Want to convert your Mobula 8 to a 4K Cinewhoop? Check this: kzread.info/dash/bejne/iGuF08dslM-nlLA.html

Dude thanks for the video it's much appreciated just got the mobula 7 today and you have saved me heaps of hours lol it's appreciated

@iFLYXWings6589

2 сағат бұрын

Glad this help~~ This is the reason why i am sticking with beginner tutorial contents

SPI receivers DO NOT support D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) Modes (Packet Rates) and thus will not bind or sync with a TX module in any of these modes. This helped for me to bind Boxer, because default was F1000.

@andrecook4268

8 ай бұрын

This was what was stopping mine from binding - thanks! Hours of fiddling!

@sa1nts1n

8 ай бұрын

Wow! Thanks a lot! I spent 2 hours trying to bind my remote :/

@centralrif2058

6 ай бұрын

Had to setup Packet Rate to 250Hz in lua erls script on my Radiomaster Pocket - bind successful

@ulungprabowo

5 ай бұрын

​​@@centralrif2058hello what else I should know in setting up the mobula7 for Pocket? I am still waiting mine in delivery.

@centralrif2058

5 ай бұрын

@@ulungprabowo hi! there was just 1 thing - correct Packet Rate, mobula 7 2.4G ERLS works just great with radiomaster pocket erls

Thank you! I'm a complete newbie to this and your video helped me a lot.👍

@iFLYXWings6589

9 ай бұрын

Glad it help. Happy flying

This is the 1st video I've seen where it actually tells me what I need to do

@iFLYXWings6589

10 ай бұрын

Glad to know the goal of this video succeeded

VERY helpful thank you straightforward to the point no BS worked the first time. subscribed

@iFLYXWings6589

10 ай бұрын

Glad it help! Thanks for the support

Thanks for the info, haven't bought the whoop yet but will definitely come watch again when I do!

@iFLYXWings6589

11 ай бұрын

Thank you ! You will love this one ☝️

Thank you!

@iFLYXWings6589

10 ай бұрын

You're welcome!

thanks!!!

Thanks

Short to the point everything u need nothing you don't great vid

@iFLYXWings6589

Жыл бұрын

Thanks !

thank you very much for this bro it really help🤙🚀✈

@iFLYXWings6589

10 ай бұрын

Glad it helped !

That was very helpful, thanks!

@iFLYXWings6589

11 ай бұрын

I’m glad it helps !

핵심만 설명해 줘서 고마워요.

@iFLYXWings6589

11 ай бұрын

Glad it helped!

and if all this fails, try going to CLI, typing bind_rx, have the controller ready to bind, press enter on CLI first and then bind on the controller and Voila, but do everything he said first :)

Very informative and helpful video, do you have a guide how to bind Radiomaster pocket to Mobula7 or 8?thanks in advance for your response.

@iFLYXWings6589

8 ай бұрын

Thank you, sorry, have not received the pocket yet but the terminology should be the same. Will be doing a series of video to demo the setup

Excelent! Bought a Mobula8 with Frsky Rx option. Can I simply bind to my Zorro Tx?

@iFLYXWings6589

7 ай бұрын

If you Zorro TX is Frsky or 4in1 then yes

@woutersmith7616

7 ай бұрын

@@iFLYXWings6589 Thanx👍🤠🇿🇦

All works fine for me in betaflight but then in reality drone motors dont move, so no arm, disarm, etc. Any idea? Binded mobula7 to jumper tpro v2 elrs thanks in advance

Have you got the factory board hex please, only the red leds are showing on fc now. I need to put it right back to stock.

@iFLYXWings6589

2 ай бұрын

Sorry, i don't currently have it, but you can try finding it on the happymodel website

Will this work for a mobula 6 elrs (not hd) too? I'm struggling to find a specific video for my new Mob 6. Thanks.

@iFLYXWings6589

6 ай бұрын

If your FC board is also the X12 then yes it will work

Great video. How do i find the binding phrase on the tx12? I dont know what to enter into beta flight since i cant figure out what the binding phrase is on the tx

@iFLYXWings6589

7 ай бұрын

The binding phrase on your TX12 will need to be setup by yourself, suggest to check out my TX12 guide kzread.info/head/PL8oE9qQrTLtcWcmj19GB0Zp7ahm3Dvv2P&si=eCtw_TEbZo6X_YwA

@lh7801

7 ай бұрын

@@iFLYXWings6589 thanks bro I'll check it out. Keep up the good work

I am new to the hobby and watched your videos about TX12 MKii and Mobula 7 binding videos, but I can't manage to get it connected through the method you showed in the videos. The video itself is super clear, but after I set the binding phrase through the wifi option in TX12, and Betaflight it just did not response. Any idea of where should I look for the issue?

@iFLYXWings6589

10 ай бұрын

Please confirm your Mob 7 has been flashed to BF 4.4 or above ?

@xw2672

10 ай бұрын

@@iFLYXWings6589 Yes, it is updated to BF 4.4.2, the same as this video showed. I am using TX12 MK ii, and is 3.0.1 firmware, I just can't figure out why this is not binding. Do you have any clue of where should I be looking for?

@lterl3288

9 ай бұрын

@@xw2672 "D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) modes (package rates) are not supported by SPI receivers, and equipment in this mode will not be able to combine with an SPI receiver." This setting is in the elrs script on the transmitter (f1000 is installed on tx12 by default). Write if it helped.

Hello would it be possible to flash the new hummingbird v3 to 2.5 in order to bind to my elrs zorro on 2.5?

@iFLYXWings6589

10 ай бұрын

Good question, by theory, yes, but I don’t own or have owned a newbeedrone quad before. If I remembered correct NBD has self developed software ?

I was able to bind it but arm switch does not work under modes Aux 2 for acro/ horizon works fine Aux 3 for turtle works fine , but Aux 1 does not work , but if I change Chanel 5 which is my arm switch h to the opposite direction it works in beta flight. I believe there might be an issue with the board

@iFLYXWings6589

9 ай бұрын

Nope, your board should be fine, double check your settings

hey i just tries to follow this but my reciever settings arent saving? im also missing all of the elrs relation commands in the cli tab. please help haha

@iFLYXWings6589

6 ай бұрын

Please provide more details, please confirm you have the analog version

I have a mobula7 1s elrs 2.4g drone and a radimaster tx12 MK2 ELRS. When I try to bind them, the image of the drone makes a coup, but does not connect. Bind phrase also does not work. Everything is updated to the max version. Any ideas how to fix it?

@iFLYXWings6589

8 ай бұрын

That doesn’t sound right, if you binding phrase is set up correctly both should have been bounded directly. Can you confirm you Mob 7 is BF 4.4 or above ?

What if you don't have a binding phrase to ELRS? Can you hit bind receiver on beta flight and hit bind on your controller?

@iFLYXWings6589

6 ай бұрын

Yes, as long you have the same ELRS version

Thanks mate! I thouhgt something is wrong because elrs wouldn't create wifi...

@iFLYXWings6589

10 ай бұрын

Glad it helped ! Yes the mob 8 is using a SPI board

I fly on CRSF daily, and find ERS so frustrating. Imagine: pure field, no wifi, no computer and friend left me a drone. How can can I bind it offline? Is it not a disaster?

@iFLYXWings6589

5 ай бұрын

Well ELRS does have a initial learning curve but once you understand it, it becomes quite easy

flashie mi bassline, si va bien despues sigo con el mobula 8 que tiene la misma controladora de vuelo, solo que yo le puse walksnail hace unos minutos...por las dudas sigo con la 4.3.1 hasta comprobar que no falla el spi elrs 3.0.

@iFLYXWings6589

9 ай бұрын

Which FC are you using? X12 or Crazy F405? Depends on which one your ELRS flashing method my be different.

I messed up on binding my Mobula8 can you tell me how to reset the Mobula 8 to factorl settings

@iFLYXWings6589

6 ай бұрын

Yes, you can go to the Happy model website to download the CLI files for the mob 8

So I still do not have the box for the binding phrase...Can you please help? I went through all the steps you showed

@iFLYXWings6589

7 ай бұрын

Please confirm you have flashed the bf version to 4.4 and select SPI ELRS at receiver tab and hit save

@jousiff91

7 ай бұрын

@@iFLYXWings6589 so I just double-checked but so some reason in the log of BF it says "failed to open serial port". So it didn't flash the new 4.4 firmware.

How can I update the receiver to ELRS 3.3.1? My transmitter also has ELRS 3.3.1. Both have to be on the same level, right?

@iFLYXWings6589

8 ай бұрын

If you have a SPI ELRS receiver, this video should explained the steps, also as long you RX & TX are both in 3.X you are good

@fliegerdieter2843

8 ай бұрын

Ah OK Thank you@@iFLYXWings6589

Tim, The Mobula that I bought from Banggood don't have any Data. How to get them?

@iFLYXWings6589

8 ай бұрын

Here’s the link for the factory default CLI dumps. Check to see if you find the one you need If not, e-mail me I’ll send you my presets www.happymodel.cn/index.php/2023/05/05/default-factory-dump-file-for-mobula8/

@Asian_Jewelry_International

8 ай бұрын

@@iFLYXWings6589 I have nothing in my back up what so ever only says default nosave. My first time doing this, my ELRS Boxer won't connect to my wi fi either. This is complete mess, I did go to edge tx and could not find the smt somthing to update the firmware.

I had to send mine back, rx defected. Spi rx are not so good apparently

@iFLYXWings6589

Жыл бұрын

This is the problem with AIOs ….convenient but when something breaks …bye for the whole unit

Hi followed your instructions but I keep getting"No response from bootloader, programming: FAILED, when trying to flash ?

@iFLYXWings6589

8 ай бұрын

You can try to force the board to go into boot loader mode by pressing the FC button and plug in the USB cable, it should fix you problem

@karlc9773

8 ай бұрын

@@iFLYXWings6589 where is the boot button on the mobula 8 ?

Bonjour jai commande un mobula 9 en spi frsky faut il achete un recepteur suplementaire ou est il directement integre merci

@iFLYXWings6589

7 ай бұрын

Sorry, don’t fully understand what you mean. If you have a Frsky receiver, you will need a Frsky radio or a 4in1 module

I flashed mobula 8 to 4.4 and after arming, 1 or 2 motors do not spin. What is the problem ? How to check motors? I checked the connectors - its ok. Betafly has a reaction to the motors when the sliders move.

@iFLYXWings6589

10 ай бұрын

Please confirm you have save and loaded your presets after flashing ?

@seriousserg4128

10 ай бұрын

@@iFLYXWings6589 I solved the problem, but I'm not sure of the source yet. To test the drone, I used a 1s battery 660mah, which may not be enough for the initial spin-up of the motors. In the manual on the happymodel website I saw the ESC settings for the Bluejay configurator . There is a significantly higher min start power than the default ). After flashing new values ​​and taken a fuller battery, the motors began to spin up as expected . Joining the FPV is not as easy as I imagined :)

@iFLYXWings6589

10 ай бұрын

@@seriousserg4128 I see, glad that you resolved the issue!

Can the Mobula be bound to a Spektrum (Dx9) radio? Thanks

@iFLYXWings6589

10 ай бұрын

No, I will assume you need a Spektrum receiver

@aenitro

10 ай бұрын

@@iFLYXWings6589 Thanks for your response.

I bought Mobula8, when I try to select SPI Rx and save, it goes back to Serial all the time, what can be the issue?

@iFLYXWings6589

10 ай бұрын

Double check which model you have if its a HD(walksnail/AVATAR/DJI) then the AIO is F405. This board will have a serial based ELRS

@vedmarth

10 ай бұрын

@@iFLYXWings6589 actually I found instructions and its indeed works with serial connection

After flashing the drone, the motors don't start, can you help?

@iFLYXWings6589

5 ай бұрын

Please confirm you have reloaded the presets after flashing.

iv been trying to get my Bassline to bind for over 4 months on and off, iv tried everything and still cant get the bloody thing to bind. Very frustrating. Iv updated the board to the newest betaflight, My transmitter is also on the same firmware, iv tried with and without binding phrases and still nothing. it just sits there blinking red and green. Grrrrrrrrrrrrr!

@iFLYXWings6589

10 ай бұрын

Which AIO board do you have? X12 or F405 ? Reason I’m asking, X12 is SPI F405 is serial. Also, have you plug it into betaflight to check the receiver tab? Any stick inputs ?

@k1ortia

10 ай бұрын

@@iFLYXWings6589 it's the Crazybeef4fSX1280. Which is obviously an spi based board and I have correctly selected this in the receiver tab, then ELRS. I have updated the board to the latest Betaflight firmware, and my ELrs transmitter is on version 3.2.1. If tried binding with a binding phrase and without. Used both 250hz and 500hz nothing. Also tried in hybrid mode instead of wide, nothing. Even took the quad apart to bind manually using the tiny bind button, guess what... nothing. All it does once plugged in or with a battery connected is blink red and green, Which to my knowledge is ready to bind. But nothing at all. I do believe i have a faulty board. If there's something iv missed them I'm all ears. Cheers

everytime i try to flash the mobular 8 it says failed to open serial port. Does anyone know the solution to fix this?

@anthony6745

10 ай бұрын

Same issue

@iFLYXWings6589

10 ай бұрын

Some dump reason maybe the USB cable, some even with the data mark will still not be recognized. Try a different cable to see if it works. Or try to force the FC into DFU mode to see if it works, press the button on the fc and plug in the cable at the same time should do the job.

Any tips for “failed to open serial port” error?

@iFLYXWings6589

10 ай бұрын

Which part are you referring to? When connecting the drone to BetaFlight?

@sltproductions1285

10 ай бұрын

after flashing

How do I do this with the frsky version? I'm trying to bind to my jumlert18

@iFLYXWings6589

9 ай бұрын

For Frsky, i am not so sure. but the general idea is to press the button on the FC or click bind at Betaflight and then hit bind on your Radio. Also double check to see if your protocol is at D8 or D16

@lancekinshella5817

9 ай бұрын

@@iFLYXWings6589 I got it.... switched from d16 to d8 and bound right away

@iFLYXWings6589

9 ай бұрын

@@lancekinshella5817 Glad you got it fixed

When i try to update it says failed to open port

@iFLYXWings6589

2 ай бұрын

1st try a few different cables- this is mostly the issue 2nd if cables is not the issue, run the impulseRC driver fixer to see if it fixes the issue impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe

hi, i had follow all the step and i still got issue to connect my drone to my radio, i bind but noting happend, can i know here i wrong ?

@iFLYXWings6589

8 ай бұрын

Can you please advise what equipments are you using? I need to know the exact model of your drone and your radio to offer you a solution

@coregenesis4630

8 ай бұрын

@@iFLYXWings6589 hi, is ok, I got it fixed, is choose the 250hz in the radio, maybe u can add notes in there, so that can helped more haha, mine using elrs 3, so maybe is the reason need chg the hz

Спасибо👍🤝

tuviste algun problema de rango en el spi elrs 3.0 o funciona bien? tengo miedo de salir de la version 4.3.1 de happymodel y que tenga algun problema... Gracias. Emiliano

@iFLYXWings6589

9 ай бұрын

Nope, i dont recall having a range issue, but depends on how far you are looking. round the house no problem

@siniestrorave

9 ай бұрын

Happymodel support told me officially that the version 4.4.2 will works on analog mobula 8 & analog bassline, always using the x12 FC. They dont recomend 4.5 yet

@siniestrorave

9 ай бұрын

Bueno hoy probé el mobula 8 en el parque y con la versión 4.4.2 el spi pierde recepción a los 40 metros ....así que voy a volver la versión original perdiendo el osd HD...sino tendría que poner un elrs serial...pero x el momento no lo voy a hacer....

@iFLYXWings6589

9 ай бұрын

@@siniestrorave It is completely up to you~Btw if your Mob 8 is HD then you do not need to flash BF, you just need to flash your serial based ERLS receiver ERLS

@siniestrorave

9 ай бұрын

@@iFLYXWings6589 My Mobula 8 came analog and I added a VTX walksnail. I wanted to update to 4.2.2 just to get the HD OSD, but the SPI ELRS range doesn't work properly and I lose the drone at 40 meters. I am going to stay on version 4.3.1 as there are no problems with the SPI ELRS 3.0 unless I add an external ELRS receiver later

I succesfully binded my mobula8 to my controller but when i disconnected the drone with the pc, my radio says telemetry lost and the controller doesnt seem to control the drone

@iFLYXWings6589

9 ай бұрын

Ok.... just want to confirm, have you also plugged in a lipo?

@daniel.91o6

9 ай бұрын

yes i did@@iFLYXWings6589

@daniel.91o6

9 ай бұрын

Ma radio has the 3 bars signs for the connexion but the switches and stuff still wont work@@iFLYXWings6589

i did the exactly same thing and it didnt work =/. I click on bind on betaflight, and when i click bind in lua script, the quad model on betaflight mades a flip and nothing hapens wtf kkkkk, maybe a problem on rx? There is anyway to check it?

@iFLYXWings6589

9 ай бұрын

Did you reloaded your presets? The binding method is based on using bind phrase which is the recommended method, try to set up your bind phrase for both your RX and TX

@lterl3288

9 ай бұрын

"D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) modes (package rates) are not supported by SPI receivers, and equipment in this mode will not be able to combine with an SPI receiver." This setting is in the elrs script on the transmitter. Write if it helped.

@poltergeist6151

8 ай бұрын

do you fix that?

binding phrase box doesnt pop up

@iFLYXWings6589

8 ай бұрын

You need to save and restart

This video is incorrect, because a Mobula8 can come with a UART ELRS. You should specify that in the video otherwise people are gonna try flashing BF when they dont have to with a UART ELRS

@iFLYXWings6589

10 ай бұрын

I agree , this video was made prior of the HD version that came out with a different AIO. Let me update it to analog only

Boa tarde amigo meu drone bateu num galho e rodopiando caiu perdendo sinal com meu radio e nao vinculou mas o que pode ter ocorrido. Meu rádio é ocomando 8 ELRS

@iFLYXWings6589

4 ай бұрын

Sorry, need more details to help you. First, please start with which drone do you have ?

@voosempre.9946

4 ай бұрын

Mobular 8 amigo , até agora não consegui vincular com o rádio depois da queda eu ainda fiz um vôo mas quando coloquei no betaflith ele até deu sinal e depois foi diminuindo e não vinculou mas.

@iFLYXWings6589

4 ай бұрын

@@voosempre.9946 Try reflating the betaflight firmware it should fix the issue

@voosempre.9946

4 ай бұрын

Vou tentar

could you send me the backup file please

@iFLYXWings6589

10 ай бұрын

Can you please email me at piggycraftsman@gmail.com? I will send over the file

I wonder where the binding button is on Mobula 8? I want to bing it manually. Anyone ?

@iFLYXWings6589

8 ай бұрын

It is on your FC the little yellow black dot

@albaniansuperiorshqipetari8055

8 ай бұрын

@iFLYXWings6589 I can't see it. I can see the boot button but not bind button. I. Looking at the mobula 8 manual and the diagram of the FC does not show it, do u have any pic link of the FC

@iFLYXWings6589

8 ай бұрын

@@albaniansuperiorshqipetari8055 the boot button will be your bind button as well. But still suggest you to bind it with a bind phrase

@albaniansuperiorshqipetari8055

8 ай бұрын

@iFLYXWings6589 I got it now I'm just going to bind it from configurator on receiver tab. Thanks for ur help Man

@albaniansuperiorshqipetari8055

8 ай бұрын

I've got it ready to fly now but my eachine goggles are not connecting to the drone, normally I conected them but just Turing power on and search for channels usually it finds the channel easily. This time I can't conect I tried two different eachine goggles, they work fine with my other drones. What do you think?

Can i connect a tx12 with a avata?

@iFLYXWings6589

9 күн бұрын

Nope not possible

@ojama2451

8 күн бұрын

How about a pavo20

Does this work with mobula 6

@iFLYXWings6589

7 ай бұрын

the concept is the same, just the mob 6 has a different FC thus your target will be different

@puc19

7 ай бұрын

ok @@iFLYXWings6589

@puc19

7 ай бұрын

For so,e reason it is stuck on “Initialising reboot to boot loader

@iFLYXWings6589

7 ай бұрын

@@puc19 This happens, what you need to do is 1. Remember which target your FC is 2. Press and hold the button on your FC and at the same time plug in the USB, this will force the FC into bootloader mode, if you do not see "Exit DFU mode" button glow up, try the process again

@puc19

7 ай бұрын

Ok

is this everything I need to do to bind my radio and drone? i'm having some trouble getting them to bind

@iFLYXWings6589

6 ай бұрын

In most of the cases, this will be all you need to do.

Its just not workin now! Regrettin buyin this mob8

@iFLYXWings6589

2 ай бұрын

Sorry to hear this any particular issues?

mine won't bind i tried everything. do i need to program the transmitter too? isn't the binding phrase written in the tx screen? i updated the firmwares i've seen a lot of videos but no one spends a word more on the binding process pls help🥲

@iFLYXWings6589

3 ай бұрын

Yes, you need to program the TX as well. 1. Make sure your TX is also at ELRS 3.X 2. Set up the binding phrase to be same as your TX 3. If you RX is SPI based set your packet rate to 500hz This video will show you how to flash the firmware of the TX How to Flash Radiomaster TX12 MK2 ELRS Firmware To ELRS 3.0 kzread.info/dash/bejne/Z5uJzphrp67gl7A.html