Atomstack A20 Pro- Engraving Acrylic the Easy Way!
Тәжірибелік нұсқаулар және стиль
Atomstack A20 Pro- Engraving Acrylic Made Easy!
Welcome to the Laser Channel- Learn, Create, and Share!
In this video I’ll demonstrate how to engrave acrylic step by step.
This is a detailed video to show the settings I use, how I got the settings and then creating a fun LED acrylic light!
Product links (bookmark them for later!):
Atomstack:
shareasale.com/r.cfm?b=180857...
Product links are tested safe and there's no extra fees if you purchase through the link!
Atomstack F2 Large Honeycomb:
amzn.to/3Sv4KxA
LED Base in Video- purchase acrylic separately:
www.jpplus.com/acrylic-led-light-base-with-wireless-remote
4 Piece LED Complete Set:
amzn.to/3IAUcIr
(this is a popular option)
Wooden LED Base-purchase acrylic separately:
amzn.to/3ZqrVvk
Dollar Tree Black Poster Board:
www.dollartree.com/black-poster-board-22x28/193024
Пікірлер: 27
Done like and subscribed. Thank you for making all your engraving video
@thelaserchannel1
7 ай бұрын
Thank you!
Thank you for taking your time to make this interesting video. I enjoyed it very much.
@thelaserchannel1
Жыл бұрын
You're welcome! Happy lasering!
hello , i have the atomstack s20 pro, i purchased the extension kit, wiring was straight foward, but i have one single black wire that i'm not sure where to place it, it goes, i think to 1 of 2 ports, one is 5 volt and the other is 12 volt. it comes from the power switch. any ideas anyone ??
Hi, I have an atomstack s20 max. The power of the laser is 18-20w. They cannot cut plexiglass (acryl) 3 mm at all. Is the problem that the laser power is low, or did I not set good parameters for cutting? I use the lightburn program
@thelaserchannel1
2 ай бұрын
Hi- there's a couple of factors- Black cast acrylic cuts the best- white and defiantly clear do not cut with any amount of power. Slower speeds and medium to higher power settings tend to work best.
thanks a lot for that video. I have a S20 pro and i've a little scare to applied over the acrylic. My english is not good... could you indicate the material that you put under de acrlylic? thanks again for your response
@thelaserchannel1
Жыл бұрын
You are welcome. Under the acrylic is black poster board- it is a very black thin carboard.
Hi, I'm new with this laser engraver. Is it possible to cut the clear acrylic with this Atomstack A20 Pro?
@thelaserchannel1
Жыл бұрын
Hi! No, it's not possible to cut clear acrylic any laser diode machine; it does not matter the brand or power output. The laser diodes operate in a range that does not affect clear acrylic for cutting. To cut clear acrylic I recommend a Co2 laser- cuts clean through. Thanks for watching!
Hi there how thick is the acrylic you used in this video? I have melted mine 🙂
@thelaserchannel1
4 ай бұрын
Hi- I used 1/8" (3mm) acrylic. I ran a materials test chart to find the best settings for my setup. Thanks for watching and best wishes.
Hello! I am trying to cut acrylic but having a hard time finding my bearing and have been burning the acrylic. I have an atom stack x7 pro
@thelaserchannel1
8 ай бұрын
Acrylic can be tricky. What type and color do you want to cut?
@ursulich
8 ай бұрын
It’s clear and I have a black bottom for contrast
@thelaserchannel1
8 ай бұрын
@@ursulich Clear acrylic is not able to be cut by a laser diode. To cut clear acrylic a Co2 laser is needed. Here's video with an entry level Co2 laser: kzread.info/dash/bejne/iKKirrGglN3cgZs.html
Can you etch say 2mm into black acrylic?
@thelaserchannel1
5 ай бұрын
Yes- the A20 Pro can etch 2mm into black acrylic- it can also cut through 1/8 inch (3 mm) black acrylic with ease!
do you show how to engrave acrylic using GRBL software
@thelaserchannel1
Жыл бұрын
Hi- no, I don't show the laser machines using GRBL. I use LIghtburn on all my machines.
@tcollins6969
Жыл бұрын
@@thelaserchannel1 is cast or extruded acrylic
@thelaserchannel1
Жыл бұрын
@@tcollins6969 It is cast acrylic from a quality and reliable source- Houston Acrylics. I'm not affiliated with but I order all my acrylics from them. Extruded acrylics will crack, bubble, or burst- it just doesn't work.
Hi... can i use WD40?
@thelaserchannel1
Жыл бұрын
Wd40- I'm thinking you mean for cleaning correct? I haven't tried WD40 for cleaning- my hesitation to use it on acrylic is maybe it would fog or crack the acrylic over time.
@user-qv1rg5kr4k
Жыл бұрын
Oh i see. Can i know that alcohol u use same as perfume alcohol sir? Because i dont know how type alcohol i want to buy
@thelaserchannel1
Жыл бұрын
@@user-qv1rg5kr4k I use Denatured Alcohol- it's also know as stove fuel.