Attempting To Reverse A Non-Reversible Motor
amzn.to/2jw8nDr Soldering Station With Heat Gun
amzn.to/2ncIf5o Heat Shrink Tube Assortment (Handy)
amzn.to/2Aip1At Bearing Lubricant
In this video, I take a look at a motor to see if I can reverse it.
Help support Doublewide6 Repairs LLC by sponsoring his Patreon account
/ doublewide6
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.
Пікірлер: 35
You sure have skills, Bob!! I rarely see one of your videos when I'm not reminded that the biggest challenge I face is simply giving something a try. A big part of these projects is the satisfaction you get from making something work. Thanks, Bud!!
I seem to learn something with every video I watch of yours...thanks for making them. God bless you and yours.
You learn something new every day!!!
Reminds me of hysteresis loops from school. Back in 75 -76 I took electronics at a technical college (telecom). Reverse the magnetism. Wow you are very good at realistic demo's.
I bought a used electric concrete mixer off Craigslist and the way the paddles in the drum were angled it was turning in the wrong direction. It has a non-reversible motor. Found this video and tried this. Problem fixed! Thanks!
Thanks for your time & the education!
Heck, I just learned something too!
Awesome video on motor rotation keep them coming... the motor I have has two smaller winding wires to each lead rather than one, so would I have to swap two and two or just one. If so which of the two gets swapped...thank you
Txs for the video,does it reverse if you just switched the main wires hot and neutral ?
😎🇺🇸👍 Very Interesting 🔌 learn something new every time we tune in! Thanks 🙏🏽
Cool video thanks I just learned something for sure
So if i just find where the smaller wires attatch and switch thise from their original im good ? Is that basically all you did? My motor has a start capacitor and a run capacitor, does that matter? It almost seems to me i coukd switch the wires in the switch capacitor and that woukd work. Im lost. I was so excited to upgrade my table saw to a 2 hp motor to find it runs in the wring direction and im lost. So much info in youtube but its over my head
cool video as usual, what about making a motor reversible to fix a drain auger setup? my 1/3 hp unit is out and if I didn't need reverse it would already have a weed eater motor on it.
So the connection that had two wires, you only swapped the thinner wire, right? (Or did you swap both?)
Why didn't you remove it from the case put it in the other side and there's nothing to do after that except to put the fan blade back on.
that should be a good motor I didn't know what it took to reverse a ac motor..
Why not just switch the wires on the capacitor?
All da matrix n could just switch on d capacitor
Now see, this is why you have a You Tube channel and I don't. I would have just mounted the motor on the other side if it was going the wrong direction and, If I needed to remove heat shrink tubing, I'd have put it in the freezer to expand it. ;-)