So, your clip was the first I found to be simple, straightforward, WELL LIT and understandable. Thank you for this quality video. This gave me the confidence to tackle the front suspension at 6 PM before going to work the next day. :)

@taridean

5 жыл бұрын

I was thinking the exact same thing. A lot of the IS200/IS300 coilover install videos on here are disappointing. Missed steps, bad lighting, going off topic and most of the time nausiating (badly framed) camera movements.

@mikejamieson419

2 жыл бұрын

Except he pretty much takes the whole car apart lol 😂

That’s such a clean looking is300

This is a great video very helpful thank you so much :)

Just as a heads up for anybody doing the install, there is no need to disconnect the swaybar. It may be helpful when trying to get the bottom of the strut to line back up on the installation, but I feel it was just as easy doing it without it being disconnected. Mine were rusted out and couldn't get an alan key in it anyway

@trozz7660

5 жыл бұрын

Mine was keeping the bottom 17mm pin on the strut from going in until I disengaged it. I didn't want to disconnect it either but when I did it was way easier.

Damn I didn't not do anything like that when installing my coils. Granted this is the correct way to install. However I installed them without taking any arms off or sway bar Just rattled alot of stuff and stuck a break bar against the arm to help lower it...

I have a question for anyone that runs coils on a daily... how long do they usually last for you guys? I’m in Chicagoland area and the winters are brutal with road salt. Is it possible to drive on these 20k miles/year, all year round, with no garage, and not need rebuild or replacement?

Do these coilovers for the is300 come with no camber adjustments??

Hello ! Did you needed to correct geometry ?

for anyone that ordered these coils did they not come with an adjustable camber plater for the fronts?

Do you have an outlet in the Caribbean

i’ve been having trouble installing mine bc one of the bolts that connects the bottom of the coil to the arm doesn’t want to come off, i’ve tried putting wd40 on it, several good different impacts & it has broke 3 of my tools as well, any tips? that’s the only thing that’s preventing me from installing them

Need these coil overs for my altezza

@dangelovalentin8958

3 жыл бұрын

pro trick: watch movies on Flixzone. I've been using them for watching loads of movies recently.

@dakarimaxton3417

3 жыл бұрын

@Dangelo Valentin yup, I have been watching on Flixzone for since november myself =)

I just installed coilovers on my is300 and now I have a little bit of camber why? And how do I fix it?

@KevinEdgar

Жыл бұрын

geometry

What is the spring rate for this setup? front and rear? or what do you recommend?

@BCRacingNorthAmerica

4 жыл бұрын

12kg front & 10kg rear!

take my like and Sub, thank you, you are a good man.

Do the struts come adjusted already for the height

@BCRacingNorthAmerica

4 жыл бұрын

They come preset with a "out of the box" ride height. You can then further adjust the ride height before or after installation.

Will the process be the same for 02 is300 wagon?

@miguelhxrnandez

9 ай бұрын

same process

What wheel setup do you have for the is300?

@anthonybaltera6556

6 жыл бұрын

those are konig hypergrams. interested as well on wheel offset, width, and tire size the offset, width, and sidewall meat is effin perfect. thanks for the awesome video Kevin! Go BC!!

@lennex04

4 жыл бұрын

Yeah super curious on the tire and off set. And what color are those. Looks silver but then again looks a tad bit bronze. Goes very well

whats the spring rate you went with.

@BCRacingNorthAmerica

4 жыл бұрын

12kg front & 10kg rear!

@sammylegaspi2214

3 жыл бұрын

@@BCRacingNorthAmerica does that rate happen to have any rubbing?? idk if that sounds dumb but I’m actually just curious lol

I just installed some teins on my is300. Had the fronts on with no problem and they ride great. I installed my rears they are really bouncy, any tips?

@BCRacingNorthAmerica

4 жыл бұрын

I would speak to a representative of the companies product you are referring you.

Dude needs a torque wrench!