👏 👏 for doing that back of the belly on the ground like that, that’s some tricky Shit

@thecadillacdanshow8658

9 ай бұрын

It really sucked I dont plan on doing it again..looking back I should have just done a full frame for this car but it has definitely held up great I beat on it every time I drive it and even sometimes when I dont drive it

Congrats on hitting 1k ur catching up to me

@thecadillacdanshow8658

2 жыл бұрын

I'm getting there

Awesome video once again I need to do this

Congrats on 1k

Great video!! I love your content!!!

@thecadillacdanshow8658

2 жыл бұрын

Thank you

Keep the videos coming 👍🏼

Thats hard work right there good job

@thecadillacdanshow8658

Жыл бұрын

Yeah it's a bit of a pain but definitely doable!

Love the video

@thecadillacdanshow8658

2 жыл бұрын

Thank you!

Well Done Brother

@thecadillacdanshow8658

2 жыл бұрын

Thank you!

u weld good it's just that will still crack if it's done like that

@thecadillacdanshow8658

Жыл бұрын

Where would it crack? I have never had any issues even on hoppers

Heyyyy

Hey brother I have a question what is the thickness of the steel you use on the belly also the lower a arms I want to pick up the steel today so I can get started

@thecadillacdanshow8658

2 жыл бұрын

I used 3/16

Sorry, got a small question. Are you doing mig with gas or flux core? Do you weld different depending on the area or part or what you are able to afford or what's easier? Again, thanks for the awesome video.

@thecadillacdanshow8658

2 жыл бұрын

I use gas 75/25 mixture with .035 solid wire as far as welding differently yeah it all depends on what I'm doing most the time I so cursive e's sometimes I whip it back and forth sometimes I just run a straight bead just depends on what I'm doing

@camefromnuthin6994

2 жыл бұрын

I used gasless flux core from blue demon

@thecadillacdanshow8658

2 жыл бұрын

@@camefromnuthin6994 how does it do?

@camefromnuthin6994

2 жыл бұрын

@@thecadillacdanshow8658 it works really good I haven’t had any issues yet

Crossmember stress point guy., not a wrap

@thecadillacdanshow8658

2 жыл бұрын

Only thing missing is the top that's pretty close to a wrap

Have you ever done reinforcements above the lower a arms between the coil? I'm starting to get a crack there.

@thecadillacdanshow8658

2 жыл бұрын

Where the arm bolts to the frame? If so yes I cut out plates and welded them in

how do you feel about splitting the belly? to release all stress??

@thecadillacdanshow8658

2 жыл бұрын

I did it on my oldsmobile I was building it to be a hopper but I dont really see it being worth it for a street car

@phreaktor

Жыл бұрын

@@thecadillacdanshow8658 What do you mean by “splitting the belly?”

@thecadillacdanshow8658

Жыл бұрын

Usually it's done when building a hopper you cut the center crossmember of the frame along the top and the front and rear and stretch it open then add a plate of steel in the opening it changes the geometry of the springs and cylinders also makes the bottome of the crossmember a little higher to help from bottoming out

What kind of oil do u use in your hydraulic pumps from what store

@thecadillacdanshow8658

2 жыл бұрын

For a street setup I use non detergent 30 weight just form any store

@aaronmendez5025

2 жыл бұрын

@@thecadillacdanshow8658 ok thank you

@aaronmendez5025

2 жыл бұрын

@@thecadillacdanshow8658 I have a 3 pump 8 batteries set up how much 2ga wire will I need for batteries and pumps

@thecadillacdanshow8658

2 жыл бұрын

@@aaronmendez5025 I normally buy a roll from the welding shop and there will be a little left over depending on how far you have everything apart

@aaronmendez5025

2 жыл бұрын

Ok thank u so much I really appreciate you For helping me and quick response back

1k

How much do you charge for this?

@thecadillacdanshow8658

2 жыл бұрын

350 for the front and bottom of the belly