Axial SCX10 II - STRC Aluminum Upgrades Installation & Overview
Автокөліктер мен көлік құралдары
Its time to start doing some changes to the Axial SCX10 II. Too start it off, I ordered up a bunch of awesome aluminum upgrades from STRC. One of the largest Aluminum upgrades manufactures for RC cars and Trucks.
In this video i break down how to install each and every part that I am upgrading on this crawler. As well as, provide a little bit of an overview for everyone. Especially for the new guys that might not have an idea on how to replace some of these components.
Overall I am very impressed with the install of these upgrades. It was very easy to install each of them and should provide a huge increase in the durability of this RC crawler.
Hopefully you found this video useful in installing some awesome aluminum upgrades into your own SCX10 II or even other RC Trucks.
I have listed below each and every part that i installed on my own SCX10 II. Feel free to check out the links for even more great upgrades from STRC!
STRC Home - www.teamstrc.com/index.php?rou...
All Axial SCX10 II Aluminum Upgrades List - www.teamstrc.com/index.php?rou...
ALL PART LINKS BELOW, ARE FOR GUN METAL ALUM. PARTS
Thanks for watching and don’t forget to subscribe and hit that notification bell!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~PRODUCTS USED IN TODAYS VIDEO~
-----------------------------------------------
Alum. Front HD shock Towers with Panhard Bar Setup -
www.teamstrc.com/index.php?rou...
Alum. Rear HD Shock Towers -
www.teamstrc.com/index.php?rou...
Alum. Front Steering Knuckles - www.teamstrc.com/index.php?rou...
Alum. Front C Hubs -
www.teamstrc.com/index.php?rou...
Alum. Rear Axle Lockouts - www.teamstrc.com/index.php?rou...
Alum. Diff Covers - www.teamstrc.com/index.php?rou...
Alum. Lower Shock/Link Mount Kit -
www.teamstrc.com/index.php?rou...
Alum. Servo Mount Brackets -
www.teamstrc.com/index.php?rou...
Alum. Front Bumper Mount - www.teamstrc.com/index.php?rou...
Alum. Rear Bumper Mount - www.teamstrc.com/index.php?rou...
Alum. Rear HD Crossbrace Mount - www.teamstrc.com/index.php?rou...
Axial SCX10 II Kit - amzn.to/2wj4RlQ
Axial SCX10 II RTR - amzn.to/2iD7r2V
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~AFFILIATES & COUPON CODES ~
------------------------------------------
VenomRC.com (Team Driver)
www.venompower.com
AsiaTees.com
bit.ly/21fgIKh
ProLineRacing.com
(10 % Coupon Code - RCOVERLOAD10)
www.prolineracing.com
RCJuice.com
(10 % Coupon Code - RCOVERLOAD10)
www.rcjuice.com
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~RECOMMENDED PRODUCTS~
---------------------------------------
RC Overload Shop - (Everything I currently use or have used before)
www.amazon.com/shop/rcoverload
Camera & Computer Gear - (Everything I currently use to film and edit with)
Camera Gear - amzn.to/2JdxfPB
Computer Equip - amzn.to/2E3LIcB
T-Shirts & Accessories
teespring.com/stores/rc-overload
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~ RC OVERLOAD SOCIAL MEDIA~
---------------------------------------------------------
WEBSITE - www.rcoverload.com
FACEBOOK - / rcoverloadmatt
INSTAGRAM - / _rcoverload_
TWITTER - / @rcoverload
162 MEDIA - www.162mediaproductions.com/
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~DISCLAIMER - RC Overload & 162 Media Productions~
*** The product(s) shown in this video may have been sent to me for review or for promotional means. Many of the links in the description box are affiliate links and I may benefit from a small affiliate commission if you purchase something using the links above. RC Overload is not responsible for your "own" actions with your radio controlled vehicles that is or was performed by yourself or anyone else.
© RC Overload & 162 Media Productions, All Rights Reserved.
Пікірлер: 97
Great job! You really explained everything very well and also did a good job of putting them all in!
@RCOverloadYT
7 жыл бұрын
+Sweet Rc thank you!
Hey Matt. Last Halloween I watched your live stream and it was awesome. You should do another one. Keep up the good work. I love your videos.
Awesome video on these upgrades, Thanks so much! I am currently ordering all of my upgrades before my build and this is what I was waiting for. Can't wait to see the next one on the wheels and tires I am still undecided on those.
@RCOverloadYT
7 жыл бұрын
+Julio Hernandez you won't be disappointed! Their awesome for sure. And most definitely on the tires. Ill have that out soon. Waiting on something to ship first before making the video.
@bodiejairo2140
2 жыл бұрын
i dont mean to be offtopic but does any of you know of a tool to get back into an Instagram account..? I was dumb lost my login password. I love any assistance you can offer me
@eduardozayn3735
2 жыл бұрын
@Bodie Jairo Instablaster ;)
@bodiejairo2140
2 жыл бұрын
@Eduardo Zayn i really appreciate your reply. I got to the site thru google and im waiting for the hacking stuff atm. I see it takes a while so I will reply here later with my results.
@bodiejairo2140
2 жыл бұрын
@Eduardo Zayn it did the trick and I finally got access to my account again. I'm so happy! Thanks so much you saved my account !
Strc all day . Love their stuff
@RCOverloadYT
7 жыл бұрын
+JPRC absolutly!
love your vids! any benefits to doing all the small alloy upgrades over getting a full alloy Axel? eg vanquish?
Beautiful upgrades! Hoping to see a new body because thats the only thing about this new rig I don't care for.Great video, thx for sharing !
@RCOverloadYT
7 жыл бұрын
+jo jo i agree. I love the look of it now. And yes i garenty more bodies will come soon! Lol
get brass lower links and shock cups. huge difference in how it crawls. and a brass steering link if your servo can handle that weight
Was also wondering what type of battery do you reccomend for the axial?
Nice strc upgrades looks freaking sick!!!!
@RCOverloadYT
7 жыл бұрын
+Lil Conan thank you! I agree, it definitely adds so much more to the truck.
@souledoutrc8174
6 жыл бұрын
RC Overload hey Matt how were the strc c hubs and knuckles holding up?
quick question .. would aftermarket aluminum axles for the scx10 fit on the scx10 2?
Swwweeeeet !! Love it, Great Video. My is all VP, I love this Rig. :-)
@RCOverloadYT
7 жыл бұрын
+andrew richey vp is great as well. Just a bit out of my price range at times lol. But yes the SCX10 II is an amazing rig!
Nice set of appearance AND strength upgrades, Matt!!! I've used STRC Parts before, always with good results!! It's unfortunate that some Asshat had to comment below, in a rude and condescending manner. Just uncalled for!!
Thanks for sharing this "how to...", is useful!!!
cant wait to see the running vid
@RCOverloadYT
7 жыл бұрын
+adam juneau very soon! ;)
Just wondering if this happened to anyone else. Mine STRC kit was installed and the front bar that connects the 2 wheels together seems to be to short cause both wheels are pointing in towards each other by about a 1/4 inch. Is there a special piece that I didn't get?
good thorough instructions really appreciate it!!! M
Awesome video. Thank you!
@RCOverloadYT
7 жыл бұрын
No problem! glad you enjoyed it!
Sweet setup!
@RCOverloadYT
6 жыл бұрын
Thanks!
any chance of you doing a four-wheel steering mod in the SCX 10 2 pretty please lol
I notice the screw for the panhard is longer now for the front shock tower is that ok?
nice ! what is stock c hub angle set to 10 degrees ?
Good video. I wish you would have had before and after pics. Still very helpful. Thanks 👍
Great job!
Looking good! 😊 Winter is here and time too upgrade my scale scx10.2, I do prefer ssd parts my self! 👍🏻
@RCOverloadYT
7 жыл бұрын
Thanks man! and yes SSD stuff is great!
can I run a venom 8.4 v 5000 mah 7-cell nimh battery in my scx10 2
Hello Matt, I can open the strc links, but can't find nothing on the site with it. can u check it please
What bit driver are you using?
hey matt will the scx10 2 axles fit the original scx10?
simply beautiful bro
@RCOverloadYT
7 жыл бұрын
I agree! it definitly makes the SCX10 II look that much better!
Definitely useful 👍
Little curious how much more it weights
Hello, what tools do you have ?
Do you have a video of you installing the links on it
Awesome video. can anyone of them be done to an Everest 10?
@funshootin1
7 жыл бұрын
Mario Berto hey Matt, I got my son an everest 10. we've been doing mods since day one. . crawling mostly, low cg ride height by making brackets, several motor and gearing changes for experimentation, 3s lipo.. the stock esc had a chernobly meltdown and we swapped that out.. I have been through the axles and I have to say they are fine with stock drive train but if you put more power to them the steering arms attached to the axle ends rip off under loading, we've snapped front shafts ,broke the knuckles ..stripped the plastic "locker" diff carrier. fortunately for us , this axle design is a common part used in several brands worldwide. . when searching ebay for parts use ,exceed maxstone, scx10, scx0001 , hsp pangolin and there's probably a few I'm forgetting. . anyways, you'll see in pics and parts descriptions that in most cases the parts are identical in every way...just be sure that you are looking for the axial scx10 axle parts that are for the original, older type of scx10 axle, not the "2" second generation. . you'll see in pics the difference between the ends of the axle tube where the steering arms or lockouts attach.. the splined end types are the newer style axles and most likely it won't directly fit on our everest 10s.. look for the older type axle with the screw retainers out at the ends of the tubes and the 4 screw diff housings with the same suspension link tabs.. those arethe ones you want to search for when looking for parts . . as far as the upgrades I am going to try the aluminum steering stuff. . Redcat wants like 24 bucks for knuckles and same for the mounting bracket. . 11 bucks on ebay, I guarantee it is manufactured by the same contract machine shop in Guangdong China . this will help the steering component strength but now the loads get transferred to the next plastic part which is the axles tube ends where steering inner knuckles mount, the 2 halfs are thin plastic with a bearing .. that's going to shear off so we're doing to do the "beef tubes " ..Essentially a liner for the axle tubes that supports the body from diff bearings to outboard bearings and the axle shaft runs through them.. they have tapped holes for the knuckle mounts to tie it all together. . if you're looking at upgrades I wouldn't go too crazy, I will be doing the ebay steering components , the tubes, hardened cv type axle shafts, and aluminum differentials but nothing else. . the cost /benefit ratio is too low to dump more than 40 to 50 bucks at an axle that you can get complete stock units for 35 bucks. . and aluminum and steel (cast im sure ) aftermarket complete axles that would require a tiny bit of modification to fit tge everest starting at 60 bucks. . I'm new to the crawler rc game, but I have had my share of rc stuff and the kids got redcat blackouts first, then arrma buggys, and we inherited a handful of chassis and partially complete parts cars which have been an awesome source for stupid screws , links, shocks ect. man if you are ever offered a big box of old rc "junk" do not say no to that. . that box has been a lifesaver countless times. also check out the everest 10 owners group on Facebook if you're on there.. there's folks who have a lot of knowledge about the everest so it's a good resource. . it's kinda like the redheaded stepchild of rc crawlers. . not a comp rig , not a scaler. . it's inexpensive and a great introduction to the crawling range of rc trucks , it's a decent enough machine and is a good value, for 140 bucks or so Ready to run there's nothing else with a traditonal center motor /trans and driveshafts to the axle (realistic layout ) that performs any better and has parts commonality with so many other things that the options are endless as to what you can get it to be. . more serious crawling or more scale looking either way is totally doable with a little ingenuity and not too much money.
links to parts say not found. looking for a guide like this for parts if anyone has one with links
What shocks are you using for this SCX?
love all the strc parts I installed..... except the c-hubs way to much play. tightened them as much as I could but they are still loose. any suggestions on how to get them to fit right?
@simonambo3681
7 жыл бұрын
Alice Copper get some shims in
@wildsau1965
7 жыл бұрын
Simon Lam shims won't do it, Teflon tape will probably be the only answer
@nealedmondson3191
6 жыл бұрын
Use thicker washers
these axle mods dont apply to SCX10 .2 with ar44, mine are all one piece. no longer can you replace the lower link mount ect
👍
Hey bro I was wondering if you or someone could save me some reaserching headache and give me some measurements! I'm still trying to transition from having a 4 link to a 3 link with Panhard bar setup. I went for a test run with scx10.2 rails and KYX 10.3 portals and even though I was steering all the way to the right it was actually driving angled to the left. (driving diagonally instead of straight) I put on the same links I had before. Is my upper link too long? Someone help me out!
A question, the supports the panhard bar rubs with the horn of the servo?
@RCOverloadYT
7 жыл бұрын
+Miguel Olmo nope no rubbing whats so ever.
@m.o.hdesigns9203
7 жыл бұрын
Could you tell me what type of servo and horn you use? If 25T you recommend me horn ?. Is that I have tried several and all of them touch me with the panhard bar.
Just got the scx 10 ii and I want the aluminum hopups any links ?
@RCOverloadYT
6 жыл бұрын
Gonna be re doing all the link in the video today. Sorry about that. Seems like STRC changed thier URL paths on all thier products.
Nice!
Hello nice really nice. Do you still have it?
I have a favor can you upgrade remo hobby 1073 rc. I dont know the patrs
what version of car you have? I just got mine and my rear axle housing looks nothing like yours, it's all plastice and has no pieces to come off for putting up grades on.
@RCOverloadYT
6 жыл бұрын
+Craig Chenault you most likely have the new axial Honcho version. That truck they cut back on a lot of stuff with it for some reason.
@craig8159
6 жыл бұрын
Yea must have what a bummer. oh well got new alum housings for front and back on way in mail.
hey matt, I can open the links, but the strc site says 'product not found'
@RCOverloadYT
7 жыл бұрын
+Bart Verelst hmm ill take a look into that. Thanks for the heads up.
honestly other than the added weight which could be accomplished by much cheaper means. This upgrade was just cosmetic. All the OEM parts are more than enough from an engineering stand point. Its a rock crawler its not made for racing and jumping. sure aluminum is harder than plastic BUT! the flexibility of plastic absorbs shock and can bend without breaking.
someone pls help/show me how to replace a servo horn of a scx10 ii
@MrFu75
5 жыл бұрын
Hello shVAK, have you managed to replace the scx10ii servo horn yet?
You should send me the factory wheels/tyres! Hahahahahahaha but seriously, nice rig, great vid.
@RCOverloadYT
7 жыл бұрын
Haha ive already got plans for those!
@AngryTurds
7 жыл бұрын
d'oh. as you do. There's no such thing as having "too many options" when it comes to tyre selection.
What type/kind of grease do you use?
@RCOverloadYT
7 жыл бұрын
+David Hoover i use cow rc udder butter currently.
@Deadfool31
7 жыл бұрын
RC Overload Where could I get some of that? Also what else would I be able to use if that is not available?
good one. Liked and subbed 👍
Super Video ; und Gruß aus München Germany - von Volker .
@RCOverloadYT
7 жыл бұрын
+Volker Sakowski thank you
at 3:42 the spring wasn't seated on the shock... just a little thing I noticed... who else noticed that? don't lie to me
0:29
i'm not a fan of the way the driver's shock tower doesn't fully capture the rod end of the panhard bar.
@humblerc841
7 жыл бұрын
i am an strc fan though, i've got a bunch of their stuff on the slash 4x4 and the exo.
@humblerc841
7 жыл бұрын
how are you liking the shocks?
@RCOverloadYT
7 жыл бұрын
+humble rc the Panhard bar setup is basically the same thing as the knuckles. And the knuckles experience more stress then the Panhard bar dose. I'm sure it will be fine. The stock shocks aren't my favorite let's put it that way. Lol
@humblerc841
7 жыл бұрын
RC Overload yeah they looked a little leaky in the close ups. i built the ones that came with mine for the practice, but i ended up putting scalers on the truck.
That's $325 USD of gear. More than the RTR cost me. :-/
Very expensive car and comes with a lot of plastic.
What is this? Model-building for individuals who´ve got an IQ below 60? If anyone needs a video to show how to change these simple parts, maybe same person ought to get him- / herself a new hobby like knitting...