Thank you for using the best camera angles and videography editing. I also appreciated just watching the process without the symotanously step by step verbal distraction .

Excellent video; very helpful. One tip if I can add. Reattach the ground wires before installing the ignition coils otherwise it is hard to put the small nuts in. Put a rag in the spark plug cavity to prevent the nut from falling into it. Also, when removing the cover bolts, stuff a rag between the engine and the body to prevent bolts or washers from falling down.

This is just the video I needed. I bought a 2002 530i that was disassembled for a wiring harness replacement. This video helped so much putting it back together showing where everything goes. Thank you!

Thank you for making such a great and clear video! I've watched a few others and there is so much subjective sidetalk I cannot concentrate. Yours is much better with some great camera shots. I just got done doing this in my garage, and everything went exactly you showed. I took a nice long test drive and no more leaks!

@msbrunell

Жыл бұрын

Glad it was helpful!

Thanks for showing the bolts! I almost bought 15 of the same one before realizing it is 11 of the same on the edge and 4 different ones in the center. Most videos skip over that part despite non-stop talking.

@msbrunell

Жыл бұрын

Glad I could help!

Brilliant video - great camera work!

Thank you so much for making such a clear, concise DIY video. New sub here!

@msbrunell

2 жыл бұрын

Glad it was helpful!

Perfect tutorial man! Thank you very much!

Fantastic video man! Super helpful

this deserves more views.

Excellent, super-helpful video. Thanks so much!

Makes a change that there is no annoying crap playing in the background, Good tutorial video,

Very good manual. Many thanks.

Excellent, concise video. thanks

Thanks for the video... Awesome... A not talking guy doing things right.

Great video. My old gasket was so brittle it was stuck in, got it out using a heat gun. Also be careful for those air lines you take out below the spark plugs, those can be extremely brittle.

@msbrunell

3 жыл бұрын

Yes you are right...they are very brittle. Of course so are many of the engine parts, like intake boots.

good job very helpful thank you very much

Golden. Thank you !

Job well done

Very helpful!

Do cover seal washers have to be replaced in all cases? Thanks very much for this video. It is thorough and to the point

@msbrunell

3 жыл бұрын

I would think that if the washers are flexible and soft, you could reuse them. But mine were brittle and hard.

I just replace the valve cover gasket on my E46 went to turn it on was idling fine for a minute and all of a sudden it started to have a rough idle and check engine light turned on I have codes p0313,p0174,p0102,p0171 what could it be ? The car runs and drives decent but I do notice it chokes a bit when I press the throttle..... oh and my car was running perfectly fine before doing the valve cover gasket what could it possibly be ? Maybe I broke a ccv hose I replaced the vacuum line that goes to the secondary air pump but it still has a check engine light .... I also noticed when I went to drive the car i noticed a hissing noise almost like a vacuum leak that wasn’t there before also to mention when disconnecting the ccv hose it sounded so brittle and made a cracking noise as I slightly pulled it back

is it pretty much the same with m54b22 ?

Great video. Any issue with using brake cleaner on the plastic valve cover though?

@msbrunell

3 жыл бұрын

None. You could use some water-based degreaser instead.

Cuanto de torque

Where can I find torque specs and sequence for the 2002 e39 525i??

@msbrunell

2 жыл бұрын

Select CC, which will show the info.

Great tutorial! I did this yesterday! I may attempt the oil filter housing gasket as I know you have a vid on this too, how difficult is it? @msbrunell

@msbrunell

3 жыл бұрын

If you have the e39, then dealing with the fan shroud is a lot different than for the e46 (which most videos are based on). For the e39, follow the video I made and it should be OK. Consider getting someone to help you when putting the fan back on. Otherwise, all of the engine stuff (nuts and bolts) is very straightforward. Have fun!

@kabethell

3 жыл бұрын

@@msbrunell yes it's the same as yours e39 530i m54, okay thanks I'll give it a go I think! 😁👍🏼

@msbrunell

3 жыл бұрын

Unless you need to, I wouldn't open the cooling system...it will make the day a lot longer.

Why no seal gasket?

@msbrunell

2 жыл бұрын

None needed

Excellent. Thank you very much for the video and more creativity. Clean service and very accurate and perfect photography. Thank you K B K B قبل 5 أشهر Great tutorial! I did this yesterday! I may attempt the oil filter housing gasket as I know you have a vid on this too, how difficult is it? @msbrunell msbrunell Scott Link Scott Link قبل 6 أشهر Excellent, concise video. thanks