Basic Pumper Operations

Single Attack Line Deployment

Пікірлер: 19

  • @pipesmoker4238
    @pipesmoker42387 жыл бұрын

    Brings back memories....it's been 40 years since I operated a pump, can't believe it has been that long.

  • @clifduy4259

    @clifduy4259

    7 жыл бұрын

    Like riding a bike. Go down to visit your local station house. They'll probably invite you to dinner. June 29 2017 is my last shift after 34 years paid and two volunteer. Where did you operate fire pumps 40 years ago?

  • @pipesmoker4238

    @pipesmoker4238

    7 жыл бұрын

    Charlton, NY. At the time it was a small farming area with housing developments popping up. Half of the district had hydrants. We had a 1964 Mack thermodyne engine tanker holding 1600 gallons of water and a 1958 Mack engine holding 800 gallons. Both 750 pumps. We had a 1944 Chevrolet on a Buffalo frame. That held 500 gallons and had a 500 pump. We used that a lot for brush fires. Wasn't fwd but could go any ware. Our rescue truck was a 1958 Chevrolet on a 3/4 ton frame. Custom body that held medical supplies and other misc equipment related to our needs. They have replaced all vehicles with newer equipment.

  • @plingket

    @plingket

    6 жыл бұрын

    Damn. That's a long time

  • @engineerk34k7
    @engineerk34k77 жыл бұрын

    Hydrants what are those? Onboard tanks and porta-tanks and a lake.

  • @aportman58
    @aportman584 жыл бұрын

    I couldn't tell if that was a crosslay control valve but it appeared there was no needle on the gauge? It may have been a color that was difficult to visually see.

  • @danny88dh
    @danny88dh7 ай бұрын

    Well done guys

  • @chuckg2016
    @chuckg20163 жыл бұрын

    Potentially a really informative video except volume is too low.

  • @drewdoestrucks

    @drewdoestrucks

    2 жыл бұрын

    Agree. Even with volume maxed I can’t hear anything.

  • @detroitfirefighter
    @detroitfirefighter7 жыл бұрын

    When you hook in from your hydrant, and flowing water from it, do you shut down your Tank to Pump, or leave it open?

  • @harlitherainingwolf7289

    @harlitherainingwolf7289

    7 жыл бұрын

    You close it after you're hooked into hydrant water.

  • @cody5090

    @cody5090

    7 жыл бұрын

    I have seen it done either way, depends on the operator. One way i look at it is if for some reason you lose your hydrant your backup is ready to go right away no delay and safer for your men or women inside the structure.

  • @cody5090

    @cody5090

    7 жыл бұрын

    You should be watching your supply enough that if you would lose it you should know right away. And in turn figure out why you lost it and if needed get your personal out of the structure, especially if you're going to have to shut down quickly depending how hard you're pumping. It all depends on the truck. I know with the aerial that i run i can go through that 500 gallons on board in about 30 seconds if we have a major fire. But on say the rural truck engine we have i know i have about 2 minutes of on board water if pumping hard. And our engine is also different, Depends on your equipment a lot as well and every call is different.

  • @firetrainingsolutionsllc1164

    @firetrainingsolutionsllc1164

    6 жыл бұрын

    Mister X totally agree with you. It is common practice to shut your tank to pump valve as soon as you are on a pressurized supply, especially when you have a interior attack crew.

  • @rtazz17

    @rtazz17

    6 жыл бұрын

    Shut it. No matter what happens you have 500 gl to get your crew out of structure.

  • @Citrusfruits50
    @Citrusfruits506 жыл бұрын

    Nice biceps 💪👅

  • @sgt.guardsman2221
    @sgt.guardsman22215 жыл бұрын

    The volume on this video is sooo low I can't even understand what they are saying.

  • @michaelmackinnon2378
    @michaelmackinnon2378 Жыл бұрын

    They way you got out wasnt safe man could fall..its weird how to drive some/most fire trucks you dont need a c d l lol