Hell yeah. This is one of the videos that helped me decide on the 85 as my first quad. Nice flying man :)

@alex_k21

2 ай бұрын

Awesome! Thank you!

Great footage buddy, interesting modifications i see bellow on the comments...congrats!

@alex_k21

6 ай бұрын

Thanks 👍

Огонь бро! Хороший пикник

@alex_k21

Жыл бұрын

😁

I have one of these things, and it keeps failsafe thing and dropping out of the sky. How do you have this thing set up in betaflight? I can keep it flying it close range with crystal clear VTX, but for some reason my Little Bitty literadio2 from Beta FPV loses signal. But with the 65pro I can fly that drone pretty damn far away. Any tips?

@alex_k21

Жыл бұрын

I did not change the settings in betaflight, all settings are from the manufacturer. I'm using a LiteRadio 3 ExpressLRS 2.4G remote and it has a good connection. When flying over long distances, the video connection will disappear much earlier, but definitely not the connection with the remote control

Hi! Great video!!! Quick question. I had Meteor 65pro (ELRS) + RadioMaster Pocket Then I bought Meteor 85 (ELRS). I couldn't bind either by button or by a bind phrase. After a long investigation, I discovered that the Pocket transmitter works on 1000Hz, but the Drone 85 only supports 500Hz. So, I had to changes Packet Rate on the Pocket to 500Hz. So, now both my Meteors are connected with the Pocket. Did you have the same issue?

@alex_k21

29 күн бұрын

Hi! I didn't have issues with ELRS connection. My Radiomaster Zorro was connected with meteor through betaflight configurator, when it was with Elrs v2. Now my Zorro has elrs v3 and I use it only with CineLog 25. For my old tinywoops I use Betafpv LightRadio3

@abgamma

23 күн бұрын

To put it into bind mode, you need to remove and reconnect power 3 times.

Вери гуд

@alex_k21

4 ай бұрын

Thanks)

Und wie weit kommst du mit dem Antennen?

😀😃😄

pls do video about your setup and google modification

@alex_k21

6 ай бұрын

I bought a long antenna with RP-SMA connector (Polarisation:RHCP, 5.8G) from an online shop. Unscrew the original antenna and screw on a new one instead, that's all)

What kind of antenna do you have on those goggles?

@alex_k21

10 ай бұрын

Lollipop 4 mini RHCP 5.8G (Long Purple RPSMA)

what is the antenna on the goggles? Is there a difference compared to the stock antenna?

@alex_k21

11 ай бұрын

Antenna -Lollipop 4 5.8G Mini RHCP long RPSMA. Yes, the connection quality is much better if you put the same antenna on the drone (but with a UFL connector). With these antennas, I can fly much farther without signal degradation.

@pawelec8076

11 ай бұрын

@@alex_k21 when you change antenna on the drone, did you have to solder that?

@alex_k21

10 ай бұрын

@@pawelec8076 No, there is an RP SMA connection. you just need to unscrew the original antenna and screw on the new one

how do you atenna swap the goggles?

@alex_k21

6 ай бұрын

I bought a long antenna with RP-SMA connector (Polarisation:RHCP, 5.8G) from an online shop. Unscrew the original antenna and screw on a new one instead, that's all)

Is this the elrs version?

@alex_k21

11 ай бұрын

Yes, Elrs

how to swap the antenna on the drone tho...?

@alex_k21

6 ай бұрын

buy an antenna with the appropriate polarization (RHCP) like on a helmet and a corresponding connector (UFL), remove the old antenna, install a new one

Как дальность с этими антеннами?

@alex_k21

2 ай бұрын

Качество сигнала значительно лучше чем со стоковой антенной. Дальше 200 м я не летаю, но залетая за дерево помех значительно меньше, на оригинальной антенне можно потерять дрон в 50м за деревом

Frsky + analog? (From Cetus series)

@alex_k21

6 ай бұрын

elrs + analog (VR03 FPV Goggles from cetus x kit, Betaflight FC)

@ivankoreshkov5140

5 ай бұрын

@@alex_k21 спасибо 👍

How to make Meteor85 FPV drone with Runcam Thumb camera on top? can you take a video :)

@alex_k21

11 ай бұрын

The camera is attached with three plastic ties - one long one through the canopy, and two short ties attach the camera mount to the first tie. The camera is powered by the flight controller. I soldered a connector in the corner of the flight controller to the 5 volt pins next to the buzzer pins. If necessary, the camera can be turned off and removed from the drone.