full rebuild in ONE video! seriously man! I hope this blows up! great content.

@ethanjones774

Жыл бұрын

Hope it blows up 😂

@kodiakfournine

6 ай бұрын

This aged well

@killed_phill796

4 ай бұрын

@@kodiakfourninedid it blow up ?

Is it just me or does this seem remarkably simple?

@tbirdboy

10 ай бұрын

I'm sure the cams and VANOS takes some patience.

@exemch4826

5 ай бұрын

Staying organized seems very important

@regulus8319

5 ай бұрын

@@exemch4826this! My biggest issues came from being unorganized. But hey lesson learned

@sskkkkiiii

5 ай бұрын

He makes it look easy lol

@tatumjohnson855

4 ай бұрын

Doing is easy, knowing is difficult

I wish I had thus much confidence and time to build mine instead of wasting money at a shop

This guy really did the WHOLE thing in one vid! So awesome!

@941garage

Жыл бұрын

Thanks bro, was gonna do multiple parts but it was just easier to do everything in one video.

Good vid. One thing I always do when rebuilding an engine though is just have a paint pen when torqueing down mains, rods, or head bolts. Just in case something happens when doing it you can easily remember where you're at still.

Been wanting to take on a project with this N54 platform. With this information it’s confidence inspiring. Would love it in a 135i e8x

Perfect job Awesome detail outline.

holy shit that was awesome to watch haha, looks insane!

This is very nice bro, greetings from France 🇫🇷

Really good, Impressive Job. Hopefully Runs Perfect.

So satisfying to watch this video

Clean rebuild video 👍

Super dope video bro, you gained a sub today

Looks almost as simple as a Cummins to assemble. It's like a mini version besides the bedplate. Loved the video man, I bet she rips! My poor awd n54 has been sitting for a year lol I can't decide if I want twins again or a single.

@jordy808.

6 ай бұрын

fat single

Great vid man. This answered my question about what rods you went with that I posted on another video. I also went with arp but did oversized studs because the heads came that way. Curuious why you didn't go with a Schrick or Cat Cams camshaft? I was talked out of it but still wish I would have.

Sick video man

This is gold

nice vid ! some notes for high HP n54s taken from other peoples build experience *those cutring gaskets on the n54 tend to leak, stick with oem *9mm arp can lift the head if you run high boost - 11mm with nsl300 is the way to go or OEM *Pinned crankhub is a better design than friction washers.

@941garage

Жыл бұрын

Thanks for the feed back, Watch my previous video, I swapped that cutring gasket out. And yes ik I should have went with all 11mm arp studs and will be swapping those 9mm outs. As for for the crank hub I went with the VTT spline hud, works just as good as a pinned hub.

@joshdornseif3284

10 ай бұрын

@@941garagehow long did it take you to swap it? i just put my built motor in but it has an cutting ring gasket. haven’t started it yet.

How much did you spend and can you make a parts list?

@blazingaura18

Жыл бұрын

@941garage

hi man, very good video, where did you find the technical information for the tightening torques and the different clearances between the elements?

Saw rebuild from engine shop from 4 or 5 yrs ago. He stated he used different size bearing for cylinder 1.

FANTASTIC brro

You are the man

Thanks. I need o do this for my 4 series. Where did u get ur parts.

Awesome

What tools should I invest in for a project 335i? I'm prolly going to single turbo it after maintenance, this will be my first European car once I find a good one.

@941garage

Жыл бұрын

A good torque wrench, torque sockets, inverted torque sockets, timing kit, front main seal tool and engine support bar. Screw drivers long/short, mostly just the basic tools. You will buy what you need along the way lol.

This 🔥🔥

Where do you get your service repair manual? It so hard to find an bmw engine rebuilder here in North Carolina. I have 2012 bmw 335i

What did you torque the rod caps to?

You just saved 3:58 👟 👍🏽

What was the protrusion of the piston above the engine block?

I used the dodge rtv on mine same one they use for the hellcats

That’s what I’ve been trying to tell people if you have mechanical skills then bmw’s are relatively easy and cheap to work on

GL bro

Hey man im curious to know why didnyou rebuild the new motor instead of the old one? Im in the same position now. A friend is offering a running one for 700 bucks but it has a lot of miles. My 335 only has 75k miles on it so i think thats better to repair?

Watd u use for head studs?

I learned you do precise job like this it runs until it falls apart from things other than what you did.

Any links for the parts? Or part numbers?

how much hp can these internals take? how do you close the deck?

🔥🔥🔥🔥👌👍👍👍

Hey, what's your e-torque wrench?

i'd use permatex MotoSeal. Stands up to gasoline and oil and heat much better. same as yamabond, suzukibond, hondabond etc.

As a newbie, I couldn't understand how the crank.bearing clearance was confirmed to be within tolerance. It looked like a piece of paper?

where did you get the assembly manual? been looking for it like crazy

@941garage

Жыл бұрын

i gathered all my info online. there isn't a primary source to everything. basically you have to google search to get your answers

I wish you could build an engine for my 335....such a great car

Awesome video brother, what camera and editing software are you using?

@941garage

Жыл бұрын

iPhone 13 pro max, and the app I use is called VN.

@dcs-motorsport

Жыл бұрын

@@941garage I use the same phone but for some reason my quality doesn’t come out nearly as good as yours..

@941garage

Жыл бұрын

@@dcs-motorsport check your YT settings, make sure your upload quality is on the highest setting.

never used anything other than bmw sealant to seal the bedplate. how’s it holding up? is it good?

@941garage

Ай бұрын

I Built 3 motors so far, no leaks or issues.

How do you lock the engine in tdc without the the flywheel being on? That’s only thing stopping me from building my spare block in garage

@941garage

10 ай бұрын

You have to take the engine off the stand put your OEM fly wheel on and put the locking pin in. So basically I did the timing off the stand.

You installed the valves, especially the exhaust valves without lapping?

@941garage

10 ай бұрын

No, all valves were lapped. Both intake and exhaust

ngl this kinda makes me want an n54

@BmwMe-uh9sy

10 ай бұрын

y would u feel the need to lie anyway

Did you silicone the oil pan to?

@941garage

11 ай бұрын

No, the oil pan has a dedicated gasket.

What are you measuring at 3:40 & where was the smoke coming from 8:18?

@8PSIandUp

6 ай бұрын

He’s measuring the space between the crankshaft and the crankshaft bearings, this is (should be) done with all rebuilt engines to ensure the crankshaft doesn’t get chewed up by the bearings because of lack of oil flow.

Did you really not replace the exhaust valves? I definitely would have just for peace of mind

I need rebuild manuel of n54b30a plz

How much did all this cost you?

14:10 what is that tool called ?

Usually you wanna put the piston cooler nozzles after you have the rods in so you don't accidentally hit one.

What’s the tire setup on the car man?

@941garage

Жыл бұрын

245/40/18 front, Toyo r888r 275/40/17 rear.

@christianmaximomolinagarci6190

Жыл бұрын

@@941garage appreciate it man love the build 💪🏼

How do you know when those Apr studs hit bottom 😂

15:25 bro why you ask 160 and do 360?

Scariest thing for me is the timing not sure how hard that is

is this a reupload?

@941garage

Жыл бұрын

Yes, had to take it down do to a copyright issue.

Fancy t wrench

I had no idea you could find N54's at the junkyard

@Thomas998822

10 ай бұрын

Move out of the country. Here in Atlanta there's a few dozen junk yards, and at least 5 pick and pulls. I see N54s come through pick and pull all the time.

Where your 9mm bolts too short?

@941garage

Жыл бұрын

No, but I might switch them out to 11mm soon.

@juanpablodiazguillot3325

Жыл бұрын

@@941garage why the 9mm are no good? but still better than oem right?

@941garage

Жыл бұрын

@@juanpablodiazguillot3325 i heard from engine builders that they are worst then oem. not enough thread. but i have not had any issues so far at 33psi.

I have a n54 Would you build my motor?

Can you build my motor for me

That wasn’t 160 degrees… that was 360… 😢😢

@941garage

11 ай бұрын

Did I say 160? 😅

If your building for 1000+ hp should you just go for a swap? I heard horror stories of N54 guys blowing up their fully built engines at 8-900whp.

@yahyahasan335

Жыл бұрын

the head is pretty restrictive from what i know so getting that hp level is difficult

And what are you going to do now that you have changed the distance between camshaft and crankshaft.... those are not supposed to be cut in any way

using rtv on the bedplate was very questionable

@941garage

4 ай бұрын

I built 4 motors so far using rtv on the bedplate, no leaks or issues whatsoever. I don’t see a reason for spending and extra $200 on some sealant.

What do u do for work? Just curious. This equipment and all your mods are not cheap whatsoever. Just tryna get to a similar spot so I can work on engines all day.

@wth_iswrongwityall

Жыл бұрын

We still wondering bruh? We tryna get right like you.

@BumpTune8462

Жыл бұрын

@@wth_iswrongwityall idk I guess it was insulting. I’m getting through a bmw technician school and I wanna use my skills in the performance industry or at least building cars to some degree.

@941garage

Жыл бұрын

@@BumpTune8462 nah your good man, I’m a tile installer. I just do this for fun on the side, maybe one day this will be my full time job lol. Work hard brother because in the end it will be worth it.

@bombombimbim440

Жыл бұрын

Yeah.... Bmw 6cyl engines is very expensive and complex, average workers or even middle class rarely can afford this cars!!! Bmw engine even more expensive than v8 Ls3 chevy for maintenance.....

@aaronmayorga9621

Жыл бұрын

@@bombombimbim440 i believe that , i blew up my turbos on mine lmao

You can sell this in Netherlands for €6000

No assembly lube is insane.

Athena headgasket ? Get ready to rebuild your engine again.

@941garage

Жыл бұрын

Watch my previous video I swapped that gasket out.

I probably would have gotten new valves

@941garage

Жыл бұрын

why?

Can you build mine

@mogulme6190

Жыл бұрын

You don’t think you could do this?

All that work just to throw on VTT parts. You’re gonna regret it. That hub is gonna destroy your whole build

@941garage

6 ай бұрын

That’s where your wrong, spline lock hubs have been proven to hold abuse from high hp builds. Mine is still holding up just fine.

@itb1820

6 ай бұрын

@@941garage until it doesn’t. You’ll learn soon enough.

@941garage

6 ай бұрын

@@itb1820 they have proof that the hub is able to withstand crazy torque numbers beyond what the car is able to produce, this is a solid design. Your just looking at who made it but not how well it performs or how it’s designed.

@itb1820

6 ай бұрын

@@941garage I would say how much did Tony pay you. But Tony would never pay anyone for anything. You’ll find out soon enough

I’ve rebuilt my engine with pistons, head gasket, turbo, ignition coils and spark plugs. No leaks engine spins over but won’t start 😢 I’ve pulled all the codes but nothing that should keep it from starting Help 😢😢 Car Scanner ELM OBD2 Version: 1.101.9/1.101.9/iOS DTC report Connection profile: BMW OBD-II / EOBD F-seriesDate: 1/8/2024 4:58:09 PM VIN: WBA3A5C50CF34xxxx ============================ OBD-IIOBD-II DTCs: 7 ---------------------------- P0030 [0x0030] Heated oxygen sensor (HO2S) 1, bank 1, heater control - circuit malfunction HO2S Heater Control Circuit Status: Pending ---------------------------- P1338 [0x1338] Archive (inactive) #8 MISFIRE CIRCUIT - OPEN Status: Permanent ---------------------------- P0366 [0x0366] Archive (inactive) Camshaft position (CMP) sensor B, bank 1 - circuit range/performance Camshaft Position Sensor "B" Circuit Range/Performance Status: Permanent ---------------------------- P0036 [0x0036] Archive (inactive) Heated oxygen sensor (HO2S) 2, bank 1, heater control - circuit malfunction HO2S Heater Control Circuit Status: Permanent ---------------------------- P0597 [0x0597] Archive (inactive) Thermostat heater control system - open circuit Thermostat Heater Control Circuit/Open Status: Permanent ---------------------------- 138104 [0x138104] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed, Test failed since last DTC clear ---------------------------- 12B104 [0x12B104] Status: Pending, Confirmed, Test failed since last DTC clear, Test not completed during this operation cycle ============================ Engine control unit No DTC found. ============================ Transmission control unit No DTC found. ============================ SRS/Airbag No DTC found. ============================ DSC/Traction controlDSC/Traction control DTCs: 2 ---------------------------- 480A13 [0x480A13] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed, Test failed since last DTC clear ---------------------------- 480A14 [0x480A14] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed, Test failed since last DTC clear ============================ CAN gatewayCAN gateway DTCs: 1 ---------------------------- 801C20 [0x801C20] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed ============================ Fuel pump No DTC found. ============================ Suspension/Dynamic management No DTC found. ============================ TPMS No DTC found. ============================ ABS/DSCABS/DSC DTCs: 2 ---------------------------- 480A13 [0x480A13] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed, Test failed since last DTC clear ---------------------------- 480A14 [0x480A14] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed, Test failed since last DTC clear ============================ Steering No DTC found. ============================ Car access systemCar access system DTCs: 2 ---------------------------- 804182 [0x804182] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed ---------------------------- D90D06 [0xD90D06] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed ============================ Center roof module No DTC found. ============================ Gear selector switch No DTC found. ============================ Dashboard/Instruments cluster No DTC found. ============================ Infotainment systemInfotainment system DTCs: 4 ---------------------------- B7F80F [0xB7F80F] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed ---------------------------- B7F850 [0xB7F850] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed ---------------------------- B7F8CB [0xB7F8CB] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed ---------------------------- E1C444 [0xE1C444] Status: Test failed (current drive cycle), Pending, Confirmed ============================ Central electronics No DTC found. ============================ Driver's seat No DTC found. ============================ Central module (in driver's footwell) (FRM) No DTC found. ============================ Climate/heater/Air conditioningClimate/heater/Air conditioning DTCs: 1 ---------------------------- E7146F [0xE7146F] Status: Test failed, Test failed (current drive cycle), Pending, Confirmed, Test failed since last DTC clear

@Han-cq4ug

Ай бұрын

Did you end up figuring it out?