Soo thankfull that people like you actually take the time to make videos like these! So incredibly nice of you. Thank you!

@TheKeenMechanic

10 ай бұрын

My pleasure😊

Excellent video, used it on my side to clean out the EGR on my, 535D F11, very helpfull. Just had some trouble on the crispy connectors

@TheKeenMechanic

Жыл бұрын

Hi and thanks for your feedback. I am glad to hear you found it helpful. When I get comments like this makes my day as I know my work videos have done their job🔧🔩🤝

Amazing video ! Thank you. According ista it is important to reset adaptations for air system - egr, after finishing the job.

@TheKeenMechanic

10 ай бұрын

🤝🤝🤝

Greetings from South Africa.. thank you so much for your in depth video.. it has really assisted me with doing the intake cleaning on my n57. Much appreciated

@TheKeenMechanic

5 ай бұрын

You are welcome buddy. Glad to hear you found it helpful

The best and most comprehensive video I've seen so far on this topic. For people with bi/tri turbo setups, another infamous failure point is the vaccuum system but otherwise doing all the things you showed will solve the problem for 99% of people.

@TheKeenMechanic

Жыл бұрын

Thanks for your nice comment. Much appreciated. Although most people won't have the patience to watch the full video I tried to capture the full process for the ones that will appreciate it. Thanks for your time buddy🤝

@tannerhennessy7223

Жыл бұрын

This is supper helpful as I just acquired a 2011 750li F01.

@TheKeenMechanic

Жыл бұрын

@@tannerhennessy7223 thanks

@hallefranklin2646

Жыл бұрын

Hi Carl, could a drivetrain fault on a tri turbo set up be completly unrelated to egr and caused by vaccum system alone? I had the egr cooler replaced last week (recall) and ever since picking it up from bmw the drivetrain fault pops up on cold engine, power loss when accelerating. Im adament BMW have caused this whilst they worked under the bonnet 😒 They are trying to blame it solely on the turbo- and im not buying it

@thisissparta9

Жыл бұрын

@@hallefranklin2646 Can definitely be caused by vaccum system. The pressure converters and electric changeover valves frequently go bad and they operate the turbine control flap, multiple actuating air flaps and wastegate. Could also be an issue with the vaccum lines themselves, possibly a cracked, disconnected or pinched line. I'd recommend using smoke to test the vaccum lines and a vaccum pump to see if the pressure converters and changeover valves hold vaccum properly.

You may find this interesting - I had the same faults on my 2015 BMW 218d (F45) with 115000 miles. I had the EGR valve changed, but it made no difference. However, there is a recall from BMW on the EGR cooler, which they say may cause these symptoms. I contacted their Customer Services and they sent a breakdown truck to my house and took my car to the local BMW dealership. The EGR cooler was replaced AND the intake manifold was also replaced as part of the recall as the original faulty EGR cooler had also caused damage to the intake manifold. My car now runs great with no faults, and the total cost? NOTHING - all done free as part of the recall!

@TheKeenMechanic

7 ай бұрын

Nice one. It is not very often you hear the good stories like this. This is the way it should be. Not all dealerships are the same so this must be one of the good ones. It also could be the case of too many court cases and they are trying to fix the issue in case the car goes on fire as people can get injured or worse. Glad to hear you got sorted

@WankerZoff

7 ай бұрын

I forgot to mention that the dealer also lent me a BMW 120d X Drive auto while my car was being repaired. And I didn't even have to ask for a loan car - they volunteered it! Thumbs up for Halliwell Jones in Warrington.@@TheKeenMechanic

@TheKeenMechanic

7 ай бұрын

@@WankerZoff Great job. Fair play to them. They know how to do business

Brilliant work, you deserve more subscribers!

@TheKeenMechanic

Жыл бұрын

Thanks buddy. I do it with passion as I love cars. I have just got the same customer's car yesterday for timing chain and guides so will be pulling the engine out. There will be a lot more content coming soon🔧🔩🤝

Actually insane work...

@TheKeenMechanic

Жыл бұрын

Thank you

Great video and commentary- thanks for the effort

@TheKeenMechanic

6 ай бұрын

You are welcome🤝🏻

Going to attempt this on my 530d GT shortly... Have the same cold start poor idle and after replacing glowplugs and module with no effect I'm assuming it must be EGR & Inlet issues. Your video is excellent and will be a big help when I'm tackling mine. Thanks for taking the time to make this video 🤘👍

@TheKeenMechanic

5 ай бұрын

You are very welcome. I am glad you came across my video as I know it will definitely be helpful when working on the N57 engine. Best of luck buddy🤝🏻

@lewisl9257

2 ай бұрын

hi , I'm having the same problem and it's the same car as yours, how did you fix yours in the end? my egr looks fine is it the intake manifold?

@TheKeenMechanic

2 ай бұрын

Did you watch the full video?

Such a great video in depth very thankful for this God bless legend much love❤

@TheKeenMechanic

Жыл бұрын

Thank you🤝🙌🤝

Absolute brilliant video. Well explained

@TheKeenMechanic

4 ай бұрын

Thank you

Love your video i recently had my egr valve and inlet manifold replace on my 520d and still getting the same error message the car runs lovely its annoying to keep getting the same error message. 👍👍

@TheKeenMechanic

6 ай бұрын

Hope you get it sorted🤝🏻

Brilliant video thankyou

@TheKeenMechanic

Жыл бұрын

My pleasure🤝

Very nice job 😊thanks for video🤗

@TheKeenMechanic

Жыл бұрын

No problem. I have at least another 30 videos coming soon on the F10 F11 N57 including timing chains and engine and grarbox removal🤝

Actually I'm owning a BMW 520d getting the same error repeatedly in my vehicle I've seen the total video without skipping a single min, Excellent job man 👌👌 The great part of this video is you haven't replaced any original product and cleaned it in very well manner Marvelous job buddy 👍👍

@TheKeenMechanic

Жыл бұрын

Thank you so much buddy. This means so much to me to hear this video is fulfilling it's purpose. I have about 20-30 more videos recorded showing the full process of replacing timing chains and rebuilding the engine. Hope to see you around and glad to be able to help you🙌

@rmsecureindiapvtltd9213

Жыл бұрын

@@TheKeenMechanic 100% I'll look into all of your videos, I felt so happy to see this video and i really appreciate your work Love you buddy 💖

@TheKeenMechanic

Жыл бұрын

@@rmsecureindiapvtltd9213 🥰🙌

Hello, beautiful and clear video. I probably have the same problem. I hope there are experts like you in the Czech Republic. Please pray for me.😔

@TheKeenMechanic

Жыл бұрын

Thank you. I am sure there will be many like me in the Czech Republic. You have great engineers and mechanics there. Best of luck

@neophytermiky

Жыл бұрын

@@TheKeenMechanic Thank you very much for the codes, they will definitely come in handy.😉

@neophytermiky

Жыл бұрын

Thank you very much for the codes, they will definitely come in handy.

@TheKeenMechanic

Жыл бұрын

@@neophytermiky No problem🤝

Great job. I work at a BMW dealership I change 1 or 2 EGR valves and a cooler every day most of the BMW series even new ones have recall. Because they have issues with the EGR valve and cooler leaking. The old ones are Korean the new parts are from Germany they make new parts and BMW pays all expenses.

@TheKeenMechanic

5 ай бұрын

Thanks for sharing this info. I love it when actual BMW technicians become part of this community and share their knowledge and experience.🤝🏻

@recorobertos

5 ай бұрын

@@TheKeenMechanic you are very welcome! I should be thanking you for making these great videos and sharing them with the world tho I am a car mechanic, but I love watching videos like that in my spare time. You are an awesome mechanic! 😁

@TheKeenMechanic

5 ай бұрын

@@recorobertos I think this is by far the best compliment I have ever received on this channel. I really mean it as it is coming from a BMW technician🤝🏻

@recorobertos

5 ай бұрын

@@TheKeenMechanic it's my pleasure to say that. Other mechanics my not say that because many mechanics are jealous they don't wanna compliment the good and hard work of the other awesome mechanics like you. I have friends and relatives they are all envy because when they were a mechanic I didn't even know how to open cars bonnet and know after 20 years I left them behind they got jealous of me. And when I see someone like you doing all these hard work in a small place and with limited tools I feel like I don't know anything. Because I work at a multimillion euro company with all luxuries 20 different kinds expensive jacks all kinds devices 50 mechanics workers yet still we complain and have difficulty to work sometimes. And no matter how good we are we still can't be perfect we do make a mistakes, mess up and forget something and there will come something new that we don't know how to do it. I have learned lots on youtube and still will learn till the end of our lives. And I am sure someday I will learn from you too 😁 so we as a good mechanica never know appreciate our hard work just be proud because you are real great mechanic!😁

@TheKeenMechanic

5 ай бұрын

@@recorobertos It is not very often I come across people like you, so professional and honest. I am happy to exchange whatsapp or email so we can keep in touch and share some good and bad experience😊

Thank u bro

@TheKeenMechanic

7 ай бұрын

You are welcome

Before at cold start it would sound like crap and rough idle. Then driving it went away. Car drove smooth. Once i changed the spark plugs and oil it started act up. Still had those misfires though prior.

i'm curious, did it it fix your problem ? I've done most of what you showed here (but still have to redo the swirl flap actuator) other things to consider that *will* break : all the power pulleys + crank, accesoiries belt, waterpump, thermostat. These diesel bmw's are superb machines, but all that diesel gunk kills them in time if not properly maintained as you showed. If you have *any* error in the hole thing (glow plug, relay, any sensor really or motor error) , regen won't start ! I've learned the hard way this is *crucial* on these cars....turbo, dpf, egr, manifold, it will kill it all if dpf regen is not working. This video is gold by the way, really impressive good work, well done.

@TheKeenMechanic

Жыл бұрын

Hi, yes, the car was fully fixed with no more issues. The customer is extremely happy and spreading the word locally which has brought me more business. 5k miles later sweet as a nut and fuel consumption is 6.5l/100km or 44mpg UK on longer journeys

Good job. Thanks for the video. Tell me please what did you use to check errors ??

@TheKeenMechanic

21 күн бұрын

@@cristianbataturescu5695 BMW factory software called ISTA+

@cristianbataturescu5695

16 күн бұрын

@@TheKeenMechanic I can't find this ista+ Do you have any idea where can i find to buy ? Im in Denmark country, Europa. Does it come with some hardware adapters something ?

@TheKeenMechanic

16 күн бұрын

@@cristianbataturescu5695 go to ebay.co.uk and type in ista+ You can buy it already installed on a laptop or a hard drive or just the software and install on your laptop

I have a 2011 f10. At idle it’s similar to yours. Sounds like it wants to turn off. Does sometimes. Turns back on idling normal then starts misfiring again. Also get the same warning message.

@TheKeenMechanic

2 ай бұрын

Did you check the parts I show in this video?

Im getting misfires in cylinder 1,4,5,6. New spark plugs. Moved the coils around and injectors. Nothing followed. Good compression on all cylinders

@TheKeenMechanic

2 ай бұрын

You can have a vacuum leak from somewhere

@Angel.snchez

2 ай бұрын

@@TheKeenMechanic so i fixed the issue. Im only getting p052B now. Only thing is at cold start i get surging. After a few seconds it goes away and car drives perfect. No issues.. Doesn’t lag or anything. I checked the cam sensors and both were gunked up. Im thinking maybe they are both bad. Would that cause that code?

@Angel.snchez

2 ай бұрын

Cold start “A” camshaft position timing over retarded bank 1. Ive already replaced both vvt solenoids and flushed the oil.

@Angel.snchez

2 ай бұрын

@@TheKeenMechanic theres no rattling or anything as well. I can do high revs and everything sounds normal.

Hi mate i have been watching your video i have f10 520d having drivedrain issue , i dont want to change the car i love it can i bring the car to you

@TheKeenMechanic

Жыл бұрын

Hi Thanks for reaching out. My schedule is full months ahead so I am afraid I can't help you out buddy. I go into detail in my video which should allow anyone who has basic knowledge and tools to be able to do it. Bear in mind that a lot of cars are remapped and modified nowadays and this makes it more difficult for mechanics to get to root cause. Try some local BMW specialist and I am sure you will get sorted as these are common problems with the N47 N57 engines🤝

Where is your place and how much would you charge to do same service for my bmw 520d 2010 please?

@TheKeenMechanic

Жыл бұрын

Hi buddy and thanks for watching. I get asked a lot this question, I am in Northern Ireland.

Hi, when you replaced EGR Valve, did you have to calibrate it?

@TheKeenMechanic

10 ай бұрын

No calibration needed. Just install and go. Thanks

@paulius5556

10 ай бұрын

Thanks💪

Best video I have seen. I have a BMW F11 525D with the engine N47T. My turbo stop working and the car workshop has installed a new turbo. My car is very slow when I accerate. If I accerate too hard the drivetrain error pops up. It seems to me I have a vacuum problem somewhere in the system. What is your suggestion on how I can find out what is wrong?

@TheKeenMechanic

Жыл бұрын

Very hard to tell from afar. Might be best to bring the car back to the garage where they installed the turbo as they know what they were doing at the time and know the history of the car. By the way I have a lot more content coming on the F10 F11 chassis. I have the engine and transmission out for timing chains so this will definitely be at least 20-30 videos on various things that will cover 80% of these cars🤝

@dinhvanpham8102

Жыл бұрын

@@TheKeenMechanic Thank for your quick response. I hav already made appointment with the garage next thursday. They have not run a diagnostic or tested the car properly after turbo rreplacement. It was my suggestion to them to flush the DPF and run a regeneration on the DPF. Uselly the job for turbo replacement is very big and include cleaning of the vaccum system. The garage did not complete any cleaning operation. The garage price is very high , cost me 3031 GBP. include the turbo. A BMW garage cost 4416 GBP. By the way my car has got a recall from BMW concerning replacement of the EGR and the Egr valve as well. It is free and I should waite for my turn. I find your video very tutorial and it encouraged me to do some research on my own. I am loooking forward to watch your videos.👍

@TheKeenMechanic

Жыл бұрын

@@dinhvanpham8102 Funny enough I was cleaning the DPF yesterday evening and managed to record good footage so it should be a brilliant tutorial

@TheKeenMechanic

Жыл бұрын

It is crazy what garages charge and still not fix the problem. When you pay these prices you want no hassle. I can't imagine how they stay in business with such poor service. I hope they can sort it our fast for you

@dinhvanpham8102

Жыл бұрын

@@TheKeenMechanic What is the partnummer for the gasket bully? I need the same gaskett when I do the same cleaning operation on my engine N47T.

Excellent work. wish i lived close by to bring my car up to get it sorted I have a 535d with an EGR and DPF delete. i noticed that it has a slight uneven shake at idle, I don't know why the car has good full economy though (7.8 l/100km in the city) and doesn't feel lethargic or low on power but that slight unevenness is kinda anoying

@TheKeenMechanic

Жыл бұрын

Thanks for your message buddy. 535d is a great car. This is very impressive economy you are getting by the way. Not sure why it will run uneven at idle. I assume your intake is clean due to your EGR delete. It would be worth checking with the person who mapped out the egr to get his opinion. I am currently in the process of taking the engine and gearbox out for timing chains major service and rebuild. There will be many videos coming🤝

Perfect video 💯 🫡

@TheKeenMechanic

Жыл бұрын

Thank you David🤝

@oxconapopona8307

Жыл бұрын

Please where about in uk are you

@TheKeenMechanic

Жыл бұрын

@@oxconapopona8307 Hi. I am in Northern Ireland. Thanks

@oxconapopona8307

Жыл бұрын

@@TheKeenMechanic have same issue with my bmw series 1 find it difficult to get the right person to fix it

@TheKeenMechanic

Жыл бұрын

@@oxconapopona8307 I hear that a lot to be honest. Very hard to find someone who works with passion and has respect for customer's vehicle as if it is their own. Hope you get it sorted buddy🔧🔩🤝

was it shaking because of the erg valve or heater relay, so you haven't concluded maybe?, these are regular problems on every f10 n57

@TheKeenMechanic

Жыл бұрын

Hi Probably a bit of both but I think more the EGR valve. Every time it tried to open/close it shook the engine quite hard. Car was 100% after the work. Funny enough the customer just dropped the car back to me today for timing chain and guides. Thanks for your message

@markovukcevic6595

Жыл бұрын

@@TheKeenMechanic thank you, we are waiting for the video 🤔

@TheKeenMechanic

Жыл бұрын

@@markovukcevic6595 It will take a while for the video as I am extremely busy at the moment but I think this will be great content to share on the channel as I will have to take the engine out completely and do other maintenance jobs🤝

What brand egr did you use, and did it need adaptation ?

@TheKeenMechanic

Жыл бұрын

Hi and thanks for your comment The customer chose Febi 107784 EGR Valve. No adaptation was needed. 2000miles later the car is running very well with no issues. Hope this helps 🤝

@maierazor

Жыл бұрын

Thanks for your answer, I also did pretty much everything, changed egr, cleaned the intake manifold. Codes that keep popping are: 4933 and 497d.

@TheKeenMechanic

Жыл бұрын

@@maierazor Hi. You will need to have a look at all sensors and find the one causing the problems. It could be MAF sensor, vacuum leaks, damaged hoses etc. Best to go to a specialist if you cant do it yourself as you don't want to waste money and swap good parts. Hope this helps

Where did you buy the nice little moment key?

@TheKeenMechanic

Жыл бұрын

Hi No idea what a moment key is to be honest

@dinhvanpham8102

Жыл бұрын

@@TheKeenMechanic I mean Torque wrench

@TheKeenMechanic

Жыл бұрын

@@dinhvanpham8102 most of my torque wrenches were bought on Ebay or Amazon

hi where are you have this problem and. local garage unhelpful

@TheKeenMechanic

Жыл бұрын

Northern Ireland

i want to do same think on my BMW F11 2012

@TheKeenMechanic

8 ай бұрын

🙌

Hi, I had a lot drive train error messages after a turbocharge crash and even after a new turbocharger is installed I got drive train from 1200- 3000 rpm. I found the map sensor was glogged with oil and carbon. I clean the map sensor with brake cleaner. Use a cloth and put som egr/turbo cleaner and clean the hull where tthe map sensor is installed 5 times. After this clean operation, the drive train error disappeared. The map sensor is supposed to give up to 4 bar pressure for an engine to work properly. Now at last my new car workshop has managed to replace and install a new turbocharger. He use only one day and the turbocharger is working perfectly. I have to replace the booster pressure solenoid and the charger pressure regulator ventile. There are two booster pressure solenoids and two charger pressure regulator ventiles. I am going to replace all four of them. Even the map sensor will be replaced. My car has never been so quick and fast. I am very pleased and happy.

@TheKeenMechanic

3 ай бұрын

Nice to hear a happy end story. Enjoy the car and I wish you many trouble free miles🤝🏻

What can happen if Drivetrain l don’t fix it

@TheKeenMechanic

7 күн бұрын

@@matejoorsos231 You can try and see, let us all know what happens

Where are you based? How much will this entire job cost?. I have similar symptoms. Thanks.

@TheKeenMechanic

Жыл бұрын

Hi I am based in Northern Ireland Thanks

@alexandruneacsu2292

Жыл бұрын

@@TheKeenMechanic damn. I am near Glasgow. Nice great job you are doing:)

@TheKeenMechanic

Жыл бұрын

@@alexandruneacsu2292 No worries. You will find someone local to you🤝. Thank you, I love cars so I work with passion and pleasure. Best of luck

@MsREDCIVIC

Жыл бұрын

Hi, how much would this iob cost on a average? Thanks

@MsREDCIVIC

Жыл бұрын

I am being offered a 535d f10, drives fine, however when hard acceleration it doesn't have full power and the drivetrain message comes up on screen.

I have egr fault should I drive car

@TheKeenMechanic

Жыл бұрын

You can but I would fix it as soon as possible🤝

EGR systems should be binned as all this crap in the inlet side wouldn't be there otherwise. What's more planet friendly, a few grams of emissions, or having to buy a new engine / car?

@TheKeenMechanic

Жыл бұрын

Totally agree. The whole industry and emissions regulations is a total scam. It is costing the average joe an arm and a leg to keep their cars on the road but then a war starts and it is ok for one of the wealthiest countries to start using coal🤯

where are you located?

@TheKeenMechanic

8 ай бұрын

Northern Ireland

@andreitanase8432

8 ай бұрын

@@TheKeenMechanic Far away from London..

@TheKeenMechanic

8 ай бұрын

@@andreitanase8432 No problem. Thanks for appreciating my work🤝🏻

@andreitanase8432

8 ай бұрын

@@TheKeenMechanic i realy appreciating your work .verry nice

I know your are in northern ireland any contact details or if you can just talk to my mechanic

@TheKeenMechanic

Жыл бұрын

Hi Thanks for reaching out. My schedule is full months ahead so I am afraid I can't help you out buddy. I go into detail in my video which should allow anyone who has basic knowledge and tools to be able to do it. Bear in mind that a lot of cars are remapped and modified nowadays and this makes it more difficult for mechanics to get to root cause. Try some local BMW specialist and I am sure you will get sorted as these are common problems with the N47 N57 engines🤝