Audi S3 Rear Brake Pad & Rotor Replacement DIY (2015-2020 Audi MQB A3, S3, TT)
►Replacing the rear brake pads and rotors of your MQB chassis Audi A3, S3, or TT is essentially the exact same process regardless of the car. If your brake pads or rotors are visually worn past their usable life, or if you're experiencing brake squeal or the rear of your car shuddering under braking, it's time to replace these components.
Replacement of the Audi A3, S3, and TT brakes couldn't be more straightforward and is a job that nearly anyone can tackle in their garage or driveway at home. It requires minimal special tools, all of which are outlined in the intro of this video.
Follow along as Aaron Davis, FCP Euro's Audi Catalog Manager walks us through the step-by-step process to replace the rear brakes and rotors on this Audi S3.
00:00 - Intro
00:48 - Tools Needed
01:46 - Electronic Rear Caliper Opening Procedure
03:02 - Wheel Removal
03:16 - Rear Caliper Removal
04:41 - Rear Caliper Carrier Removal
05:04 - Rear Rotor Removal
06:00 - Rear Hub Prep
06:11 - Caliper Opening Procedure for Non-Electronic Parking Brakes
07:54 - Rear Rotor Install
08:40 - Rear Caliper Carrier Install
09:13 - Rear Pads/Caliper Install
11:15 - Rear Wheel Install
11:43 - Electronic Rear Caliper Closing Procedure
12:53 - Wrap-Up
Buy This Kit Here: www.fcpeuro.com/products/audi...
This video applies to the following vehicles:
S3 Audi 8V
Position: Rear, For Models w/ 310mm Rear Brake Discs
2015 Audi S3 Premium Plus Sedan 2.0L L4 CYFB Automatic Dual Clutch Brake Kit
2015 Audi S3 Prestige Sedan 2.0L L4 CYFB Automatic Dual Clutch Brake Kit
2016 Audi S3 Premium Plus Sedan 2.0L L4 CYFB Automatic Dual Clutch Brake Kit
2016 Audi S3 Prestige Sedan 2.0L L4 CYFB Automatic Dual Clutch Brake Kit
2017 Audi S3 Premium Plus Sedan 2.0L L4 CYFB Automatic Dual Clutch Brake Kit
2017 Audi S3 Prestige Sedan 2.0L L4 CYFB Automatic Dual Clutch Brake Kit
2018 Audi S3 Premium Plus Sedan 2.0L L4 DJJA Automatic Dual Clutch Brake Kit
2018 Audi S3 Prestige Sedan 2.0L L4 DJJA Automatic Dual Clutch Brake Kit
2019 Audi S3 Premium Plus Sedan 2.0L L4 DLRA Automatic Dual Clutch Brake Kit
2019 Audi S3 Prestige Sedan 2.0L L4 DLRA Automatic Dual Clutch Brake Kit
2020 Audi S3 Premium Plus Sedan 2.0L L4 DLRA Automatic Dual Clutch Brake Kit
2020 Audi S3 Premium Sedan 2.0L L4 DLRA Automatic Dual Clutch Brake Kit
SUBSCRIBE: kzread.info?sub_c...
Get free parts from FCP Euro:
www.fcpeuro.com/page/lifetime...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com/
Пікірлер: 80
FCP Euro thanks all for all those DIY projects it really helps!
if anyone is struggling with getting the m14 bolts off just remember you don’t need to take the caliper breaker off for a rotor change.
Great helpful video.All the best from the UK👍👍.
Nice vid, easy to follow, good for example thsnks
Great tutorial video
You make that look easy! I remember doing my 2016 A3 and I swore way more than any other brake jobs i have done lol not much space for the ratchet for the caliper carrier to remove it let alone break it free.....ended up padding the metal with a rag after smashing my fingers lol good times 🤣🤣🤣
Great video, thank you!
@fcpeuro
Жыл бұрын
Thank you for watching!
For a Audi A3 8V TDI S-Line(did the rears today, Brembo discs(rotors) and pads) you will need a stubby 7mm socket for the top and bottom of the caliper bolts(because the suspension parts behind are to close for a normal one(so the one i bought was useless!. Good job i also brought a 7mm allen key!). You have to take off the 2 carrier bolts! as the disc will not just slide out!(like they can on some S3's). I used the M14 spline tool on a 10" breaker bar with a swivel head going in from the top right for both the bolts. Going in from the top right there is loads of room with the aid of the swivel head to get the angles(saying that i also went in from the top right when using my torque wrench to tighten them back up"). With a steady hard push down they undone easy IMO(i did have my Weetabix that morning!!). With everything going really well, i even painted the calipers after :). THX for the video it helped me alot before doing mine
@curttheboywonder
2 ай бұрын
Doing my q3 2020 rears rn and can’t find the brake carrier bolts to get off to replace pad. Hopefully this video helps
Thank you
excellent guide 👍
@fcpeuro
2 жыл бұрын
Thanks Jason!
Excelente! Thank you!
@fcpeuro
8 ай бұрын
You are welcome!
Great explanation.. but I’d add that you should pull the slider pins out of the boots and clean and re grease them.. and good practice to line the caliper boot with silicon grease.. .. gonna buy my rear pads and rotors this week
@macauleyh5
8 ай бұрын
I just replace them as they're only £25-30 for front & rear slide pins
Very good video , thanks for your time!
@fcpeuro
2 жыл бұрын
Thank you for watching, Thomas!
How do you do the rear electronic brake? I’m so lost. I need help because I think I’m missing the main thing to do this. I have a 2015 Audi a3
This video is insane. I just did the rear brakes on my RS3 without a vehicle lift on the original parts. Different experience.
@lukealiciouss
9 ай бұрын
I’m about to do my rear brakes on my RS3 also. How did it go? did you need a scanner? I heard you can just apply voltage to the motor to release it
@cmanzii
5 ай бұрын
@@lukealiciousshow did it go? bout to change mine, do you need the scanner?
@11Greatness
29 күн бұрын
@@cmanziiI used the scanner. Yes
Bro please do a video on the tie rods. Got an a3 and these tie rods are weird
Thanks man, do you have to bleed it after replace the brake pads?
He has such a perfectly round head!
Wait these rears look like the Honda 10th gen one. There is a way they do it manually for the e brake
I did this and now have a electronic parking brake malfunction light, do you have a solution for this?
almost great work. no manufacturer orders to smear the hubs with grease under the disc. this creates micro wobbles of the rotor. It is not meant to be taken off every month. just clean it mechanically & chemically so one flat surface is facing another uniformly. if You still want to do it at least turn the rotor on the hub several times to evenly distribute the grease.
Do you really need the scanner to unlock the electronic parking brake or just need to turn off the parking brake to change the pads?
Can you post torque specs in the description
FCP Euro.....Drilled Vented disks have a left and right part number as they are not the same on both sides...and in your vid you installed a right hand disk on left hand side of the car...
Can this process be done in neutral to bypass the electronic handbrake? Just do 1 side at a time and use someone to push the pedal in when tightening the wheels back up?
@seano51
9 ай бұрын
No, placing it in neutral does not fully retract the motor. I tried it.
What type scaner relatively priced can I get to turn off the electronic rear brake or type is the one you used
@Satori_Hishumetse
4 ай бұрын
Obdeleven
If you electronically open the piston; do you need to screw it back in or can you just compress it normally?
@fcpeuro
Жыл бұрын
You would need to reset it back to its normal operating position.
I’ve watched where the caliper carrier doesn’t need to be removed. The rotor can just pop out.
Anti squill grease to me is copper grease in the UK
Cant i just open the ebrake inside the car?
The rear brake carrier needs to be torqued to 90n.m and then another 90 degrees thereafter, otherwise, great video!
@bystander1489
2 жыл бұрын
Haha another you tuber torque spec if you think that happens in garages your dreaming 🤣
@Twiisp
2 жыл бұрын
@@bystander1489 VW/Audi Dealer Tech of 6 years, seen my fair share of these coming loose and flying off while the customer was driving👍
@shishuali4821
2 жыл бұрын
The rear carrier does not need to be touched on these MQBs the rotor just slides past
@Twiisp
2 жыл бұрын
@@shishuali4821 not all, some of the Tiguans and golf's can't slide out, it's dependent on the motor/brake setup that they have
@shishuali4821
2 жыл бұрын
@@Twiisp I see, looks like I got lucky with mine, thanks for the info 👍
So on my s3, I have electronic ebrake, I will be using obdeleven to open and close ebrake. Do i still need to use that manual tool to push piston back or no? Thanks
@deeezobrown
2 жыл бұрын
Just did the same on my golf r (e.g. same rear brakes as s3). I had to use the tool to push back the piston even when I opened vis OBD11.
@sunilraj7692
2 жыл бұрын
Yeah. Scan tool just rewinds the motors so you have space to push the pistons back.
@connaghtakairangi6935
Жыл бұрын
Can you push the piston back even without disarming the electronic brake?
@overknight5278
Жыл бұрын
@@connaghtakairangi6935 no, its really tough and wont go anywhere. Thats how it was on my 18 fusion with the EPB. Did these on an A3 yesterday and also had a hard time with them open/in service mode as well (im rewatching the vid b/c i got a fault lol) but it works?
@simonc6758
Жыл бұрын
What if you don’t engage electronic parking brake and leave it in neutral ?
Is this the same for a 2016 A7?
Could these be fitted to rs3?
I did mine on my 2019 A3 8v.5 using OBDeleven, worst part was buying the tools 😂
Note for anyone doing this at home. I did this on my 17 Audi S3 and I still had to use the brake winding tool to release the caliper. I first turned the caliper piston anticlockwise a few turns and then turned it clockwise. This fully seated the piston.
@AlejandroHernandez-fy4qh
Жыл бұрын
Did you use vagcom ? Or any scanner tools ? I don’t really want to spend the money on something I’m not going to use often? But if so I’ll do it if I have to just curious to know if you did that ?
@brendonv101
Жыл бұрын
@@AlejandroHernandez-fy4qh yeah I used vcds/vagcom.
@iHadWaterForDinner
Жыл бұрын
@@AlejandroHernandez-fy4qh im about to do the same and have the same questions...
@egert1064
11 ай бұрын
@@iHadWaterForDinner i had the aliexpress copy scan tool for releasing the brake. Worked fine but still had to push the piston in also manually. Its in forums and apparently part of rostec instructions to push it in manually. No need to turn it any special direction. Old pad and screwdriver and it will go.
@iHadWaterForDinner
11 ай бұрын
@@egert1064 thank you :)))
why not just pop it in neutral?
@seano51
9 ай бұрын
Neutral does not fully retract the piston/motor. I tried it.
I can’t wait to buy an M14 triple square socket and then probably never use it again! Effin Audi 🙄
@mattdole275
Жыл бұрын
the one i bought i can't fit a ratchet behind.. not sure how they made that so easy. but i feel this on a spiritual level
@mitchlachs286
Жыл бұрын
After actually doing this, you really don’t even need to take the triple square carrier bolts out. I did the job without needing to take them out after all
@seano51
9 ай бұрын
@@mitchlachs286Correct, you don't have to remover that bracket to remove the rotor.
@DutchxPR
2 ай бұрын
Yeah if you tilt the rotor you can pull it out with out removing the bracket. Just be careful putting the new ones in you can scratch them
@care2000
Ай бұрын
@@DutchxPRsorry just wanna clarify, you can change the rotors without removing the caliper carrier? I struggled for an hour trying to get those M14 bolts to budge but I have no space for torque lol. , so I gave up.
Question, with these rotors can you put Ate semi compound or it must be Ate ceramic pads? Looking for longevity, low noise and stopping power right of the start.
@fcpeuro
Жыл бұрын
You can pair them with whichever pads you like!