Nice fix but a lot of wheels will clear with no problems enjoy your videos thanks

@dtperformance256

Жыл бұрын

@allen cobbs good to know!! Thanks for commenting! I was curious why there weren’t a video or more discussion on this issue yet.

As an update to those wanting these spacers, they are not available in 6mm anymore. You can get 3mm or 5mm now.

@dtperformance256

23 күн бұрын

@yourpcmd Thanks for sharing my friend!! Many thanks for the views, comments, and the Super Thanks!! Much appreciated brother!!

Great detailed video.. I did this brake upgrade to my gbody a while back and good thing I haven’t really driven it yet.. I always thought the front wheels had a tad bit too much drag for my liking and now u confirmed my suspicions.. I’m gonna go ur route to remedy it.. u earned my subscription! 🫡

@dtperformance256

8 ай бұрын

@nitomeanbodyGBODY. Hate that you had the issue but glad the video helped. I had not heard of anyone having scrubbing but it was obvious when I took the wheel off the caliper bracket was touching a little. I really appreciate the sub and the comment for sure!!

@nitomeanboyGBODY

8 ай бұрын

@@dtperformance256 I believe that it’s so minimal most don’t bother. But I knew I couldn’t be crazy to think it.. but because I hadn’t heard anyone else complain I just figured maybe the slight drag was just the hubs natural design. But now i know better from the light u shed on it!

@dtperformance256

8 ай бұрын

@nitomeanboyGBODY I can’t live with that kind of stuff. Drives me nuts.

If you run NHRA sanctioned events you may need those open end lug nuts to pass tech.

@dtperformance256

Жыл бұрын

@Steve A thanks for clarifying! I was wondering that and that is why I kept the open end lug nuts. I read that if you use a spacer NHRA requires that you lengthen the stud the same amount. I kept the open end lug nuts to show the lenght of lug nut that I have installed. Thanks again for the comment!!!

Different wheels with different offsets will clear the caliper bracket with ease. Of course not everyone is able to get a set of different wheels but i think it's the best solution so one does not have to improvise lol.

@dtperformance256

Жыл бұрын

@T0712096 agree but it was cheaper for me to get spacer than new wheels this time. Thanks for the comment and thanks for watching!!

Good tip. Just ordered a set of spacers because they only had 3 sets in stock.

@dtperformance256

Жыл бұрын

@Your PCMD I am thinking I will order a set of 1/2” spacers to have on hand to give me a little more clearance. I don’t know why. I like a little extra room I guess.

Little secret about the original lugnuts, if your studs are shorter than your studs, the end caps pop off letting the stud extend past the end of the nut. FYI

@dtperformance256

11 ай бұрын

@garypease7414 Thanks! I had one push the end off of a lug nut one time and wondered if that was part of the design. Thanks for watching and the comment!

Grinding a little bit off of the abutment bracket where it scrapes the rim would be my low cost solution. Free!

@dtperformance256

Жыл бұрын

@ronnelson7828 I thought about that, but I am an overthinker and thought “what if” the wheel bearing wears later will it damage the wheel? Would I compromise the strength of the abutment bracket? So…….. I over engineered a solution. Crazy I know, but I wanted a repeatable, “bolt on” solution. Thanks for watching and the comment!!

I think that's the rotor for the front.. maybe wrong but maybe

@BowtieMarco

4 ай бұрын

Great video tho!!

@dtperformance256

4 ай бұрын

@BowtieMarco it is the front rotor. It was rubbing my Weld wheel. Have you ever seen that before? That is why I used the spacer. It was crazy. I have never seen that before. And thank you! Thanks for watching and commenting!!

Everybody I see do this upgrade on a g-body never use the backing plate/ dust cover & they didn’t have that problem 🤷🏽‍♂️

@dtperformance256

10 ай бұрын

@shadetree5346 I have never installed Weld wheels on an S10 Blazer but I would have expected the fitment to have clearance. I see Blazers all the time with Weld wheels. I tried researching this and I am not sure why my wheels were touching on the back. It was an odd thing and this was my solution. Wanted to share the video in case someone else had seen this as well. So far I haven’t had anyone else say they had the same issues that I had. Maybe they have and just aren’t commenting. This fixed my issue but it it still odd to me that I even had an issue. Thanks for watching and the comment.

Use a spacer.

@dtperformance256

2 ай бұрын

@Air-ei9qb Correct ….I had to use a spacer. Thanks for watching and commenting!