I needed to make 90+ medium bee frames to feel comfortable going into Spring. They sure are a lot of work as you will see.
Жүктеу.....
Пікірлер: 130
@paquitalysao92057 жыл бұрын
the best video for making frames. thank you
@CraneofBoulogne6 жыл бұрын
Great video, very informative; exactly what is needed to make my own frames. This is clear and easy for my old eyes to see what needs to be seen.
@billymarkwell11052 жыл бұрын
Thank you...........I've searched KZread for an hour looking for exactly what your video shows.......thank's.....
@IceManTX69
2 жыл бұрын
I'm glad it has helped you. There are many things in the video I wish I could have done better so I'm always glad to hear when it has helped someone. Interested to see how your blueberry mead turns out!
@pcelarskaradionicaopgninko62965 жыл бұрын
Amazing tool. Really nice work...
@hlkotzehendrik7198 Жыл бұрын
Nice. I used the jointer plain for the bee space on the side. Made it a bit higher too, so bees have more working space. Well presented very practical. Thanks
@IceManTX69
Жыл бұрын
Thank you for your contribution!
@jerryconway82207 жыл бұрын
Like the pipe!
@mikeoxlong3224 Жыл бұрын
Tools to make boxes and frames. chop saw, jointer, tablesaw, dido stack and nails and glue.
@olddave48337 ай бұрын
great job and great instructions
@douglashatfield56765 жыл бұрын
good job and yes its fun to make your own equipment
@ricardodominguez37853 жыл бұрын
Great video ! Thank you.
@dadviki78347 жыл бұрын
salut. very very good works man. thankyou.
@josephsastre46410 ай бұрын
Great video. Love your Shop Smith.
@IceManTX69
10 ай бұрын
Hey thanks! Too kind. My mom bought it in 1985 and she built many great things using it. She gave it to me a couple of years before she passed and I have enjoyed learning how to use it.
@baldingsbees57457 жыл бұрын
great video keep up the good work
@valentinalexandru88907 жыл бұрын
hello and thanks for the video! I also made frames and yes, it takes forever... I have a tip for you for making sides : cut the lumber so you have two sides in length , the middle being the top bar. then cut in your jointer the extra wood(the glue sticks) , make the bottom groove, cut them in half, make the top groove and then cut them individually.
@baldeagleApiaries2 жыл бұрын
Wow, big difference after new parts on the band saw. Nice gear for the wood shop. Thanks for the video, I subscibed.
@joesinakandid5283 ай бұрын
While I'm not a "Safety Sally" I'd like to mention that there probably should have been a feather board or two used on the 2 x 4" side piece dado work? Quick and easy to make and having owned and used my Shopsmith for many years I know that I would be using them - especially on awkward, tall, end grain work.
@IceManTX69
3 ай бұрын
Yes, you are correct! I have the plastic SS feather board and I should have definitely been using it. I had got the SS from my mom and only had it for a brief time when I made this video. Learned a lot of lessons in the beginning the hard way and luckily I still have all my fingers. I did some stupid and shady things.....
@user-xc6ps9qb2i6 ай бұрын
Станки у вас хорошие!
5 жыл бұрын
Muito bom parabéns pelo seu trabalho sucesso
@baconneggs24065 жыл бұрын
Router works good for the ears set at 1/8 in and a stop block set at your desired length
@howardmcadams38522 жыл бұрын
Thanks Sir
@kiaya0075 жыл бұрын
suggestion: do all the ears on the bottom pieces for the frame at one time. cut the ears while it is still a board then make your individual pieces.
@skinnyswheelz53302 жыл бұрын
Nice Glass Piece!
@tonykillingsworth92473 жыл бұрын
If you work off the center of the board you can use the small stack dado for both size cuts ....before you slice them lay them flat on your jointer and take off 3/16 off both sides then slice them.!!! This will save you alot of time and extra work
@gregmf94276 жыл бұрын
Nice I dig the pipe
@dansarmar17 жыл бұрын
For the shoulders of the end bars just use your jointer to take the material off.
@baldeagleApiaries2 жыл бұрын
I always was told not to put anything smaller than my elbow into my ears.
@NBryanBlack3 жыл бұрын
Greetings from East Texas! Just watching this, it looks as if you had done a few processes in a slightly different order, you could have saved yourself a LOT of work, although you would have missed out on making all those wonderful glue sticks! ;) Thanks very much for making this video, and thanks a bunch for the warning about kickback on the tablesaw. I just acquired one, and it's nice to know some of the dangers to watch out for!
@IceManTX69
3 жыл бұрын
Hey, fellow Texan! Yes, I've seen a lot of coulda/shoulda when I go back and watch this. Still using those glue sticks though..probably last me the rest of my life. Table saw kick back is the worst. I hate it. I'm a bandsaw guy when possible. Table saw threw a piece of wood one time (when I was new) and it bounced off my shop walls several times before coming to rest. I didn't like that. lol
@airwolf619705 жыл бұрын
Nice shop smith! I've never made a frame from scratch but a think alot of those little cuts could be done easier and faster if you would make them on the big board before you release all the parts from the board. Instead of 200 little cuts per cut you could Do 20. Have you made anymore frames? I'd love to hear and possibly see what you've learned. Like: what cuts are most efficient on the board? And what cut has to be made as a individual part? Great video!
@josevidales13787 жыл бұрын
nice bro nice that pipe to lol in the back
@airwolf619706 жыл бұрын
On the tenon jig. Would it be more stable and safe to clamp the wood to the jig? As you cut it.
@jkgkjgkijk4 жыл бұрын
My friend, Google Paul sellers chisel sharpening. Buy you a cheap set a chisels and do like he does to sharpen. You can save that last step by using a chisel instead of band saw. Those sticks are also good for foundationless frames as comb starters
@IceManTX69
4 жыл бұрын
Greyghost680 I love Paul sellers! I built my workbench according to his perfect example. This video is several years old and I have learned a lot of tips since then. Thanks for watching!
@blacktalonbased8 жыл бұрын
I made my own frames and boxes this last winter because I wanted the challenge. It was very rewarding!Then I made splits last week and had to buy more frames. haha...
@IceManTX69
8 жыл бұрын
Me too! But I bought the unassembled frames so I could still feel like I was woodworking. LOL
@blacktalonbased
8 жыл бұрын
+Plain 'Ol Beekeeping in Plano, TX I found some Amish made frames locally. unassembled for 73 cents.
@IceManTX69
8 жыл бұрын
+blacktalonbased Good price!
@cinchup11
7 жыл бұрын
Do you have a contact info on the Amish made frames?
@thegardenfarmer6 жыл бұрын
Nice bowl around 27mins, on back table lol
@IceManTX69
6 жыл бұрын
DOH!
@melloneemcdonald3767
5 жыл бұрын
@@IceManTX69 As long as its organic.
@FloryJohann7 жыл бұрын
Seems to be a lot of work and time involved, considering that you can buy them relatively cheap.
@ExtraFungus8 жыл бұрын
nice to see another beekeeper in the area. I'm in terrell.
@ce6827
8 жыл бұрын
Hello, I'm south of Kemp (Tolosa), in southern Kaufman County. My son works in Terrell and I use to. I've seen you on FB also. Think I'm going to get a Nuc this week. Very excited.
@ExtraFungus
8 жыл бұрын
+Celie Canada cool, we have "kaufman county beekeepers" and "north texas bee trader" on facebook, both excellent resources for your area.
@ce6827
8 жыл бұрын
Yes, thanks, I have joined both. Very helpful.
@ExtraFungus
8 жыл бұрын
yes I remember the last name now.
@ce6827
8 жыл бұрын
I see there is an association that meets 2nd Tues of month in Canton. Are you member there?
@jenntek.1017 жыл бұрын
Your ShopSmith ROCKS! - Is the table saw portion always that quiet when you cut? (Motor)... Man o' Man... I shoulda bought one when I had the chance. Very Very nice job on the frames. Seems like I would use the band saw more than the table saw for the bulk of the work... Seems like less waste. Thank you for putting this out here for all of us woodworking beekeepers.... :D
@IceManTX69
7 жыл бұрын
Jenn Tek I agree, the bandsaw is my favorite to use. Less scary on the finger losing side. No danger of kickback and much less waste.
@IceManTX69
7 жыл бұрын
Also, I forgot to comment on the sound. No, it isn't that quiet. It's noisy as all heck. I just lowered the volume to save the viewer's ears!
@benjaminlangford76977 жыл бұрын
Great video! I have a process improvement suggestion. If you use your table saw to cut all the bottom tapers on the entire block before you slice them, you will save alot of time and the table saw will remove all the wood. This process will eliminate the cutting and trimming of the tapers. That would save alot of wear on your scroll saw. I'm not trying to criticize just suggest. I'm a systems engineer, so I spend every day trying to remove a few seconds out of a process.
@benjaminlangford7697
7 жыл бұрын
Sorry, just realized that is what Hives2Honeyfarm is suggesting.
@erikdarm8 жыл бұрын
Good on you Josh. Just watching you made me tired.
@IceManTX69
8 жыл бұрын
Ha! Thanks. I won't be making them again any time soon. Lol
@kiaya0075 жыл бұрын
was just wondering why you are not using the clamp on your jig to hold the piece in place while you make the cut. is it broken or maybe it does not hold the piece properly. got to be a firmer grip than your hand bro.
@IceManTX69
5 жыл бұрын
I think it wasn''t holding it firm enough but it's been so long ago I honestly don't remember why I was doing that.
@McKeesBees5 ай бұрын
What you smoking out of that glass pipe? lol thanks for sharing great video.
@McKeesBees
5 ай бұрын
I see someone already talked about it after looking.
@IceManTX69
5 ай бұрын
@@McKeesBees 420 Glass pipes and power tools......what could go wrong! LOL
@aaronacj6 жыл бұрын
I feel you could make most the cuts on the wood while it's still a board then go through and make the 1/4 inch slices, saving you 300+ cuts...
@IceManTX69
6 жыл бұрын
Aaron Jones I agree! Since I made this video I've noticed several places I could have saved some time possibly.
@jackbquick123
5 жыл бұрын
@@IceManTX69 first video is awesome! If you ever thought about making another one with the things you have found out since this video it would be very appreciated. I am just starting out with bees and this is awesome thanks and nice shopsmith. What model is that one? Mine is a 510
@IceManTX69
5 жыл бұрын
@@jackbquick123 I need to check. I think it is a 510 as well. It's pretty old. My mom bought it new in 1985 and gave it to me around 2014 when I built my shop. It still works very well.
@khawk73655 жыл бұрын
Thanks for sharing mistakes and all.
@nealcox8204 Жыл бұрын
Question: Could you not cut the cut away parts from the bottom of the side bars while they are still in the 2x4 mode and then cut the side bars apart after to avoid hand cutting every little cut away part on each one?
@IceManTX69
Жыл бұрын
Most definitely and my mistake has been pointed out many times. 😉
@stevecorcoran29605 жыл бұрын
Should have made your dado cuts on the 10 inch boards.
@aliasglilou79144 жыл бұрын
New subscriber
@aaronacj2 жыл бұрын
Shouldn’t the angle stop be pushing the wood?
@ce68278 жыл бұрын
Where is best place to buy? Also, when first starting what type do you suggest. I ordered hive combo kit from Mann Lake that is coming with frames with Rite-cell. Not really sure what that is, but it comes with kit.Thank you
@IceManTX69
8 жыл бұрын
That should be a good starter kit! I buy from MannLake as well.
@airwolf61970
6 жыл бұрын
Usually if you buy 100, you will get a substantial discount.
@Storm-0911
4 жыл бұрын
This is an older post, but a great one but I bought equipment from little bee farm. He is almost local in Gordenville Tx. He seams to be the cheapest I found.
@rikhuramai958 Жыл бұрын
Why is the frame very lengthy? Instead of 19 inches, like can we make to 12 inches or something smaller? And wat difference will it make?
@IceManTX69
Жыл бұрын
These specifications are for a Langstroth hive and that is the dimensions. You do not want any extra open space in the box so the frames need to match the box size. I've seen all types of hives and you can make them smaller.
@PhillipHall017 жыл бұрын
why cant you cut the top and bottom 5/8 inch and when you make the top bar, just simply set the difference then? would save set up time? Since you are making the sides i feel confident that you are making the top bars also? Thanks
@IceManTX69
7 жыл бұрын
Yes, this would work. In hind sight I see a few areas where I could have saved a few strokes and more time.
@PhillipHall01
7 жыл бұрын
I like our channel, I have subscribed.. thanks for the video
@PhillipHall01
7 жыл бұрын
that was suppose to be i like your channel,, i subscribed
@WilliamMcNett
6 жыл бұрын
3/4" 😉
@abejasvillarrica15 жыл бұрын
Hey, I am Francisco from Chile , can you tell me where did you buy the Mountain range, I will be really gratefull , thanks for the video
@IceManTX69
5 жыл бұрын
Mountain Range?
@abejasvillarrica1
5 жыл бұрын
Yes, that one
@426superbee45 жыл бұрын
They use soft pine for frames
@bobwebber85214 жыл бұрын
So my question would be - What cost to purchase that number of frames ready to assemble as opposed to the cost of materials and time even if you had the machinery? Bet this kept you out of the house for a good while. BUT good video and well presented. Thanks.
@IceManTX69
4 жыл бұрын
Hey, I'll be honest, these things are (were, not sure now years later) so cheap from some place like Mann Lake. I did this to see if I could really and honestly I would never do it again as cheap as they are.
@Hives2honeyfarm7 жыл бұрын
you drew arrows to prevent the mistake you made, but when you cut them up, you lost your arrows.( I had to laugh), but like your video and how you show your mistakes. you rock. To make things go faster, why not use a dado blade and cut that 1/8" off, before you rip all the pieces. just run the face sideways on a table saw with a dado installed. it will take a few passes, but will be a lot faster than all that band saw work.
@Hives2honeyfarm
7 жыл бұрын
just to be clear, I'm talking about using the dado on the end bars. The underneath portion of the self spacers.
@IceManTX69
7 жыл бұрын
That would have saved me some time! Good Tip!
@aliasglilou79144 жыл бұрын
Your table is it a Bosch?
@IceManTX69
4 жыл бұрын
No, It is a ShopSmith Mark V
@cristidinu97525 жыл бұрын
Salut
@lizspencer6058 жыл бұрын
That's a LOT of work. That's why I buy mine. (That and I don't have a shop)
@IceManTX69
8 жыл бұрын
Shop or no shop, I'm buying from now on!😉
@lizspencer605
8 жыл бұрын
I don't blame ya!!!
@ExtraFungus
8 жыл бұрын
+Plain 'Ol Beekeeping in Plano, TX I'm playing with laser cutting frame parts, not sure how well the bees will like the burned edges though.
@IceManTX69
8 жыл бұрын
+Josh Bishop laser cutting is probably way less hassle!
@paulomarques20743 жыл бұрын
Bom dia meu amigo tbm? esse disco de Serra da pra colocar em qualquer serra de bancada?
@IceManTX69
3 жыл бұрын
No, I think it was made special for this machine. They do make them for other machines too.
@dennistmenace42077 жыл бұрын
do you sell any frames ?
@IceManTX69
7 жыл бұрын
Dennis T Menace No, I only made enough for me and I doubt I'll do it again. 😉
@dennistmenace4207
7 жыл бұрын
its a pain , i did it once , im going to buy them from now on ! great video though , i enjoyed it , thanks for the reply !
@ivansoroka45977 жыл бұрын
Hello from Ukraine I watch your video composing saw super where you can buy as a thank you called earlier
@arturomedina25905 жыл бұрын
muy buen video tu disco para hacer uniones tipo dedo aca en mexico no hay en venta en tu pais lo tendran a la venta y cual es el costo o puedes proporcionar informes de algun almacen donde lo vendan te agradeceria la informacion saludos desde morelia michoacan mexico
@IceManTX69
5 жыл бұрын
Busque Dado blade en Amazon o algo similar. El mío es muy viejo y me lo dieron mis padres.
@arturomedina2590
5 жыл бұрын
@@IceManTX69 gracias por tu informacion saludos
@jkgkjgkijk4 жыл бұрын
Man is smart: half pass
@beryal-honey6 ай бұрын
سلام این دستگاه سازنده کدام کشور است
@IceManTX69
6 ай бұрын
United States.
@DavidEricPrates7 жыл бұрын
Great video and good stuff! Maybe you can swing by my channel too sometime.
@Albertinhus Жыл бұрын
O pqdrao 'langstroth' não existe nos e.u.a. A medida menor é 13,7 e nao 15,875
@mmarkgraf2128 жыл бұрын
The part where you cut the side indents, why not stack like 3 or 4 at a time, you would just need a taller stop and backstop.
@IceManTX69
8 жыл бұрын
Good idea!
@andreighe3233
7 жыл бұрын
for the long sides (top & bottom): would it be possible to make some of the end adjustments while you still have the big boards?
@IceManTX69
7 жыл бұрын
+Andrei Ghe That might be possible. But I'm having a hard time visualizing how I Could do it.
@andreighe3233
7 жыл бұрын
to visualize how, just arrange the final pieces as if you would like to glue them to recreate the original board. And then see which common surface can be cut in one go, before splitting into pieces. I think the cuts shown at 29:32 could be made in one go, before splitting into pieces.
@IceManTX69
7 жыл бұрын
+Andrei Ghe that would save some time!
@superiorvideoandphotograph375 Жыл бұрын
ok so you made a few mistakes I wonder if the glass bowl on the bench had anything to do with this, LOL
@IceManTX69
Жыл бұрын
That was my first time making those (and my last) so there was some ignorance that might have been coupled with brain haze. 😆
@stevevorpe573511 ай бұрын
Traduire en Francais
@cherylhurley7401 Жыл бұрын
Please work on your audio can't hear you sorry
@IceManTX69
Жыл бұрын
It only lasts for the first minute. That’s why I put the warning on. The rest of the video is fine.
Пікірлер: 130
the best video for making frames. thank you
Great video, very informative; exactly what is needed to make my own frames. This is clear and easy for my old eyes to see what needs to be seen.
Thank you...........I've searched KZread for an hour looking for exactly what your video shows.......thank's.....
@IceManTX69
2 жыл бұрын
I'm glad it has helped you. There are many things in the video I wish I could have done better so I'm always glad to hear when it has helped someone. Interested to see how your blueberry mead turns out!
Amazing tool. Really nice work...
Nice. I used the jointer plain for the bee space on the side. Made it a bit higher too, so bees have more working space. Well presented very practical. Thanks
@IceManTX69
Жыл бұрын
Thank you for your contribution!
Like the pipe!
Tools to make boxes and frames. chop saw, jointer, tablesaw, dido stack and nails and glue.
great job and great instructions
good job and yes its fun to make your own equipment
Great video ! Thank you.
salut. very very good works man. thankyou.
Great video. Love your Shop Smith.
@IceManTX69
10 ай бұрын
Hey thanks! Too kind. My mom bought it in 1985 and she built many great things using it. She gave it to me a couple of years before she passed and I have enjoyed learning how to use it.
great video keep up the good work
hello and thanks for the video! I also made frames and yes, it takes forever... I have a tip for you for making sides : cut the lumber so you have two sides in length , the middle being the top bar. then cut in your jointer the extra wood(the glue sticks) , make the bottom groove, cut them in half, make the top groove and then cut them individually.
Wow, big difference after new parts on the band saw. Nice gear for the wood shop. Thanks for the video, I subscibed.
While I'm not a "Safety Sally" I'd like to mention that there probably should have been a feather board or two used on the 2 x 4" side piece dado work? Quick and easy to make and having owned and used my Shopsmith for many years I know that I would be using them - especially on awkward, tall, end grain work.
@IceManTX69
3 ай бұрын
Yes, you are correct! I have the plastic SS feather board and I should have definitely been using it. I had got the SS from my mom and only had it for a brief time when I made this video. Learned a lot of lessons in the beginning the hard way and luckily I still have all my fingers. I did some stupid and shady things.....
Станки у вас хорошие!
Muito bom parabéns pelo seu trabalho sucesso
Router works good for the ears set at 1/8 in and a stop block set at your desired length
Thanks Sir
suggestion: do all the ears on the bottom pieces for the frame at one time. cut the ears while it is still a board then make your individual pieces.
Nice Glass Piece!
If you work off the center of the board you can use the small stack dado for both size cuts ....before you slice them lay them flat on your jointer and take off 3/16 off both sides then slice them.!!! This will save you alot of time and extra work
Nice I dig the pipe
For the shoulders of the end bars just use your jointer to take the material off.
I always was told not to put anything smaller than my elbow into my ears.
Greetings from East Texas! Just watching this, it looks as if you had done a few processes in a slightly different order, you could have saved yourself a LOT of work, although you would have missed out on making all those wonderful glue sticks! ;) Thanks very much for making this video, and thanks a bunch for the warning about kickback on the tablesaw. I just acquired one, and it's nice to know some of the dangers to watch out for!
@IceManTX69
3 жыл бұрын
Hey, fellow Texan! Yes, I've seen a lot of coulda/shoulda when I go back and watch this. Still using those glue sticks though..probably last me the rest of my life. Table saw kick back is the worst. I hate it. I'm a bandsaw guy when possible. Table saw threw a piece of wood one time (when I was new) and it bounced off my shop walls several times before coming to rest. I didn't like that. lol
Nice shop smith! I've never made a frame from scratch but a think alot of those little cuts could be done easier and faster if you would make them on the big board before you release all the parts from the board. Instead of 200 little cuts per cut you could Do 20. Have you made anymore frames? I'd love to hear and possibly see what you've learned. Like: what cuts are most efficient on the board? And what cut has to be made as a individual part? Great video!
nice bro nice that pipe to lol in the back
On the tenon jig. Would it be more stable and safe to clamp the wood to the jig? As you cut it.
My friend, Google Paul sellers chisel sharpening. Buy you a cheap set a chisels and do like he does to sharpen. You can save that last step by using a chisel instead of band saw. Those sticks are also good for foundationless frames as comb starters
@IceManTX69
4 жыл бұрын
Greyghost680 I love Paul sellers! I built my workbench according to his perfect example. This video is several years old and I have learned a lot of tips since then. Thanks for watching!
I made my own frames and boxes this last winter because I wanted the challenge. It was very rewarding!Then I made splits last week and had to buy more frames. haha...
@IceManTX69
8 жыл бұрын
Me too! But I bought the unassembled frames so I could still feel like I was woodworking. LOL
@blacktalonbased
8 жыл бұрын
+Plain 'Ol Beekeeping in Plano, TX I found some Amish made frames locally. unassembled for 73 cents.
@IceManTX69
8 жыл бұрын
+blacktalonbased Good price!
@cinchup11
7 жыл бұрын
Do you have a contact info on the Amish made frames?
Nice bowl around 27mins, on back table lol
@IceManTX69
6 жыл бұрын
DOH!
@melloneemcdonald3767
5 жыл бұрын
@@IceManTX69 As long as its organic.
Seems to be a lot of work and time involved, considering that you can buy them relatively cheap.
nice to see another beekeeper in the area. I'm in terrell.
@ce6827
8 жыл бұрын
Hello, I'm south of Kemp (Tolosa), in southern Kaufman County. My son works in Terrell and I use to. I've seen you on FB also. Think I'm going to get a Nuc this week. Very excited.
@ExtraFungus
8 жыл бұрын
+Celie Canada cool, we have "kaufman county beekeepers" and "north texas bee trader" on facebook, both excellent resources for your area.
@ce6827
8 жыл бұрын
Yes, thanks, I have joined both. Very helpful.
@ExtraFungus
8 жыл бұрын
yes I remember the last name now.
@ce6827
8 жыл бұрын
I see there is an association that meets 2nd Tues of month in Canton. Are you member there?
Your ShopSmith ROCKS! - Is the table saw portion always that quiet when you cut? (Motor)... Man o' Man... I shoulda bought one when I had the chance. Very Very nice job on the frames. Seems like I would use the band saw more than the table saw for the bulk of the work... Seems like less waste. Thank you for putting this out here for all of us woodworking beekeepers.... :D
@IceManTX69
7 жыл бұрын
Jenn Tek I agree, the bandsaw is my favorite to use. Less scary on the finger losing side. No danger of kickback and much less waste.
@IceManTX69
7 жыл бұрын
Also, I forgot to comment on the sound. No, it isn't that quiet. It's noisy as all heck. I just lowered the volume to save the viewer's ears!
Great video! I have a process improvement suggestion. If you use your table saw to cut all the bottom tapers on the entire block before you slice them, you will save alot of time and the table saw will remove all the wood. This process will eliminate the cutting and trimming of the tapers. That would save alot of wear on your scroll saw. I'm not trying to criticize just suggest. I'm a systems engineer, so I spend every day trying to remove a few seconds out of a process.
@benjaminlangford7697
7 жыл бұрын
Sorry, just realized that is what Hives2Honeyfarm is suggesting.
Good on you Josh. Just watching you made me tired.
@IceManTX69
8 жыл бұрын
Ha! Thanks. I won't be making them again any time soon. Lol
was just wondering why you are not using the clamp on your jig to hold the piece in place while you make the cut. is it broken or maybe it does not hold the piece properly. got to be a firmer grip than your hand bro.
@IceManTX69
5 жыл бұрын
I think it wasn''t holding it firm enough but it's been so long ago I honestly don't remember why I was doing that.
What you smoking out of that glass pipe? lol thanks for sharing great video.
@McKeesBees
5 ай бұрын
I see someone already talked about it after looking.
@IceManTX69
5 ай бұрын
@@McKeesBees 420 Glass pipes and power tools......what could go wrong! LOL
I feel you could make most the cuts on the wood while it's still a board then go through and make the 1/4 inch slices, saving you 300+ cuts...
@IceManTX69
6 жыл бұрын
Aaron Jones I agree! Since I made this video I've noticed several places I could have saved some time possibly.
@jackbquick123
5 жыл бұрын
@@IceManTX69 first video is awesome! If you ever thought about making another one with the things you have found out since this video it would be very appreciated. I am just starting out with bees and this is awesome thanks and nice shopsmith. What model is that one? Mine is a 510
@IceManTX69
5 жыл бұрын
@@jackbquick123 I need to check. I think it is a 510 as well. It's pretty old. My mom bought it new in 1985 and gave it to me around 2014 when I built my shop. It still works very well.
Thanks for sharing mistakes and all.
Question: Could you not cut the cut away parts from the bottom of the side bars while they are still in the 2x4 mode and then cut the side bars apart after to avoid hand cutting every little cut away part on each one?
@IceManTX69
Жыл бұрын
Most definitely and my mistake has been pointed out many times. 😉
Should have made your dado cuts on the 10 inch boards.
New subscriber
Shouldn’t the angle stop be pushing the wood?
Where is best place to buy? Also, when first starting what type do you suggest. I ordered hive combo kit from Mann Lake that is coming with frames with Rite-cell. Not really sure what that is, but it comes with kit.Thank you
@IceManTX69
8 жыл бұрын
That should be a good starter kit! I buy from MannLake as well.
@airwolf61970
6 жыл бұрын
Usually if you buy 100, you will get a substantial discount.
@Storm-0911
4 жыл бұрын
This is an older post, but a great one but I bought equipment from little bee farm. He is almost local in Gordenville Tx. He seams to be the cheapest I found.
Why is the frame very lengthy? Instead of 19 inches, like can we make to 12 inches or something smaller? And wat difference will it make?
@IceManTX69
Жыл бұрын
These specifications are for a Langstroth hive and that is the dimensions. You do not want any extra open space in the box so the frames need to match the box size. I've seen all types of hives and you can make them smaller.
why cant you cut the top and bottom 5/8 inch and when you make the top bar, just simply set the difference then? would save set up time? Since you are making the sides i feel confident that you are making the top bars also? Thanks
@IceManTX69
7 жыл бұрын
Yes, this would work. In hind sight I see a few areas where I could have saved a few strokes and more time.
@PhillipHall01
7 жыл бұрын
I like our channel, I have subscribed.. thanks for the video
@PhillipHall01
7 жыл бұрын
that was suppose to be i like your channel,, i subscribed
@WilliamMcNett
6 жыл бұрын
3/4" 😉
Hey, I am Francisco from Chile , can you tell me where did you buy the Mountain range, I will be really gratefull , thanks for the video
@IceManTX69
5 жыл бұрын
Mountain Range?
@abejasvillarrica1
5 жыл бұрын
Yes, that one
They use soft pine for frames
So my question would be - What cost to purchase that number of frames ready to assemble as opposed to the cost of materials and time even if you had the machinery? Bet this kept you out of the house for a good while. BUT good video and well presented. Thanks.
@IceManTX69
4 жыл бұрын
Hey, I'll be honest, these things are (were, not sure now years later) so cheap from some place like Mann Lake. I did this to see if I could really and honestly I would never do it again as cheap as they are.
you drew arrows to prevent the mistake you made, but when you cut them up, you lost your arrows.( I had to laugh), but like your video and how you show your mistakes. you rock. To make things go faster, why not use a dado blade and cut that 1/8" off, before you rip all the pieces. just run the face sideways on a table saw with a dado installed. it will take a few passes, but will be a lot faster than all that band saw work.
@Hives2honeyfarm
7 жыл бұрын
just to be clear, I'm talking about using the dado on the end bars. The underneath portion of the self spacers.
@IceManTX69
7 жыл бұрын
That would have saved me some time! Good Tip!
Your table is it a Bosch?
@IceManTX69
4 жыл бұрын
No, It is a ShopSmith Mark V
Salut
That's a LOT of work. That's why I buy mine. (That and I don't have a shop)
@IceManTX69
8 жыл бұрын
Shop or no shop, I'm buying from now on!😉
@lizspencer605
8 жыл бұрын
I don't blame ya!!!
@ExtraFungus
8 жыл бұрын
+Plain 'Ol Beekeeping in Plano, TX I'm playing with laser cutting frame parts, not sure how well the bees will like the burned edges though.
@IceManTX69
8 жыл бұрын
+Josh Bishop laser cutting is probably way less hassle!
Bom dia meu amigo tbm? esse disco de Serra da pra colocar em qualquer serra de bancada?
@IceManTX69
3 жыл бұрын
No, I think it was made special for this machine. They do make them for other machines too.
do you sell any frames ?
@IceManTX69
7 жыл бұрын
Dennis T Menace No, I only made enough for me and I doubt I'll do it again. 😉
@dennistmenace4207
7 жыл бұрын
its a pain , i did it once , im going to buy them from now on ! great video though , i enjoyed it , thanks for the reply !
Hello from Ukraine I watch your video composing saw super where you can buy as a thank you called earlier
muy buen video tu disco para hacer uniones tipo dedo aca en mexico no hay en venta en tu pais lo tendran a la venta y cual es el costo o puedes proporcionar informes de algun almacen donde lo vendan te agradeceria la informacion saludos desde morelia michoacan mexico
@IceManTX69
5 жыл бұрын
Busque Dado blade en Amazon o algo similar. El mío es muy viejo y me lo dieron mis padres.
@arturomedina2590
5 жыл бұрын
@@IceManTX69 gracias por tu informacion saludos
Man is smart: half pass
سلام این دستگاه سازنده کدام کشور است
@IceManTX69
6 ай бұрын
United States.
Great video and good stuff! Maybe you can swing by my channel too sometime.
O pqdrao 'langstroth' não existe nos e.u.a. A medida menor é 13,7 e nao 15,875
The part where you cut the side indents, why not stack like 3 or 4 at a time, you would just need a taller stop and backstop.
@IceManTX69
8 жыл бұрын
Good idea!
@andreighe3233
7 жыл бұрын
for the long sides (top & bottom): would it be possible to make some of the end adjustments while you still have the big boards?
@IceManTX69
7 жыл бұрын
+Andrei Ghe That might be possible. But I'm having a hard time visualizing how I Could do it.
@andreighe3233
7 жыл бұрын
to visualize how, just arrange the final pieces as if you would like to glue them to recreate the original board. And then see which common surface can be cut in one go, before splitting into pieces. I think the cuts shown at 29:32 could be made in one go, before splitting into pieces.
@IceManTX69
7 жыл бұрын
+Andrei Ghe that would save some time!
ok so you made a few mistakes I wonder if the glass bowl on the bench had anything to do with this, LOL
@IceManTX69
Жыл бұрын
That was my first time making those (and my last) so there was some ignorance that might have been coupled with brain haze. 😆
Traduire en Francais
Please work on your audio can't hear you sorry
@IceManTX69
Жыл бұрын
It only lasts for the first minute. That’s why I put the warning on. The rest of the video is fine.