What would you put a reversing esc in? 🤔🤔🤔

@charliemarchiony7914

3 жыл бұрын

Conscendo Advanced to shorten the approach. Same for my Radian, which doesn't have spoilerons. F-4 to shorten the rollout or for air braking. My apprentice to back up on the water. Of course it would just be nice to back up my P-39 and Cherokee.

@SVGERichy

3 жыл бұрын

My f-18, f-16 and my havoc XE

@charliemarchiony7914

3 жыл бұрын

@@SVGERichy The F-16 has too many cheater holes, but the Havoc would be perfect. If I ever get one, I’m putting smart in it for the reversing and battery telemetry to maximize flight times

@stuartworrell9442

3 жыл бұрын

Great video, and we'll explained. Love the idea you can update esc without programmer..... Question: will you eventually be able to update your smart receiver too from tx? Or will always need the cable?

@Providence365

3 жыл бұрын

Can two 100a esc talk to one tx? (Rpm info per motor purposes)

Wow can’t wait to try it !!!!

This video made my programming a piece of cake , thank you

Great video Thanks for the tips✌⭐⭐⭐⭐⭐🎬🎥🗽🤠

If I have an older DX8. Can I set up the reverse for the timber or draco ?

Nice instructional video, thank you. Please add the first step to enter the Smart ESC Programming Screen. I found this part missing from your video and only reading one of your replies realized that when you said go to Telemetry, it was not the Menu item but a full thumb roller to the right before you can see the menu for SMART ESC. Once there my model set up prevented me from completing the steps because the stick movement no longer resulted in +100 / -100 registering to the programmer. So I set up a new model, fresh called "TEST" with no limits or trim setting and I was able to enter the menu and change the ESC successfully using the instructions in this video. Very cool. Initially I tried using the Stick Programming Method and it didn't work properly. I know this because I have used the same method to program 3 other manufacturers ESCs and theirs seem to read my inputs more precisely. Overall this is a nice way to quickly change ESC parameters on the fly, but you still need to set up a fresh model with no presets for trim or rates so that the stick registers -100 at one end and +100 at the other. HOPE THIS HELPS ANY OF YOU STRUGGLING WITH THIS. Scott

First off I added Text Gen in my Telemetry screen (iX12). Then I opened the ESC tab in the Telemetry screen and added some motor info: Poles, cell #. Better success now.

There are couple of Avian apms available in the market. Now, I have a Smart RC battery 3200mAh 3S 11.1V 30C, and NX6 with an AR6610T. What kind of Avaian do I have to use. Also, do I have to use a telemetry. What kind if I have to.

I got a twin timber, updated reciever and since that unlocked it basically i setup the plane in forwsrd programming but now my motors spin backwsrds like its in thrust reverse, idk if that is normal when unlocking the reciever then you have to change it back the right way in textgen

Thanks for the video it's very good. I have been searching for the information on how to get the Ultimate Biplane reverse thrust to work. But the manual is useless. It says reverse thrust is available. I used the roller wheel to look for the menu. But the Avian prog does not come on my NX 10 screen. I guess the 637 stock receiver isn't working with my esc so I can not use this function

How about mode 1 pilots? Any work around for that (besides changing radio to mode 2 to do this)?

I just ordered the new E-Flite D-18 Beechcraft that has a Spektrum Avian dual 40 amp ESC ( SPMXAE0240A ). According to the manual it says you must program the ESC for Thrust Reverse with a Smart ESC Programming Box ( SPMXCA200 ). Your video says you can program any Avian ESC with a newer generation Spektrum radio. I have a new NX8. Can I program the Beechcraft D-18 for thrust reversing from my radio, or must I purchase the Programming Box to do this??, as stated in the manual. Thanks for your answer, I will watch for it.

Well I managed to program thrust reversal on a twin motor plane with two 60 amp Avian ESCs. Both ESC were programmed separately with Rx slot 1 and then both were connected to Rx slot 1 with a Y connector with the red wire removed from one Y connecting to one of the ESCs. Cannot rely on the telemetry however, but no matter, I don't need it for that fast plane, just the timer alarm and voice on the aileron, elevator and rudder rate switches.

Thanks again

Hi im a bit confused about how to connect, i have a 80amp Avian esc that has two power supplies and a 6250 with receiver seem to remember somewhere do i unplug the fan and power my reciver from there yours hopefully

Hello, thank you very much for this usefull video. But I have one problem: I can open programming menu (with the rigt stick), but it is not possible move between the programming options (e. g. FLIGHT MODE, BRAKE TYPE etc.). The transmitter don't react on my moving up and down with right stick. Could you give me any advice? Thank you very much! 🙂

Will that work with my updated dx6e?

Could you put reverse on a slider switch and make it reverse the throttle without moving the throttle stick ??? Thanks

With the new 80mm F-16's, with full fresh battery charge, programed the esc, at full throttle my motors pulsate and very little power is achieved in flight. What could be the issue. Using my DX-18 and it is updated. Both T-Bird and Viper are brand new. I've tried recalibration twice with same result. Pulse 6s 5000 45c.

Do all the Avian ESC's require programming/updating?

Its great it can be programmed from my (DX9) transmitter, but how do I remove that menu from my flight screen?? I dont want to see that menu while flying and monitoring my telemetry menus.

Can I get reverse thrust with a non spektrum reciever? Such as a radio master tx16s?

How do you update the firmware on the fc6250hx.. I need to know the steps. I have a nx8..??

Love the video and the new Avian ESC. Is it possible to do this same thing on a DX6 G2 for the "CH7 - dumby channel/internal channel"? Also where can i find a video on how to set up a Carbon Cub S2 1.3M BNF with my DX6 G2 and have my Flaps working? Is this possible, i know it was possible on the DXS RTF TX somehow.. Thanks

Love your videos Tom! Considering using 2 of the 120Amp Avian ESCs connected to EFlight Power 180 Brushless Outrunners in the Hangar 9 OV-10 with 12S configuration. Plan to use AR20310T receiver. Is this receiver a Smart receiver? Do you recommend an alternative receiver? Notice that this ESC does not support motor reversing. Is there an upgrade planned to include reversing on this ESC in the near future? If so, would both be assigned to the same switch on my Spektrum iX20? All of my current planes and jets are BNF or PNP foamies. This will be first ARF. Trying not to wait till last minute to resource all the parts.

@SpektrumRCvideos

3 жыл бұрын

Hi Dexter. Thank you! :) Currently the Powersafe receivers DO NOT support Smart ESC telemetry... It is in the works but it may likely be a new receiver :( The largest channel count Smart compatible RX at this time is the AR8020T and AR8360T (8 Ch) but more are in the works. ALSO the ESC does support reverse thrust with our latest update for the esc. BUT you do need a Smart receiver to perform this function so until we have a receiver for your application it is kind of a moot point.

My ix14 is up to date according to Play Store, and yesterday I bought the Slow Ultra Stick. Avian Prog is not showing up on my radio, even following your tips...😢

Hi, will this work with the DX8 G2

Hi, the Avian Prog menu is not showing up when I scroll on my DX8e. I just got the new A10 64mm, and it says I should be able to do it. I do have a 90mm Viper from last year, and I was able to get the Avian Prog menu working for that plane, so I don’t know what the issue could be.

Hi can a DX8 G2 program thrust reverse for A10

Can you use four of those controllers on a quad? I'd like to try the heli acro tricks on a drone.

@SpektrumRCvideos

3 жыл бұрын

Possibly... But the serial data and telemetry would not pass thru a flight controller. Essentially they would be seen as regular PWM ESCs.

To put it on your Gear channel, select Channel 5. That's perfect for models with fixed gear.

Great video, and well explained. Love the idea you can update esc without programmer..... Question: will you eventually be able to update your smart receiver too from tx? Or will always need the cable?

@SpektrumRCvideos

3 жыл бұрын

Thanks Stuart. Updating RX from TX is something we are interested in implementing ;) Keep your eyes on our social channels for news and updates

@stuartworrell9442

3 жыл бұрын

@@SpektrumRCvideos Ok great. One more question.... With my NX10 on the way, does that mean I don't need the programmer box to update firmware? Or do I still need it to get latest updates on esc?

@SpektrumRCvideos

3 жыл бұрын

@@stuartworrell9442 Most of the Avian ESCs are now coming with this update BUT there are still some in the wild that will need the update so I would say better safe then sorry and get the updater just in case, at least for the near future.

@old-rcplane-phart

11 ай бұрын

U can program & update any (spektrum) rx via the iX tx's. I do all the time with my 20se.

Can you do a video with the ix12

To reverse motor do you just change motor fro CW to CCW then save.?

@SpektrumRCvideos

3 жыл бұрын

That is one way yes :)

You edit out the most important part! How do you get out of the program mode once your program has been set?! Why did you edit that out?!

Can this also be done with other transmitters such as the TX16s???

@old-rcplane-phart

2 жыл бұрын

Nope! Spektrum ONLY!

Have updated the firmware to the latest on and Avian 80 Amp as installed in my eFlight 1.5m Mustang and the thrust reverse feature is working. I can program from a PC or the programmer, but the TextGen is not showing on my iX12. I have an AR637TA receiver, but I have updated the firmware and it is unlocked. Is there any reason I should not be seeing the TextGen 'Telemtry' on my iX12? Managed to get it to show by going into telemetry and selecting auto-config. It now shows but is inconsistent in letting me into the programming mode. I’ll rebind the receiver and see if that helps.

@SpektrumRCvideos

3 жыл бұрын

Make sure iX12 is up to date. Also it will not let you into text gen menu for esc if low rates are ON, SAFE is on, OR if you have throttled up. Hope that helps

Your thorough and detailed coverage allowed me to implement thrust reverse. Thanks for taking the time!

Hello, I can't get throttle reverse to function from my TX using the AUX2 assigned switch on CH7 on a DX9 (FW 2.07/2.08) and my Avian (SPMXAE1060) ESC 60 A (FW 4.0.21) connected to an updated AR620 (FW 2.42 ). The throw of switch D on CH7 is set from -100 to 100. Telemetry is functioning and I can access the Avian menu from my TX. Any suggestions?

@scanboostarsan8351

3 жыл бұрын

Argh, I missed the "Braketype: Reverse" setting. Now it is working.

i have planes equipped with a3637t recievers paired with a nx8 . Do i need a avaian esc to enable thrust reverse?

@SpektrumRCvideos

2 жыл бұрын

Yes you do

Does anyone know if you get capacity (mAh) used telemetry if you don't have a smart battery? So my setup would be a DX8G2, AR6610T, an Avian ESC and a non-smart battery. If it works I would definitely get a smart ESC, especially with the new motor reversing.

@SpektrumRCvideos

3 жыл бұрын

If your esc is up to date you will get a approx % battery left. mAh consumed we removed from Smart esc's (even if using a smart lipo) because it was too inaccurate to be usable. % battery left is easier to understand and recognize on the fly. Hope that helps!

@philippschlatter938

3 жыл бұрын

@@SpektrumRCvideos Thanks for the quick reply! Would you say the % battery is accurate enough to not have to use a timer? Because I started using a voltage sensor to know when to stop flying more accurately but this doesn't work very well because the voltage drops a lot when the battery is under load, so I'm hoping to replace that sensor. Also can you set alarms for when the percentage is below a certain amount?

Is there anyway to connect this to the throttle for reverse on an airplane and run it like the collective / throttle on a helicopter so that mid point on the throttle is essentially 0 throttle, full up is 100 fwd (like normal) but as you cross the mid point it goes into reverse proportionally so that with the throttle stick all the way down it would be 100% reverse? This would open up some interesting options for 3D aerobatics.

@SpektrumRCvideos

Жыл бұрын

It may be possible by running a mix, but need to do more testing to find a good suggestion. With indoor season around the corner hopefully we can publish a tutorial!

@tyesai

Жыл бұрын

@@SpektrumRCvideos Thank you.

Finally

Do I have to use a smart battery in order to have this menu on my NX8?

@SpektrumRCvideos

2 жыл бұрын

No you do not

Awesome Tom Thanks for the video, I had just asked Jason on last weeks show when this would be coming out and he didn't answer lol... Going to have some fun playing with the reversing on my esc's and i hope that heli auto rotation mode really works as it should. i have never figured out how to make it work right usin castle esc's Edit: I just updated my 15amp avian and tried to get to that screen but i don't see anything. my Radio is on 2.05 and honestly not sure about my AR410 would it not show up if its not up to date also? I am not seeing the Smart ESC option under my telemetry screen. I am guessing that is the one that makes this work?

@SpektrumRCvideos

3 жыл бұрын

Sounds like your receiver needs a update :)

@epoweredrc

3 жыл бұрын

@@SpektrumRCvideos I did the latest update and its still not showing up. my last screen is just blank.

Ok so I just got a night timber x I also just upgraded to the nx6 with that said can I use full span ailerons reversing and safe at the same time or will I have to just have only as3x

@SpektrumRCvideos

3 жыл бұрын

Yes you can :) Put safe select on Gear(ch5) and Reversing can be on the extra 7th Channel

@Badabupi

3 жыл бұрын

@@SpektrumRCvideos no you can‘t, because the full span ailerons are using up the ch5 and ch6?

@SpektrumRCvideos

3 жыл бұрын

@@Badabupi Ahh you are correct, sorry for the confusion. Looks like you need more channels on your tx

Is there any way to fine tune the ESC/Motor timing. Not just the preset 5,15,30 on the avian 120???

@SpektrumRCvideos

2 жыл бұрын

At this time no. But it is something we are looking into

@Strankon

2 жыл бұрын

@@SpektrumRCvideos well, while spektrum is “looking into it” I’m gonna have to purchase another ECS that is more compatible with a 28 pole motor.

Do I need a Special battery to run the Reverse Thrust or can I use a normal 6s 5000 Lipo Battery? Thank You.

Is it possible to use the thrust reverse form an Avian ESC with another receiver? I use Graupner Hott.

@SpektrumRCvideos

2 жыл бұрын

It is not

I put the Avian 60 Amp Brushless Smart ESC in my E-Flite Air Tractor and it causes the Elevator and Rudder servos to glitch. Had to go back to the stock ESC until I figure this out.

@LoveRC

3 жыл бұрын

Actually found out the Air Tractor does not have the newer metal geared servos on the rudder and elevator. I had to go into the forward programming on the transmitter and set the frame rate on the rudder and elevator to 22ms.

@MikeSarni

3 жыл бұрын

Ok so it was fine once you went back to 22ms? because I'm getting the air tractor today and I'm putting an avian 60 amp ESC in it I have the nx6 and I know you could change frame rate I wonder if it Just defaults to 22 ms though..... What radio are you using the new nx6? Because then that would explain the freaking out on the rudder and elevator sevos. There was a problem/bug with I think five or six air receivers where elevator and rudder would twitch every 10 seconds... definitely couldn't fly with it and it was like clockwork every 10 seconds 🤷‍♂️ anyway horizon hobby just actually came out with a release about a month ago and It fixed that issue for the NX series....took me a while to find this out but I had bought a new citation longitude EDF UMX and I couldn't use it because I had this problem ... After pulling hair out and doing a crap ton of research for a few days and buying new reciever/2 new servos, I actually found this out through research online and looking at NXseries change logs( December's fw did say that it was a problem)... I was pretty much done at this point because new parts didn't work I couldn't figure it out and then binding to my old DXE for shits and giggles it worked perfect🤦‍♂️o🤦‍♂️🤦‍♂️ s right then and there i knew it was software.... after the newest update it was good to go ....but yea I was initially bummed couldn't use my new aircraft it definitely sat for a good while 🙄

@LoveRC

3 жыл бұрын

@@MikeSarni I am on a DX8 Gen 2 and it defaults to 11ms. That caused the glitch. The two servos in the Air Tractor are not the upgraded ones the Timber X has so they need to be set at 22ms. I'm not sure about the NX6. The problem will be obvious if you have the issue. If it is, just go into the forward programming and set those servos to 22 ms.

@MikeSarni

3 жыл бұрын

@@LoveRC okay cool man .....will the stock air tractor receiver actually let you access forward programming? Or do we have to unlock the receiver on the computer first

@LoveRC

3 жыл бұрын

@@MikeSarni sorry I had the numbers backwards ( corrected them in the message above) and the stock ESC does not have the problem. I put in the Avian ESC and had the problem. The servos were glitching. So... I updated the receiver to unlock it. I was then able to use forward programming to change the servos to 22ms.

Getting the night timber with reverse thrust. Manual doesn’t help. How do I program reverse thrust option to a switch with my dx7s.

@SpektrumRCvideos

3 жыл бұрын

Set Aux2 to a switch of your choice, that should do it.

I have a Blade 330s and a NX8, Im not able to get the ESC menu to come up. I do not have the esc programming box to know what firmware my esc has. Is it more than likely the esc firmware needs to be updated first?

@SpektrumRCvideos

Жыл бұрын

Correct, the esc firmware is likely out of date. That said I personally would not recommend messing with the settings on the esc unless you are trying to use it in a different model.

@russgreer4012

Жыл бұрын

@@SpektrumRCvideos when I flip from normal mode to flight mode 1 or 2 my head speed bogs down and the heli drops unless I flip back to normal. This is with the recommended pitch and throttle curves per the the 330s manual (BNF version)

@SpektrumRCvideos

Жыл бұрын

Hmm that could be a couple different things... weak battery or too tight of gear mesh I would check first.

I updated my DX8 G2 back in September, and I just got all my Avian ESC's up to date. Will there be another Tx firmware update to be able to program the ESC from the Tx?

@SpektrumRCvideos

3 жыл бұрын

You should be good to go :)

@charliemarchiony7914

3 жыл бұрын

@@SpektrumRCvideos I'm trying, but the menu doesn't show up. I'm using an 80 amp ESC, AR620, and Smart battery. The AR620 is up to date

@charliemarchiony7914

3 жыл бұрын

It's not one of the options in the telemetry menu, or fwd programming

@SpektrumRCvideos

3 жыл бұрын

@@charliemarchiony7914 If you scroll all the way to the right while on the main screen it should appear there. It will not show up in Fwd programming or the telemetry menu with the latest TX firmware

@charliemarchiony7914

3 жыл бұрын

@@SpektrumRCvideos I have the main screen, monitor, flight log, rx voltage, smart ESC min/max, smart ESC, battery info, and the smart battery screens. I'm using an AR620 from February, though it is updated. I've also tried with an updated AR637T, but the last screen it shows is Vario.

I just ordered two 60amp Avian ESC's and two 40amp to do reverse thrust on a Freewing AL37 and Eflite 64mm A-10. Both have smart receivers and I’m using a DX8e Gen2. Do I need to program each ESC separately or will they both program to be the same during the process demonstrated in this video if they’re connected through a Y?

@kalephgreen4375

3 жыл бұрын

This...literally for the same thing?^^^^^

@bucky32555

3 жыл бұрын

@@kalephgreen4375 I got a more in depth answer on the AL37 and it wasn't possible since you need to run the ESC's together. I ended up putting JP Brakes on it which works amazingly well and has saved me from several landings that would have gone off runway. I paired the brakes with the Assan AG63 side slip gyro/brake controller and the results are incredible! perfectly straight takeoffs with no trimming required and fast braking in a dead straight line with no steering input needed.

@kalephgreen4375

3 жыл бұрын

@@bucky32555 I actually just ordered jp brakes day before yesterday.. but with the jp controller. How are yours setup? All four mains? Mains and nose?

@bucky32555

3 жыл бұрын

@@kalephgreen4375 I have the 65mm with 4mm axle which fits in perfectly. I’m only running a single jp brake wheel on each main and not using the stock mains. I didn’t think replacing the axle on the JP’s was worth it. Probably 20+ flights and it’s working great.

@kalephgreen4375

3 жыл бұрын

@@bucky32555 I just ordered two sets of 60mm mains and 40mm jp rollers for the front (want to try to lower it, and have it look a bit more scale) .. you think it would still work correctly splitting two brake wheels per channel? I'd imagine it would be half the effort, but it's split between 4 wheels..🤔

Where can I find the menu “avian prog”in the IX20? I’ve updated to the latest firmware in the play store, but it’s from July 2020 V1.03.12

@SpektrumRCvideos

3 жыл бұрын

It is not exactly a menu in the settings, but a telemetry screen that shows up when using smart esc with the latest update. Simply swipe all the way to the right while everything is connected and it will be there. The telemetry field is called Text Gen. Hope that helps!

@mattiaseriksson5728

3 жыл бұрын

@@SpektrumRCvideos ok, so I just have to order the SPMXCA200 to update the ESC I bought a week ago to get the firmware to be able to not use the SPMXCA200 to program the ESC in the future...

@SpektrumRCvideos

3 жыл бұрын

@@mattiaseriksson5728 Correct. The programming box is also the interface for updating

So I have the v1200 bnf and ix12 I can do this ?

@SpektrumRCvideos

3 жыл бұрын

Yes you can

@gavinwilkins5466

3 жыл бұрын

How I can't seem to get it to work

Does thrust reverse work with futaba controllers

@SpektrumRCvideos

Жыл бұрын

No, it is exclusive Spektrum technology

@firstphoton655

Жыл бұрын

@@SpektrumRCvideos I have a night radon and it's stuck on a3x mode and I can't get it back on safe. I binded it correctly and put both sticks towards the center and flick the switch five times back and forth no matter what I do safe won't activate any tips im using a dxs

Is the reverse function with other receiver brands or only spektrum?

@gonzo2779

3 жыл бұрын

Same question here☝

@SpektrumRCvideos

3 жыл бұрын

@@gonzo2779 Spektrum Only, It is a function of the Smart telemetry that makes this possible

@DrCho-en9cd

3 жыл бұрын

@@SpektrumRCvideos Really frustrated. I bought Draco PNF because of reverse thrust to use in my Futaba system. There is no other way to use reverse thrust with Futaba?

@SpektrumRCvideos

3 жыл бұрын

@@DrCho-en9cd Not that we have setup. Someone might be able to find a way to hack the SRXL2 data stream so it can be done but really it is part of our serial protocol (SRXL2) between the esc and the rx/tx. Might be a good idea to grab a NX8 for your Horizon Hobby aircraft or you gonna be missing out on a lot of the perks :)

@DrCho-en9cd

3 жыл бұрын

@@SpektrumRCvideos OK, I've ordered Spektrum 8ch receiver for Draco, cause I already have iX12, too. Thanks anyway.

Tom what is active fw? Thanks

@SpektrumRCvideos

2 жыл бұрын

It stands for active free wheeling. Essentially it ramps down the rpm of the motor when the power is reduced to zero, encouraging the prop to keep free wheeling while in a glide etc.

why cant I find this menu AVENT PROG ON MY DX8E IN TELEMETRY?

@SpektrumRCvideos

2 жыл бұрын

Could be the transmitter needs a update.

Hello all hopefully I can get some quick help with a small situation. I am running a Avian ESC with a AR 637 receiver and I'm wanting to activate throttle reversing. Supposedly with the latest Ix20 firmware I should be able to program the ESC via the transmitter. I watched the video on it and the ESC Prog. Option It's not showing up anywhere that I can find. Does anyone know what I need to do to be able to program the ESC via the IX 20 transmitter?

@SpektrumRCvideos

3 жыл бұрын

Your ESC may need an update. There are links in the video description that explains how :)

@erickessler6708

3 жыл бұрын

@@SpektrumRCvideos I just updated my AR637T and Avian 60 amp esc and I still do not see a way to program/update from my IX20 nor do I see a way to turn on motor reversing in the programmer or software. What am I doing wrong?

@SpektrumRCvideos

3 жыл бұрын

@@erickessler6708 make sure you are running V4.0.21 from this download www.horizonhobby.com/on/demandware.static/-/Sites-horizon-master/default/dw28558c9c/Manuals/Spektrum-SmartLink-ESC-Update-and-Programming-Instructions.pdf

How does the reverse work on jets and landing? 😬

@charliemarchiony7914

3 жыл бұрын

With the flip of a switch, it brakes and stops the motor, then spins it up in the opposite direction. Probably a good idea not to flip that switch until touchdown

@SVGERichy

3 жыл бұрын

@@charliemarchiony7914 i meant on the ground not in the air

@SpektrumRCvideos

3 жыл бұрын

It works quite well! Now it can depend on the aircraft and how the inlet is setup but on a model with no cheater holes it works great as a landing brake :)

@charliemarchiony7914

3 жыл бұрын

@@SpektrumRCvideos Will it work on the F-4 80mm, with just the one cheater hole on the belly?

@SpektrumRCvideos

3 жыл бұрын

@@charliemarchiony7914 I think so. It is worth a try :)

If I go to forward programming only auto giro is showing up

@SpektrumRCvideos

2 жыл бұрын

What receiver?

Spmxae1100 esc Can this be reversed

Just updated my 120a and the motor is spinning backwards now. Tried changing the motor direction option but it doesn’t have any effect. Can’t swap the motor wires because they’re direct soldered and buried. Even setting a channel thrust reverse doesn’t work. Tried factory reset as well with no luck. Any suggestions? Using an ix12

@SpektrumRCvideos

3 жыл бұрын

Hi Donald, Make sure you are hitting exit w/ save when you change the motor direction. Changes will not take affect until you save the changes :) Hope that helps!

@donaldvail23

3 жыл бұрын

@@SpektrumRCvideos I changed the settings from both the esc programmer alone and computer with no luck unfortunately.

@SpektrumRCvideos

3 жыл бұрын

@@donaldvail23 Odd, let me do some digging on my end for some ideas. Stand by

@SpektrumRCvideos

3 жыл бұрын

@@donaldvail23 looks like you found a bug! We have it in our log and it will be fixed in the next esc update. I would say in the meantime swap 2 wires. Also we did determine that thrust reversing does work propperly so you could just use that to drive the motor one way or the other ;)

@donaldvail23

3 жыл бұрын

@@SpektrumRCvideos Thanks for the update. I’ll have to try and figure out why the motor reversing isn’t working then. Is it possible to downgrade firmware if I can’t get it working? I still have the old version of the programmer on my pc. there’s no bullet connectors between the esc and motor, the wires are directly soldered, I’d really like to avoid having to tear the plane apart to get to the wires are re-solder them.

Can this work for DX6E?

@SpektrumRCvideos

2 жыл бұрын

Yes it does :)

What is Surge SW?

@SpektrumRCvideos

2 жыл бұрын

That sets the esc to "pulse" the motor when it reaches LVC

@SunriseRCAviator

2 жыл бұрын

@@SpektrumRCvideos Like on the UMX planes?

@SpektrumRCvideos

2 жыл бұрын

@@SunriseRCAviator Correct

I have IX14 and NO avian prog Screen no matter what. Man frustrating …

I just wannna fly not get a IT degree damn

@ralphfrasier2079

2 жыл бұрын

@Ruger 09: I agree sir! I am transitioning from the cut and dry BNF to Smart RX, ESC, etc. On a couple of PNP Models. It is abit over whelming!

Why you guys never point out which wire lead is the actual reverse wire lead?! You demonstrate the function, sure! But you don't show which of the wire lead to have to put where, besides the throttle lead. Or is forward and reverse is from the single throttle lead only??

What update number should I have, updated 2 weeks ago and now at 2.07.

@SpektrumRCvideos

3 жыл бұрын

2.07 is the latest at this time :)

First comment again haha