Battery restoration| rebuild NI-CD to li-ion for makita impact wrench old version

In this video I will restore and replace nicd to Li-ion battery with BMS for old model Makita impact wrench
I hope you find this video useful and enjoy!
I’m happy to receive your feedback.
Thank you very much for your likes and your comments
#repair_and_restoration
#nicd_to_liion
#battery_replacement
#repair
#restoration
#rebuild_battery

Пікірлер: 14

  • @m.nooria.8957
    @m.nooria.895710 ай бұрын

    Goed gedaan 👏👏👏

  • @robinmidgett3347
    @robinmidgett3347 Жыл бұрын

    Please list the sources for the LiOn batteries and the BMS. Are these 18650 batteries you chose?

  • @arenasinda_kor_savasci
    @arenasinda_kor_savasciАй бұрын

    Merhabalar bms devre şemasını paylaşırmisiniz

  • @repairandrestoration4238
    @repairandrestoration42382 жыл бұрын

    Thank you very much for your like, and subscription

  • @jonhamilton8247
    @jonhamilton82478 ай бұрын

    Nothing like a good :calibrated impact adjustment :

  • @manofallseasons8752
    @manofallseasons87525 ай бұрын

    Nice Job!!!

  • @paulmichaelfreedman8334

    @paulmichaelfreedman8334

    3 ай бұрын

    The only problem I have with this video is the use of an impact wrench to tighten vehicle bolts which always have specific torque specs..😵‍💫 You're asking for a mid-journey freak accident.

  • @metroh6094
    @metroh6094 Жыл бұрын

    Very good 👍😊هاذا لي اريده

  • @alexandres8846
    @alexandres88462 жыл бұрын

    To balance nimh battery packs, a circuit with two 1n4007 diodes in series plus a resistance of 1 to 10 ohms is used.The voltage drop in each diode is 0.7 volt x 2 is 1.4 volts.The resistance limits the intensity of the balancing current. Being soldered to all Ni cells this increases the life and performance of the battery pack.

  • @repairandrestoration4238

    @repairandrestoration4238

    2 жыл бұрын

    Thank for your infomation!❤️❤️❤️❤️

  • @khosrowbahari4064

    @khosrowbahari4064

    Жыл бұрын

    Hi sir Do you mean lituum batteri or nickel cadmium batteri? because in this video the guye rebuild nickel cadmium batteri to litium batteri.

  • @atdforgebc4605
    @atdforgebc46052 жыл бұрын

    May i ask why did you choose 4cell instead of 3 cells?. Is it ok to far exceed the voltage? Do these motors from power tools can handle higher voltages., if so by how much? Thank you

  • @alanerickson3075

    @alanerickson3075

    8 ай бұрын

    I am currently running a whole lot of older Makita and Hitachi 14.4 volt power tools on Milwaukee M18 batteries. First I made some adaptors to fit the M18's out of 4mm acrylic then I epoxied them to the top halves of the dead 14.4 NIMH battery cases and they slid right in. Other than having to put a screw in the old battery cases to hold them into the tools they work slick as owl shit. Also I've been using them set up like this for 7 or 8 years now with no problems whatsoever. I chose to use the M18's because I also have a lot of Milwaukee tools and you cant over discharge them as soon as they get below 18 volts they shut themselves off.

  • @normandothegreat
    @normandothegreat Жыл бұрын

    I have the 14.4 Makita set still like new, but the batteries are garbage. I wish you sold the upgraded kits.

Келесі