welcome mate I know only too well about this engine trust me and it’s flaws it’s something we saw daily in the garage we had about 100 of them a week in

@kaboomist

4 жыл бұрын

Hi mate, do you have a link for the OEM NOX sensor? Only place I can find it is BMW website and they want £450.

I had most of the problems he discribed, i had bad injectors that caused a misfire in 3 cilinders. I did not know at the time so i replaced the sparkplugs and ignition coils, it did help with how smooth the engine was running but when the car was idling it still misfired. 3 months after that i would hear 3 seconds of rattaling when i started the car, soon after that i would get low oil pressure warnings on my dashboard if my car was reving above 4,5k after that i was driving on the highway and lost power, alot of white smoke came out of the exhaust i knew that it was either a head gasket leak or bad injectors but i think it was a combination of all the problems i just named above. I took it to a bmw specialist they took apart the engine cleaned all the oil chanals replaced the vannos, timingchain and rails, all the injectors, and all the damaged parts of the engine because i drove it with a low oil presure i also repaced all the gaskets it ended up costing me 3000 euro to fix all this. This was 6 months ago and i did not have any problems yet but this engine is a nightmare i would stay away from it. I also know some of this could be prevented if i figured out the problems sooner and took it to a garage but an engine is not suposed to fail in such way. Ps sorry for my spelling faults

Great info given there, just bought a 2011 318i with N43 unit for my son’s first car, 3 days latter engine seized! We’re going to pull it out and assess damage ourselves as cost of being rebuilt professionally is just more than the car is worth!

@Framus-wm3ye

2 жыл бұрын

Sorry to hear about your experience, how many miles had the car done when the engine gave up?

Thanks for the vid, had to slow the video down though you talk super fast 😂😂

Thanks alot dude,you are taking this much time and effort even in breathing disease just to explain to us (whoever watches these videos) SALUTE!!

@BMWDoctor

4 жыл бұрын

your welcome and yes mate im trying to get better but i have all you guys who also depend on me so i have to continue whatever happens for you guys

@itzpro.

4 жыл бұрын

@@BMWDoctor i depend alot because i have bmw and that costs much high to even diagnose the problem so i just get the correct idea of what can be wrong and change it .... the car runs perfectly fine

@philipabboud2932

3 жыл бұрын

Hello.. Nice video.. When i put the scanner, my car did a misfire on cylinder 1 and 4 and a problem on the oxygen sensor.... What should i do first? N.B.(new ignition coil and new sparks)

My 16th car. E88 n43b20. Bought it 7 months before with 118k km. Since i bought it (11k km) i have changed: All 3 Oxygen sensors Nox sensor Coolant thermostat Did the valve cover seal (always use reizonsil anthracite and wait 10hours - it will last longer) Changed spark plugs twice. Changed ign coils twice. Changed injectors to index 11 Cleaned vanos solenoids Changed coolant with oem bmw (not expensive) Of course cleaned maf and throttle body Reset engine and throttle adaptations several times using my Thinkdiag+ Also watching short and long fuel trims and fuel rail pressure through car scanner app and vgate pro bluetooth obd. My advice is that: 1. only ngk bkr7a-htu plugs 2. better buy delphi ign coils because the rubber sleeve on Bosch ones is getting damaged very easily. 3. Watch long fuel trims on startup and when heated at idle, 1.5k rpm and 2.5k rpm. If there is significant variation between bank 1 and bank 2 ones, then visit a bmw specialized repair center. 4. change injectors to index 11 because there are large batches of index 12 which are coming from China. 5. Clean the ign coil grounds (brown wires screwed on the engine block) using 800 grit sandpaper. Many thanks for the informative video.

@BigHumz155

Жыл бұрын

Delphi coils are a big NO for this engine !!!

@YusufIslam1

Жыл бұрын

​@@BigHumz155 why?

@janek8582

Жыл бұрын

hi how did you know you need to clean the coil ground wires? i have replaced the coils and they work fine but sometimes they start misfiring. it usually goes away after some time and mostly can be felt on idle. i’m also suspecting there may be a link between moisture and this issue. could you give me some advice on this issue?

Ok…so I’ll stick to my n52 e91 search. Thank you so much for the great video!!

Timing chain guide and oil strainer fix with oil flush. Happened to me first week I bought the car private. Oil pressure light came on, when I turn car off and on the light goes away. Did it every now and then. Diagnosed the issue and tried an oil flush first for 15 minutes. Problem been fixed for 8 months now 👍🏼

@RedlioNxTR

2 жыл бұрын

I bought mine in 2014, since day one, I've had oil lamp on after the engine gets hot. What did you do exactly?

@metalman4141

10 ай бұрын

@@RedlioNxTRsame here

@skansii9279

5 ай бұрын

@@metalman4141 change chain and tensioner, its broken probabbly

This video is VERY good. Thanks bud

Thanks for the extemely valuable information.

Have a 2009 120i N43, In the last 3 months Ive had: A new timing chain kit, new oil pressure sensor and hydraulic valve, sump cleaned out as had broken guide bits, new rod end bearings, new engine mount and mount cover. Now need a new Vanos.

@Framus-wm3ye

2 жыл бұрын

How many miles had the car done before you had these things go?

Would you recommend purchasing a 2008 BMW E87 120i? I've heard continously horror stories on forums to just stay away from it? My other option is a 2005 BMW E90 325i. I know there is a million other factors, however generally which is the more reliable engine?

huh thanks, I almost went for 320i e93 but after checking this vid, I'll pass on it. tnx again, great vid.

Hi, thanks for this video. It is also the first good video I found on the Internet. I wanted to ask if it is a good Idea to tune this engine a bit? And when it is, where can I get the parts. I have the e90 320i with the n43 b20 engine with 170ps and whould really like it to go like 250ps if that is posible. I thought of a better air intake, a better exhaust maybe a sharp camshaft and ofcours a good tune. Thanks

Thanks ! from a n43b16 owner

Great video, very rare for someone to exactly tell my 7 years of frustration. I've replaced most of the things you mention, expect for the injectors as they're so expensive. I guess I'll have to now. 😂

@Framus-wm3ye

2 жыл бұрын

How many miles had your car done before you had all those problems and how many miles is it on now?

@wytzzmf

2 жыл бұрын

Selam, I have the same issues. Satip satmama konusunda karar veremiyorum.

Hey, great video! Just one quastion of n43, always use original spark plugs? Ik have bosch but they say it is not the same, thanks

@blame182

4 жыл бұрын

Use NGK only

driving an E87 118i 2007 with 155.000KM here, it's still running with its original timing chain and it just got regularly the services it needed like oil and filters. The last documented repair it had was with 110.000 where the camshaft sensor had to be replaced. Oil was changed every year between 8tkm and 15tkm Fuel usage is sitting at 8.5/100KM, I believe that it could be an litre lower but my OBD doesn't say anything about NOX or anything so Im just living with it

@BriBri07

6 ай бұрын

After 150k kilometers you really should start thinking about your chain. I just replaced my timing chain after 110k kilometers and it was stretched almost one chain link lenght compared to the new chain. Because of that it was also a bit of timing

@WayToManyAssassins

6 ай бұрын

​@BriBri07 is there a replacement chain kit that doesn't stretch?

What about carbon deposition on the inlet valves? I haven't heard if it is a problem with this engine, although it is direct injected

Good information , well done ✅

If your timing rails break and block the strainer you must check your big end bearings. If they have spun then you have to change the rods which means head off.

Nice video, thanx! I also own a N43 engine. Had a lot if problemen already, changed coils, injectors, NOX-sensor.. One day, i got an oil pressure warning light. So pulled over immediately. Turned out the chain tensior came out. For some reason it became loose. A random garage changed the small ring and put the tensioner back in. Do you have a experience with loose timing chain tensioners? Would you recommend changing the tensioner or is changing the ring sufficient?

@MatiKosa

3 жыл бұрын

Best advice is to change the tensioner every 80k km (~~50k miles).

Not a word about hydraulic valve.. Anyway the best video about n43;

After timing chain failure. Don’t forget to replace the oil pressure relief valve. Fitted on your block under the alternator.

My guy here shook me when i heard him say Trinidad, that's where I'm from, my dad has the only 2009 E90 320i m sport model, and tbh he isn't showing it the love it needs, he used to drive a camry, so it worries me a lot, he waits until some fault or the engine light shows up on the dashboard, that's what a lousy Camry driver does, not what a car enthusiast does, and he still takes sharp turns likes he's driving a slow ass FWD car, i told him that since it's a RWD car u shouldn't completely let off the gas, because while u give a rwd car 25% of gas while entering a turn it helps u turn sharper.

I have the 2.0i n43. Already had the shattered chain guides loose chain. Managed catch that before causing catastrophic damage but still have a strong smell of fuel rough idle & misfire. Nobody can diagnose or have different diagnoses on it. MAP SENSOR. NOX SENSOR Or the injectors all expensive repairs & not sure which will cure it I hate this car so any advice ?

Was wondering if i could get some advise , car was running fine mileage 68k FSH put it in garage to change spark plugs and now car misfiring cylinder 2 changed coil still no difference any advice ?

ive owned a 2008 e90 318i business with n43 issues so far are powersteering failure but managed to buy a salvaged part for 80€ that fixed the issue then rear axle snapped due to rust and we needed to change the timing belt ( not an issue since u have to change it from time to time bought the cars with 250k kilometer on it so it was time to change it) those are the only issues after 1 year of ownership and over 70k kilometers on it money spent total about 1000€ and i think that is all the problems atleast for a while im happy with it exceeded my expectations

@filipdaniel7553

2 жыл бұрын

This engine has no timing belt.

Very well said and at least I know now my bmw 116i 2.0 n43 is fucked for the reason you mentioned black plugs nox sensor codes and running rich with a misfire and a smell of petrol just great.

Great Video mate!! Got the same engine for a year, got the same problems, replace the injectors and runs better now but sometimes the check engine light comes on, after a sport drive on motorway, about 30 min goes off. No difference on the engine when the light is on, runs the same. The tester said that the catalytic convertor is clogged. But anyway, is a great engine if you take care of it. My one have 193k miles and still purse like a cat 🐈

@roymoorman5990

4 жыл бұрын

how does your intake manifold look like ? Mine was super greasy and led to carbon buildup on the intake valve stems. May have been oil seperator failure on mine.

@sciencegod1

3 жыл бұрын

How has it been holding up for you later?

Thanks so much for this video! Do they run 5W30 fully synthetic or non synthetic? Cheers for your help!

@BMWDoctor

3 жыл бұрын

Yes they do indeed my friend

@BMW Doctor , I have been subscribed to your channel for a while now, and I have to thank you for the awesome job you do ! Thank you for your awesome videos regards BMW vehicles! I own a 320i with the N43B20A engine and I got to misfiring issues lately as well as excessive vibrations in the cabinet. I have changed ignition coils, spark plugs and injectors but the issue looks like it doesn't go away !!! Please HELP!! I have spent already a big amount of money so I can solve the issue but it looks that something else is wrong ! Is there a way we can come in contact to explain in details my situation and possibly you suggest me what to do !!! I am so desperate that I reach the point of looking for a new engine swap, as the cost of working on this engines is very high. Swapping engines looks like it the cheapest way to go ! 🙏🙏🙏 PLEASE HELP !!!

@Pwasercan

Жыл бұрын

Hi, I have the exact same problem. I already spent 1000€ changing ignition coils, spark plugs and 2 injectors for nothing. Firmware update on the whole system fixed it somewhat, for a few months, but then the failure came back again

Thank you so much for this video. Only if you did it a year ago when I was looking for car and fell into the N43 money pit (luckily not a single problem yet at 146k kilometers with a 7-8k km oil replacement and 12-15k km spark plugs replacement)

@Raulz0r2

3 жыл бұрын

Then how come is a money pit if you had no problems?

@sciencegod1

3 жыл бұрын

How is it holding up for you?

@TinyJackal

2 жыл бұрын

@@Raulz0r2 well, evaporator cooler (the one inside the dash), battery and electrical issues, nox sensors, n2 catalysts, set aside oil sump gasket, cylinder head gasket, shocks, A/C leaks and so on.

@TinyJackal

2 жыл бұрын

@@sciencegod1 after I bought it and spent a good amount of money on some known issues, it holds ok. I’ve driven 40.000kms on this car which now stands at around 175.000km, oil and gas consumption went up (clogged catalytic converters from burned oil), 2 of the ignition coils went in a better place while driving at the same time, some of the front end steering parts failed but is normal wear and tear. Overall I would say it’s ok if you make sure to spend some money on preventive maintenance.

Hey Doc, my e88 is 2010 47,000kms and I baby the hell out of it. It runs like new every day.. regularly have a local euro specialist maintain it (preventative). Any thoughts on this engine reliability when baby'd? I don't race or drive harsh as it just gets me 10km to work and back daily. I let it warm up a bit every start and just cruise in it. Do you think the engine is simply not cut out for lead footed drivers? Is it the engine being driven hard that throws all these faults or is it inherently flawed no matter how you drive it?

@sciencegod1

3 жыл бұрын

I'm curious to know, have you had any of these major problems with yours?

Are you in the uk mate? Around the London area preferrably

Hey, May I ask what is your opinion on NOx sensor being coded out just like the SS procedure ?

@lefterisapostolou6616

3 жыл бұрын

Pease answer

@YZFMANIAC08

3 жыл бұрын

Kills your catalytic converter

I think my BMW has coronavirus as it's coughing pretty badly.

How do I get a hold of you? Is the ista software good for e45 335i

spark plugs notorious for failure? Wouldnt that imply a bad factory mapping?

English is not my language so it was a little bit fast to me :D. So to ask here, is the engine reliabile or i should look for the disel engine?

oh dear just bought a 2012 e92 2L , do i need to sell my house to pay for impending repairs ? , it's off to the garage on wednesday cos its developed a oil leak.

Hi, please help 🙏 BMW 320i Coupe, 125 kW (manuf 06.2008). I've had an engine failure for many years, where the yellow engine symbol starts flashing on the panel, and the car starts shuddering and the motor sounds starts squeaking and it no longer gives power properly. And starts smelling of burned if kept running. But then if it rests a few hours, most times it continues to work fine, other times the issue persists. When I took it to the official BMW service, they deleted the registers and said the car was fine. So I took it to my local repair shop. I've had 2 inyectors replaced, but one keeps failing even after putting a new one (nr. 3). Also a couple of ignition coils and spark plugs have been replaced for the same 2 cylinders. Apparently, at first the gasoline was spilling out and leaking into the oil deposit. The only TEMPRORARY fix has been a FULL firmware upgrade to the car's system. But it suffered the same engine problem again 6 months after that. This failure has happened more than 6 times throughout the past 10 years. And even when it's supposedly fixed, the motor is rough on idle and the car always shudders a bit, and when starting the motor, sometimes I hear a cracking noise like something is clashing, probably "engine knocking", which also happens when I tap the accelerator between 2000 and 1000 rpm, especially when starting to move on an upward slope, and starts smelling of burned if I do the same over and over; but the mechanics say this cracking noise and unstable idling is unrelated to the engine failure, and it's just the age of the car (2008 car). But I think it's all the same problem. The car used to be driven by my parents, who always drove it at very low rpm. But I've been driving it for 2 years at high rpms, most of the times I use gears to 5500 when accelerating, so it should not be accumulating soot inside the motor. I've asked for a motor cleaning, but the mechanic said it wasn't necessary on gasoline motors. I did have to replace my NOx sensor too last year. I have all the problems that were mentioned in the first few minutes of this video 😥 I don't know what to think, this seems like there is no solution. Can I put a "compatible" motor into this car from another brand or even a better one from BMW?

i have a engine light pop up after 1min from cold start up telling me its a cam issue , if iit leave it to warn up its fine is this an oil issue

Can anyone put up a rough guide re: pricing for all the jobs mentioned here at a good indy?

any idea why it would break the oil pump twice snapped at the input shaft broke the shaft at the chain driven cog, both pumps turn freely not seized, engines has had new injectors, coil packs, spark plugs, timing chain replaced, correct oil in it, new nox sensor, lamda sensor, oil pressure sensor all done around 110k. Berrings not damaged as car wasnt run seems to have occured on start up rattled and immediately stopped, 135k on the engine well serviced approx every 5-8k, chain was replaced as a precaution there was no issues with it. broke one pump before chain replacment one few weeks after.

@pmq01

4 жыл бұрын

chain just replaced at 135k

I run 5W40 on my N43 since 2010 with 200t km on it no issues so far.. Also first chain

@wytzzmf

2 жыл бұрын

hi Sacha, i have same car as yours with N43. My car had low oil pressure problem earlier. They changed it with new pump, but it did not solve the problem. After this, they put 10w60 oil (LL04) CASTROL. Do you think this oil is too think? Finally, my car had high pressure fuel pump failed 2 days ago. Do you think it can be because of using thick oil?

@WayToManyAssassins

9 ай бұрын

​@@wytzzmfthat oil is racing oil, not designed for that car

Great video mate one quick question does the NOX sensor need coding when its replaced. thanks in advance

@BMWDoctor

4 жыл бұрын

No you don’t need coding it’s not that special of a engine

@StefanTomic

2 жыл бұрын

You need coding, in order to reset the adaptions from the old sensor. That way ECU will know there is a new NOX sensor, which will also affect the engine performance (positively).

Hi Doctor, all what you mentioned is correct. I have 118i with N43B20A and fortunately in mine the injectors were changed still while on warranty by the dealer. The car is owned and used only by my father since new and has done only 30K miles. It's well maintained and oil changed frequently minimum once a year. Now unfortunately I definitely need to change the NOx sensor. It now was already verified so we know it for sure. I don't want to buy the one from the dealer as it is so expensive. I would like to find some proper one equivalent from other manufacturers. Should I buy the complete set sensor with electronic box or can I only buy the sensor itself and connect ti my electronic box which is in good working condition. Please advise which sensor to buy and where I can buy it, the relatively good one and reliable. Please help. Kind Regards, Mike

@EIRK2046Y

7 ай бұрын

Bimmerprofs. Look at google - noxem sensor.

Hi hope you are well. Does e43 sounds like dizel. No vibration,smoke or lose of power , runs like silk but sounds like diesel some time. I wish I had your email I could send you a short video. Is that typically? Thanks

@giosoftware

4 жыл бұрын

So do mine. It seems that direct injection motors sound this way.

Is there a way to permanently turn off the auto start-stop on the BMW 320i Coupe? The button only works until I turn off the car (with the key). Sometimes it has remembered the setting, but then I take it to the garage and when they give it back, the setting no longer stores itself in the memory. I've asked the mechanic to save this setting and he says it's not possible, that the firmware enforces it for environmental purposes. This is so confusing how sometimes the settings stays and others (maybe with different firmware versions?) it doesn't?!

I ve a problem with my BMW N42 318 it's making a knocking noise when it has not knocked, second the car switch's off while driving, am just from replacing a camshaft and a vacuum pump both which broke after replacing the camshaft is when I started having the problem of the car turning off while driving,

@cagemcleod1199

3 жыл бұрын

Did you find out the issue got sorta the same issue

Hi Doc, I have a irritating buzzing sound coming from the front passenger speaker. I guess there is an issue with the standard BMW professional radio/cd player. It's a 2010 1 series 118d. Any ideas from anyone appreciated.

@seanross8149

4 жыл бұрын

I think I had this, turned out the AC needed re-charging

Hi. I got the E90 318i, N43 engine. Sometimes I get a fault code (2A99) and makes the car sound like a tractor as the rpm goes up. Then the fault code comes up it makes no sound, but it reduced the engine power. Its been like this for a long time now, but I cant figure it out. I’ll be pretty thankful for help. Thanks

@tauseef7061

3 жыл бұрын

Hey, try cleaning the vanos solenoids, especially the exhaust one.

What can be reason why i get micro studers about at 1800 rpm? i have n43 320i.

Please do a video on N43 timing chain replacement???

Hello. I saw your video now and its great. English is not my language so it was a little bit fast to me :D amazing knowledge of BMW engines. I have this engine and I have the vibration problem when engine is warmed up. When its cold there is no problem. When engine reaches higher temperature the idle speed is decreased to 650 and starts shaking the engine... If I let the engine at idle for long time then it turns off cylinder 1 injection. I delete the fault code -29CD - the injection turn on again in cylinder 1. I have only one fault code is on alltime: 2EF7 thermostat. Is here any relation with it? Anyone who has any suggestion please? Why happen it at warm engine? I replaced ignition coils, and plugs. Injectors are originals. But I really dont understand if I have an injector problem, why arent there fault codes or engine light, and why not faulty alltime? Please someone help me. I write here because here are many people with experiences about N43. Thanks a lot guys!!!!

Had a 320i (2010 plate) with the n43 engine and had multiple problems with the nox sensor, fuel injectors, ignition coil, which caused misfiring on multiple cylinders also the head gaskett went. Luckily i had only had the car for 2 weeks so was able to reject the car and return back to the local dealer as it was within 4 weeks for full refund. Worst BMW engine ive ever experienced. Snap on error messages: 2A2C Mixture control 2A0F Exaust gas recycling valve adaption 2A2B Mixture control 2 29CF Combustion misfire on cylinder 3 29CE Combustion misfire on cylinder 2 29CC Combustion misfire on several cylinders 29D0 Combustion misfire on cylinder 4

Hi I have this engine could you help the throttle body clicking all the time at idle like it constantly trying to adjust no fault codes but very jerky setting off

Great video! I'm italian and I'm temporarily living in USA. I decided to bring over my 2007 BMW E93, with the N43 engine (now 80.000 km). Since my car landed in USA I started to have issues: first the four ignition coils, second an engine light due to the nox sensor (that I didn't replace) and then, after a year, the four injectors (seems that the engine light triggered by the nox sensor doesn't show up anymore, after the injectors have been replaced). I've always been sceptical about the gasoline quality over here, even if I've always used the highest grade, the 93. Do you have any suggestion on how to survive here at least for another couple of years? Any precoutionary measures to be taken? Thank you very much!

@Pwasercan

Жыл бұрын

same issues here with NOx sensor, injectors, ignition coils.. no permanent solution found yet :(

@petrinieminen7353

Жыл бұрын

There's a reason why these vehicles (BMW with N43/N53 engine) weren't sold in USA at all. The NOx cleaning system just can't take the sulfur levels of the fuel there.

I have recently purchased a 120i 2019 It pushed the front crank seal out and replaced and done again it also drops oil pressure after 15/20mins of running is this a known issue

So for a 316i/318i buyer looking at the E90 (and used to E36 simplicity!) where am I supposed to turn? All the mistakes made on the E46 seem to be worse instead of better. ☹

@petrinieminen7353

Жыл бұрын

E39. Similar size, worse fuel economy but makes more than up for it by vastly better reliability. Also nicer to drive, quieter and more powerful than N43. Just don't go for an automatic, it makes the whole thing thirsty and the GM automatic is also rubbish in reliability. The ZF one is good at least at that.

Hello guys, I want to buy the Series 1 from 2008, engine code being n43b16, the 1.6 gasoline engine. Do you have any advise for me because i want to buy with 95k km

I have a n43 with a mystery problem. I have idle problem when i start the engine, find out the fuel rail pressure is at 10000kpa, as soon as i accelerate goes back to 15000kpa no codes and the car drives fine. The engine is a tricky puzzle. Thank you

@user-lp8ro5lj8x

2 жыл бұрын

Did you manage to find the solution to the high pressure fuel rail?

HI @BMWDOCTOR MY ENGINE BLEW UP DUE TO OIL STARVATION. I DONT WANT THE N43B20A ANYMORE. WHAT'S A STRAIGHT SWAP OPTION THAT'S MORE RELIABLE?

@DomWayne

9 ай бұрын

😂😂😂😂😂

Hi, I've got an N43 luckily never had any issues with it, but sometimes when I do a long trip the oil light comes on dash in red ive plugged in carly and come up with 0030C1 code ( Engine oil pressure control) could this be the oil pressure switch? What would you advise?

@antoniocupic7969

4 жыл бұрын

I have the same problem. The timing chain guides break up and start blocking the oil pickup tube causing low oil pressure. You must replace the chain and remove all plastic guides from oil pump. Works for me

@Marcell-ux7rb

2 жыл бұрын

for me when I was traveling sometimes there was a warning / oil pressure engine failure ..etc / when I stopped and restarted the engine disappeared and then appeared after a while / after a few months I decided to change an oil sensor and another oil probe are all on the side engine block and very difficult to access! / then I put everything back together and the car went well and the error in the diagnosis was definitely gone! so two new bmw parts (£ 130) but the small oil sensor was very hard to remove because the plastic broke on the outside 😆, but I managed after a few hours 😅 / good, fun !!! 🗽

@eltigre7001

Жыл бұрын

@@antoniocupic7969 thats right i had the same issue the mechanic took a photo oil pump and there was plastic inside and i changed the chain as well then no problem

Hi i need an advice please, i have 32oi and after 2omins drive i get low oil pressure warning, but the car runs normal, what should i do? Thanks in advance

@RedlioNxTR

2 жыл бұрын

I've had this problem since 2014. No joke

@bmw doctor I will like get in touch with you I got bmw 525d msport 2005 and I want to block the swirl flaps

@BMWDoctor

4 жыл бұрын

Brother look on google there is many garages local to you

@sorinverdesi1284

4 жыл бұрын

BMW Doctor I live in Coventry and I know they are but they don’t have your experience any way thanks for reply to me

Hi BMW Doctor I have this engine and I m struggling to diagnose a problem. The car runs smooth but once I accelerate on the motor way check engine will come I scan the car it will give me Lambda sensor bank 2, mixture control and NOx catalytic sulphur I changed the NOx and the Lambda bank 2 but still having the problem Can you advice on that please

3,5 years with E91 LCI 318i and I've really had enough. I do only 5k miles per year on average and the sodden crap can't manage even 8-9 months without having something broken. And no, not due to poor maintenance, I've always maintained my cars very well and frequently. E.g. oil change every 4-6k miles with high quality oil and fuel system cleaning with high quality fuel system cleaner designed for direct injection in this case. In 3,5 years and around 16k miles (from 109k to 125k miles) having to do the following repairs (besides the usual maintenance): - 4 new injectors, á 400 € - 4 new ignition coils, á 30 € - One new A/C pipe, 250 € incl. emptying and refilling the A/C - one broken ABS ring, 50 € for the pair of sensors and rings - one blower motor, 80 € - blower motor frozen solid (yes, the new one!) every winter starting from -15 °C down - camshaft position sensor, exhaust side - desulphurisation of NOx sensor, fortunately have managed by driving, no new sensor needed YET - thermostat housing, the old one had cracked, 0 € due to happening so soon after buying the car from the dealership. Summary: If you want a reliable car, stay away from this heap of junk.

@cosmos2382

Жыл бұрын

But.. i want a bmw..

@xgamer7869

Жыл бұрын

Feel sorry for you, i have good maintenance as well, car has done 320.000km and I have really not had that much expenses only trouble with vanos and it cost me 5£

Is this engine also in the BMW 1 series 118i convertible from 2010?

@motivesupplies

3 жыл бұрын

Yes

Dewd, I'm just buying a N43B16 and I think its MPI not DI?

I'm have some issues with my n43 engine is there anyway I can contact you for some advice thanks in advance.......#bmwTrinidad

i had a bmw 120i (n43b20a) my lord it costed my soo much the car its self wasnt to bad but i had to get new injectors, fix nox sensor £580 then water pump and thermostat another £550 then the timing chain went £900 this car gave me sooo many issues he has mentioned in the video i took care and serviced the car in 8000 mile intervals but even then still too many issues im just a uni student so this car was costing me tooo much so went back to a lovely fiesta if your car has this engine just run away it aint worth it.

@Framus-wm3ye

2 жыл бұрын

Oh god I just got one and seen this video, how many miles had your car done when it gave you all these problems?

@V1PERB3ATZ

2 жыл бұрын

@@Framus-wm3ye how is it? I’ve got one as well and 😩

@carlphillips5828

2 жыл бұрын

Lol I'm now driving a Peugeot 206 after this bad BMW n43 engine and I like this 206 much better 🤦

I have a BMW 318i n43. I have had the timing chain changed by BMW dealers. A few months ago I had a fault come up stating that I had to stop the car and get help,also brake load fault. I go the AA out and he said that a nox sensor fault came up saying something about regeneration. Any idea what it could be?

@RedlioNxTR

2 жыл бұрын

After timing chain, the engine was shaking like crazy sometimes. For me it was either the exhaust or intake camshaft sensor, can't remember which. They're cheap tho

Thank you very much ! I have a 318i from 2009 with this engine. I have a plug unplugged but cannot identify where it goes... located at the rear of the air intake manifold... Would you be able to help me ? Thanks !

Been running this one (n43b20a) in my 320i E92 for some time now (1.5yr), already done my coils (4), sparks (twice), vacuum pump, noX sensor and some cover gaskets. Other than that, it runs really well and doesn't sound that bad at all - at least while driving. I get around 10.5-11.5 litres petrol in the city and around 7.5-8 when out. Still running on the first timing chain tho, now at 220.000km, replaced the tensioner with a newer one (last revision), but I'm planning to do a full timing chain setup brand new this year as it's not that expensive when buying parts yourself and doing service somewhere else instead of the dealers. Two things annoy me the most about this engine, okay - three. 1st - lifter tick, no matter what you do, how you drive it or what oil grade you use, that clicking sound will get you, 2nd - I sometimes get a red oil pressure light although the oil is on max, no codes, and the timing chain isn't to hear from at all, I guess the oil pump is planning to say something to me pretty fast, and 3rd - the engine runs rather hot, so you better check that coolant level and quality regularly. I mean, I don't really find it that notorious at all, at least when compared with a N47, and oil changes between 8-10.000kms, it is really possible to run on first chain even on high kms such as 200.000+.

@BMWDoctor

4 жыл бұрын

My friend you are like the Americans Why you write some long essay ??? Nobody is going to read this I don’t understand why people waste there time writing all this Be like Uk people write a couple of words and DONE

@drazenivanda9514

4 жыл бұрын

@@BMWDoctor sounds a bit ignorant, don't you think? Why would you want to have such a nice and useful channel if ppl would respond with agreed and not agreed.. In other words, I loved to hear what you had to say on this topic, shame it wasn't the other way around tho.

@BMWDoctor

4 жыл бұрын

No I’m fine with you commenting But why so much detail what for ???? What is that exactly going to do for anyone And mostly when people start commenting and commenting I just remove the comment or remove them completely I’m in full control here mate But your comment is useful YES INDEED but it’s a bit long winded

@BMWDoctor

4 жыл бұрын

Boooooo 👎 I was thinking it might destroy itself and get yourself a proper bmw with a 6 cylinder engine I hate 2.0 engine

@drazenivanda9514

4 жыл бұрын

@@yinsaya6067 ofc you can, treat it right, and it will give back. I've done some 25k km with it, oil twice a year, all filters and sparks, plus Doc's advice and gg. Actually pretty crazy but I kinda like it, having in mind it's "only" 4cyl.

Recommended to watch this on 0.75 speed. Great video though.

I wonder if you own a proper garage Mate? If so, where about in UK?

So basically if I understand this properly BMW makes cars according to the regulatory requirements that precede selling them. I am looking to get a 2012 e92 with N43 engine and it does not have a start stop button or feature whatsoever. Our regulations are not as strict, well at least they were not at the time

@RedlioNxTR

2 жыл бұрын

Stay away or visit it at the workshop from time to time

He spoke nothing but the truth 💯

Why do they say the N43 is the worst engine??? I am interested in the 320i due to its price actually at the moment but I usually see a lot of bad reviews about it. Is it worth it ????

@flyintheskyd3214

2 жыл бұрын

Dont do it ! I had the car two weeks and had multiple problems. Ended up rejecting the car and giving it back to the dealer. One thing thats guaranteed with this engine is a hole in your pocket.

Yep, I’ve just bought a BMW 120i with the N43 engine and it developed the dreaded misfire on day 6. Had the Nox sensor replaced (under warranty) but I feel this ain’t the last of it.

@BMWDoctor

3 жыл бұрын

No it ain't the last of it trust me on that.

@YusufIslam1

3 жыл бұрын

And I just got a 120i N43 as well. Really not liking the fact about the nox sensor.

@Framus-wm3ye

2 жыл бұрын

@@YusufIslam1 How many miles had it done when this happened?

Hey guys. I have a BMW 2011 318i E90. Recently after driving it i noticed a red engine light half filled in appear on the dash. I got the car scanned it came back to be a engine oil pressure control static code. Prior to this recently i did top up the car with 5W40 as it was low by a litre or so. I have a leak at the oil filter housing gasket next to the oil cooler. Has anybody else experienced this problem similar to mine and if so how did you fix this issue ? Was it because of the wrong grade of oil used or becuase of the leak at the oil filter housing ?

@romaniantech

4 ай бұрын

hey, while I did not get the engine light I do get the oil pressure static code from time to time. I also have a rough idle once in a while and I am also using 5W40. I bought a new OE 11417584990 hydraulic valve but did not replace it yet, together with the oil filter & oil cooler gaskets as they are also leaking. Did you find a fix for your issue?

Still i'd prefer the n42 as a 2L because it's just naturally aspirated, means that yes it uses more fuel but these kind of engines are just more reliable. Point.

@filipdaniel7553

3 жыл бұрын

N43 is naturally aspirated as well.

@kjschrauber2126

3 жыл бұрын

@@filipdaniel7553 Ik but it doesn't use Di, direkt injection, no NoX Sensor no nox catalyst

Should I go for a N43 or a N47?

Cool👍

I have received a warning message on my idrive "high braking load" along with "high brake load drive moderately". I would like to know what this is. And how can i fix it. Car is still driving as normal. Brakes and acceleration pedal still feel normal. The car has covered 56k miles The garages i have gone to havent come across this before. Has anyone else come across this. Thanks

@filipdaniel7553

2 жыл бұрын

You have a vacuum leak somwhere. Go to a service.

Hard to believe some of the comments on here. I'm certain many of the haters are under 30 years old and bought the cheapest oldest E9x or 1 series BMW with the largest rims, did not check its maintenance or history, and beat the hell out the car , only to then complain that it leaks or misfires... When I see N43 cars for sale, you can tell what kind of owner are selling them, cheap budget tyres, DIY repairs, non genuine parts, and all the rest of their 'maintenance' is spent on LED light or 19 inch wheel upgrades ...it's no wonder why the 15 year old engine gets a bad rep now...

My N43 318i developed bottom end engine damage not long after I bough it….suspect some of the plastic timing chain guides to blame being drawn into engine - Nox sensor and injecyors are new but cost a ton to repair and i doubt that’ll be the end !

Why no ...W40 oils? I read in a lot of BMW forums and have private contact with the engineering and development department from SHELL. The overall recommendation for the N43 is a 0w40 full synthetic with advanced additive package BECAUSE of the problems with the chain. 0w for better lubrication of the chain/chain parts on short distances where the oil isn't getting to its working temperature properly and the 40 for a buffer of viscosity when theres a case with loosing oil pressure.

@marceldobre

4 жыл бұрын

I would have the same question. I was about to replace my 5w30 with 5w40 because oil pressure and oil lost.

@sir7586

3 жыл бұрын

Good question, hopefully we'll see an answer

@petrinieminen7353

Жыл бұрын

So far no issues whatsoever with Liqui Moly TopTec 4100, 5w-40