Buddy, you need to put your hands as far apart on the handle as you can and then turn, it’s called leverage. The way you were trying to screw it in, you may as well not have even put a stick through the eye. 🤦‍♂️

@thomasknox2325

6 ай бұрын

Maybe you need to make your handle longer and move your hands out

@kalepotter9451

5 ай бұрын

He claimed he didn't know what he was doing. Calm your tampon.

@jamesgulliver817

5 ай бұрын

Fucking ay to that. So frustrating to watch!

@danylo6532

3 ай бұрын

Hey, I had pretty much the same problem. The tip was a huge help, thank you. Even though I think you could have been nicer about it, thanks a lot anyway.

@unzin-rb6pm

2 ай бұрын

yea... this bloke ain't gettin' it...

Hi. Thanks for video. Few comments. 1. Failure to properly restrain your working wood means you cant apply max force. 2. Increasing your lever reduces the force you must apply. You kept your hands against the metal of the drill. You had to apply maximum human force. Put a 2 foot stick in the scotch eye as a “T” or have 90% of the stick on one side. Reduce your human effort 3-7 times by using the lever properly. 3. When buying a “cheap” $15 unsharpened chinese implement…learn to sharpen it with a metal file in less than 5 minutes. Any woodworking tool MUST be sharpened regularly….Or buy a $150 razor sharpened tool that you will still have to sharpen at the end of a full days work. 4. Buy the cheapest tool that meets your maximum expected torque application and the metal is tough enough to hold an acceptable sharp edge for a defined number of uses. Otherwise you’ll cuss when you have to sharpen your $3 knockoff after each 2 inches of drilling OR when you realize your $175 Scotch Eye fell out of you pack while on the move through the woods.

@vitalijusra6125

5 ай бұрын

and come to think of it, ever heard drilling smaller diameter first? What's with the suffering

Not doubting they are not of the best quality, but there is some serious user error going on here. You keep putting your hands almost at the center of your handle and I think that is probably your biggest issue. Also, whenever I use them for building a shelter, or something of that nature, I usually have a much longer piece of wood I am drilling into. That little chunk of wood will be really hard to keep from moving. Basically you are fighting yourself.

Just found you channel today and am working through your play list. I bought the same 1 inch auger you have about two months back (September 2023) and immediately gave it a try. I was trying to bore holes in various sticks to make a bushcraft chair as a back yard project. Ran into the same troubles you did, then realized what both you and some of the comments here talked about: wood was super dry and it was hardwood (oak). At least I was trying to cut into the side of the grain, which you demonstrated was a lot easier. (Thanks for that - will be useful knowledge down the road.) Because of this video and the comments, I've learned a lot. I especially like the bar of soap idea - wish I had thought of that! I'll use it the next time I give the auger a whirl. This is a tool that needs to be actively learned, I think, unlike a power drill. (Side note: another item I'm trying out for drilling holes when bushcrafting is the old school bit and brace. Similar cutting principle, but different mechanical layout.) Oh yeah, one final thing... you mentioned you thought the scotch eye on the 1 inch might be good for making dowels. I can confirm that it works from experience. Batoning it, tapered side down, does the job and it works even better on a stick you trim slightly beforehand. (I made the handle for the auger from a piece of the same dry oak I was boring through and it worked fine.) My only concern was being careful of the weld point, since it might weaken over time. Batoning on the top of the eye and then shifting the blows onto a stick laid across the shank once the eye got further down seemed to work OK. (Hopefully that protects the weld a bit. Wouldn't want to use anything other then wood or a rubber mallet to hit it with though.) Nonetheless, it will let you make dowels that can be used to peg into the hole the auger cuts. Also, that cylindrical leather piece you left at home is designed to slip over over the auger bit to protect your hand so you can use it as a handle when batoning a dowel. The site I bought from had pretty lame instructions and the use for the cylinder wasn't made clear at the time, but I eventually figured it out. I also saw your video on the Grohmann belt knife. Very helpful! I was gifted one by my son-in-law and I have come to really love that thing. I was especially happy to see you using it for batoning and striking ferro rods. Excellent review. Anyways, thanks for your videos. Cheers from Coquitlam B.C.

You tried using the 1.5 inch auger on hard wood. That was oak. You will never get that thing through. You have to use soft wood that is still green. Even then, the smaller size will be a lot easier.

@coast2coast00

Жыл бұрын

You need like a 4 foot log and a 2 foot handle. The screw kept pulling, so I think it would make it through eventually. If you had a 1.5 inch power drill, you wouldn't' think for a moment you could hold that piece steady with the sides of your feet.

Hey Jes, the tapered edge is for sizing the dowel that would be going in the hole you drilled. See you on the next one.

With dry wood you need a much wider handle and pull it out periodically to keep the hole clean. You probably needed to drill a small pilot hole first. Out of the box tools are usually not sharp enough.

@RaindanceBushcraft

Ай бұрын

Yeah, I really didn’t know what I was doing. I really need to try it again.

Get yourself a set of crocksticks that can be used to make that extremely sharp. The triangular style are of course your best choice and only pull them into the cutting edge inside the spiral not the outside at first and pay attention to the existing angles. As I've said when it gets difficult to turn back up a bit then proceed further. You may find this helpful sugar bear.

@RaindanceBushcraft

10 ай бұрын

I’ll give them a going-over for sure. Crock sticks. Noted. I’ll go look for them.

I had high hopes as well. You may have saved me 30 bucks and for that I thank you. Don't give up, keep searching for a big honker lol

Thank you for the reviews. Just confirmed which one I'm getting. Blessings from North Carolina.

Hello, I've last seen one of these about 40 years ago when I was really little. I remember grandpa say, you are supposed to take about a quarter turn than walk it hack a bit, and then keep going like that a bit at a time. We are not machines! I bought the one with the leather pouch you have there and I love it for cutting holes in pine planks I make out in the woods with my draw knife.

I love the commentary. Lol I'm too tired for this. Lol It does blow my mind that everything was built with non electric tools at one point.

I have a couple of these in my wish list on etsy... good review sir

One more thing we used a longer tube for the eye enabling one to create a longer tenon in case you desire a severe angle in your particular connection of course drilling at the desired angle as well those we of course used a longer four fluted ivy classic auger to keep your knuckles away from your work.

Just an observation....while the lack of sharpness can certainly be a factor, you may also consider the fact that the bigger the diameter of auger, the more force is required to turn it as it goes into the wood deeper.

@RaindanceBushcraft

Жыл бұрын

Yeah, that’s true for sure. I need to spend more time playing around with these bits.

@randyschweiss847

Жыл бұрын

@@RaindanceBushcraft I actually just ordered two of them which are scheduled for delivery today. One as a last minute Christmas gift for my son who enjoys hiking and the outdoors as well as doing things outdoors. And one for myself. I figure I can make some pretty epic deer blinds.

1st time I have seen these used.. interesting...I can find some use 4 these! Thanx 4 the review!

I've always wanted to get one thanks for the review

Went thru this yesterday. Mine looks exactly like the 2nd welded one. Wouldn't bite past the screw. Wood was beech and dry. Am going to find geeener wood. Trying to make rocket-type stove. The luxury of finding the perfect log to use doesn't exist on the forest floor. I have 1 acre of old growth beech, maple and oak. Gonna go sharpen mine. Wish me luck.

@RaindanceBushcraft

7 ай бұрын

Yeah, I wanted to do the exact same thing, which is why I was drilling into the centre of the log. Definitely going to try with greener wood next time.

Thanks for the review Jes, you sold me on my Dewalt 20V...lol

Thanks for the review.

Glad you didn't eat any beans before you started on that first log.

Thanks for this. Making a small log cabin for my daughter in the woods and want to use pegs to hold it together. Been looking at these for boring peg holes into the logs.

@RaindanceBushcraft

10 ай бұрын

I think they’ll work better if you’re using green wood. Also, the kind with the tapered edge in the eye is designed so you can create pegs sized for the hole.

@krisgrier4449

10 ай бұрын

@@RaindanceBushcraft Thanks, yes, handy for making the pegs. Some of the wood is well seasoned but it is softwood so I think they will be ok. Just ordered an auger 5 minutes ago so will find out how it goes when I've collected enough logs to start building. I'm interested in making furniture too so hopefully I get good use. Thanks for the advice and replying. Good man. Subscribed..👍

I bought a 1 inch auger on amazon kind of like the one you bought but the profile of the cutting edge is actually like a double spade bit (4 cutting edges). And guess what? I have not had the opportunity to use it yet :( AS for the Auger you can't return, why not try and reprofile the edge and give it another go? There's got to be a way to file or grind it to improve it's cutting edge. At this point, what's the harm? Beats using it as a door stopper.

Sweetheart don't chock up on your T handle move your hands out to the ends of the stick for more leverage move your hands apart to the ends and in a (SHTF) sinario drill the holes before cutting the piece away from the tree 🎄!!! As it will hold it firmly for you so you can drill without using your feet as a clamp!!! Also cover your screw pilot with tape and sharpen your auger with really fine Emory cloth or a really fine wet stone skinny enough to do the job. Preferably 400 grit or finer maby 600 grit to make it razor sharp so you don't have to work so hard sugar bear 🐻!!! The reason for the tape to protect the pilot screw during sharpening.

It helps to back the auger off and remove the wood when it gets difficult to turn.

I have a couple of them, 1" and 3/4 " they do a good enough job with green wood, and I used one of them today to bore out the broken shaft of a spade, which was hardened ash. I guess it is the luck of the draw with these things, some are good some are not.

1st. a little physics will help. once u get it started with the handle in the center use a longer stronger{hickory if pos.}piece move ur wood out so the wood is almost flush{on 1 end long on the other}, do not try and hold the wood with ur feet it takes ur balance and leverage. Find 2 stumps or rocks firmly planted with ur log on its side and ur props short enough to turn ur handle. Start with a pine log.

@RaindanceBushcraft

Жыл бұрын

I see what you’re saying about the handle. I’ll try that to start with. Thanks!

TY 4 warming me! Waiting for Amazon's cheapest to arrive! Will return right away if it fails

1 1/2 inches of drill bit takes some ooomph, which you didn't have enough of . It is designed I think more for green wood also. Try taking the drill out every few turns to help with friction in the hole, also a little soap on the auger will help it go through easier

@RaindanceBushcraft

Жыл бұрын

I like that soap idea. I'll have to try it.

@williamburdon6993

Жыл бұрын

@@RaindanceBushcraft My dad always used a bar of soap, I know it works great, Liquid soap I have no idea. Never tried it.

@RaindanceBushcraft

Жыл бұрын

@@williamburdon6993 the bar sounds like the better idea.

@stepanbandera5206

5 ай бұрын

Use Ballistol or even KY.😂

Yellow birch - one of the hardest to drill types of wood found in North America ... used to make the yoke for oxen because it is considered unbreakable lol .

Don’t turn it at the center. Move your hands out to the ends of the stick. That’s how you get more leverage.

@RaindanceBushcraft

Жыл бұрын

Yeah, I did a lot wrong. I'm going to do another vid this summer, I hope.

This is my first time to your channel. You seem like a nice likeable guy. Thanks for the video. Keep up the great work. Cheers.

@RaindanceBushcraft

Жыл бұрын

Thanks for watching!

I can see the taper as just enabling a tight fit. If you have a piece of wood that is about the right size (but is not uniform in thickness ... i.e. gets thicker along its length), then stick the thin side in first and shove it in there real good. Hopefully the thinner part at the right diameter will hold well because of the taper ...

@RaindanceBushcraft

9 ай бұрын

Yeah, that could work for sure.

Видишь ли друг, первая проблемма большого сверла в том что оно большое и захватывает большое количество волокон идущих вдоль сверления. Резец просто не в состоянии разрезать эти безконечные волокна и застревает. Меньшее сверло захватывает меньше волокон поэтому идет легче. А при сверлении сбоку ты проходишь перпендикулярно волокнам, поэтому так сверлить легче. В основном такой бур нужен именно для перпендикулярного реза при постройке мебели, жилища и тому подобных вещей, когда практически всегда будет именно перпендикулярное волокнам сверление. Спасибо за видео. Привет из Украины!

They both look sub par hopefully you spent accordingly???? The black 🖤 1&1/2" one is useless it doesn't form the tenon and of course it arrived broken!!! The 1" just might break off the eye 👁‍🗨 while hammering it on the end of a branch 🌿 or sapling during tenon formation!!! Hopefully no more than $10.00 for both!!! Just curious why you opted for such long ones???? You may want to check out the new 1&1/2" version from Amazon I think made by (and I'm probably spelling this wrong) wylon or Waylon??? Anyway there $44.00+ but look beefy enough which I will order Wednesday 10-26-23 along with the 5/8" version to pin the 1&1/2" tenon so it won't back out. Just offering a little Intel sweetheart!!!

6:16 "This seems a lot harder than it needs to be." 🤣 "I drilled a hole! (Now what?)" lmao

Great video! Very cool! LOVE IT! FUN TO WATCH! WE LEARN MORE FROM MISTAKES! GREAT COMMENTS BELOW, GREAT GREAT GREAT!

Awesome video ❤️👍

Amazon is the Wild West of shopping. There’s other companies that definitely back their product. Thanks for the heads up.

Interesting video, I am still wondering if I should get one. The tests are made trying to drill the end grain of the log which is very hard and the bit loose its bite very fast. Normally you will drill along the grain on the sides of the log. This will be much closer to the real use of this tool.

@RaindanceBushcraft

10 ай бұрын

Aside from the one that arrived with a chip out of it, I’d say the tools behave better than the did for me. I really didn’t know what I was doing.

To be fair, I can whittle most wood, but anything sun or kiln dried is like rock mate.

@stepanbandera5206

5 ай бұрын

That's exactly what my ex said!

Good effort.

Thanks!

Made me wince when watching you using a hatchet while wearing sandals. I tuned out.

I'm pretty sure the auger is supposed to be used on green wood for the mortise, and the eye on dry wood for the tenon. The green wood mortise will shrink onto the dry wood tenon and grab it tightly.

@RaindanceBushcraft

Жыл бұрын

I really knew nothing when I made that video.

@stepanbandera5206

5 ай бұрын

​​@@RaindanceBushcraftThat's what SHE said!😂

You need to have your hands at the ends of the handle and your right about the drill being better against the grain

I would use that on soft wood, not on birch? Spruces and stuff, I have braces and bits and I can go thru a 2x4 no problem, with minimal effort

2:57 that is to get the proper size dowel that fits the whole the other end make in order to build structure without needing nails/screws!!!

@RaindanceBushcraft

Жыл бұрын

Yeah, I really didn't know anything when I shot that video. Ive been learning more since. I'll have to do a new vid pretty soon, I think...

Try it on a tree trunk that is in the ground

I bought two scotch eyes, the tap screw is too small, and with a bad shoulder they are a no go. I’ll try a carpenter’s brace and bit next.

@RaindanceBushcraft

Жыл бұрын

I have a couple of carpenters' braces. Awesome tool; I love them

I love videos with 100% honesty, especially when the products don't work well or work out! I have been looking at these for quite awhile also. So I very mush appreciate your video. Your honesty and review on AFFORDABLE gets a subscription from me, keep the bushcraft AFFORDABLE Chinese products coming. Also if you do a video on sharpening the auger/s and then a retest on their performance with seasoned and unseasoned wood. Even on a huge log that is not going to move around as you drill? That would be amazing. Cheers

What might help a little is you have a lever but your not using the mechanical advantage that the lever provides- hands in the middle. But that might not make any difference given the sharpness etc you point out. Longer lever might help too. Thanks though cool and good review

Its all about the work piece not being held tight, and your stick aint big enough. You cant even use a power drill press without work holding if skme kind. a vice in a shop but ive found a rstchet strap to a larger heavier object can work great taking up little space or weight. Im surprised you got as fsr as you did honestly. So try them on the side of a log big enough you cant move it with a longer stick and or ratchet strap a small log to a rock or log or tree and your off to the races.

It would probably be easier to drill a smaller pilot hole first and then drill a big hole.

What would you use this for in the woods?

@MiscMitz

Жыл бұрын

Making shelters and furniture and stuff. Bushcrafting...

@lazymanoutdoors9293

Жыл бұрын

The one that had the welded part, looks like a settlers wrench, one side of it will be sharp. You can use that to make pegs to go through two holes you have made to form a joint when making items. Much better to cut into green wood than seasoned wood/dry wood. They are an absolute b**ch to use in hard dry wood when your using inch plus diameter. Thanks for the vid, appreciate your time and effort 👍

@RaindanceBushcraft

Жыл бұрын

Could make a rough camp stool or for holes and pegs for a semi-permanent shelter. I think they're used more in log cabin building.

Thanks for reviewing two different models and showing the trials of using new tools. It's worth sharpening for better results. Better quality models, would eventually need sharpening anyway. Today, I got the same 1" model you have. I'll fiddle around with it and see.

Should have started with a smaller one for a pilot hole.

Interesting

Ну ты даёшь мужик )

Make yourself a longer handle for more leverage and spread your arms ourt.

I built a 420m post and rail fence using a brace and bit by hand abd did not struggle anywhere as much as you are!!! get better equipment!!!

Bonjour, Avez-vous trouvé une tarière de meilleure qualité depuis cette démonstration? Avez-vous regardé sur Etsy?

@RaindanceBushcraft

Жыл бұрын

Pas encore. Pas de temps pour l’instant

Like hard work man just to make a Swiss torch

Is there a company that makes 'quality' versions of these?

Well I’m also disappointed because I just ordered one. 🤷🏻‍♂️ might just keep my Milwaukee drill and solar charger.

First time viewer. First, thanks for identifing and comparing the Scotch against the Bushcraft. While I many never have to build a log cabin, knowledge in and of itself is valuable. A bit of constructive criticism. Safety. We live in the mondern world and get careless when we don't acknowledge danger or over confident. Chopping anything while wearing slippers or any protective gear is a accident waiting to happen. Even a wood block in front of your legs to catch a missing chop would be an improvement. I could go on, but i think the other commenters have weighed in. I truly appreciate your video and view it as a learning tool. But please include some level of safety in your videos going forward. Protective goggles, gloves, steel toe shoes or even hocky shin guards, lol.

Tools a pain in the ass. Everyone else makes it look easy

Is that’s a granfors Bruks hatchet?

@RaindanceBushcraft

Жыл бұрын

It’s the old Wetterlings Buddy hatchet. Gransfors makes one in the same size. The Wetterlings one has a thicker head, though.

One thing is for sure it was an honest test and the tool is not what they paint it to be. Which shouldn't surprise anyone. Great job!

@stepanbandera5206

5 ай бұрын

The operator was the only failed "tool" I saw. 😂

I only wished I would have watched this BEFORE I purchased the 1” same one in the video, hopefully it works for me

@ABonRMS

Жыл бұрын

Ditto, cut firewood yesterday for next year, I’ll try my 1” on it. Plus figure a way to hold the log to be held on place. Wish me luck

@PhantomofthePrairie

Жыл бұрын

@@ABonRMS good luck, let me know how it works.

use the ends of the handles

It appears the chip in the leading Edge is the problem or at least part of the problem. If you can’t return it perhaps it could be sharpened. What ya got to loose, thanks for the review. I hope you have more luck with the 1” and fresh cut logs

Should probably fasten the material your working on to something solid like a stump maybe? Increase the handle length perhaps 🤔 I don’t know could ya bring the work to your waist I’m thinking. I don’t know why people do their job on the ground, seems so primitive. I’m no auger expert but I know you need downwards force along with steady and straight accuracy to drill just about anything really

@jamesgraves1639

11 ай бұрын

Increasing the handle length doesn't do any good if he continues to choke up on it!

Sweetheart why are you coring that round to begin with??? And if you wish to clamp it still run your ATV tire up on it angled up so you can have room for your knuckles while drilling sweetie.

Also wear gloves unless you're already thoroughly calist to resist the blisters that may rear there ugly heads. And don't just keep twisting in one direction ocilate when it gets difficult and continue.

Nice test. Love the safety shoes! JK.

Lo has hecho difícil porque agarras el palo mal, debes agarrarlo de las puntas

I like your review Jes👍👍- I have never been a fan of that type Auger.

The drilling is the relatively easy part however the most difficult part is making the doweled end when trying to remove the stick from the eye which is near impossible. The concept is great but reality is this tool takes way too much effort to be useful - and you need to carry decent gloves or you will tear your hands up.

@RaindanceBushcraft

9 ай бұрын

Good to know. I saw a vid recently while doing more research and the guys was definitely having trouble getting the dowel out.

Use on sides only. kinda logical.

you need to learn physics at school. Have you heard anything about the lever effect?

Holding it is a big hassle

For the love of god 😵‍💫that was painful to watch the hole way through , im sure you figured it out by now , i like mine

I bought one the most expensive ones on Amazon thinking it would be high quality. Nope, cheap junk probably from Chyna

@RaindanceBushcraft

Жыл бұрын

I'm thinking that Amazon is not the best place to find one of these. I think I'll see if I can find a single maker or small team to give my money to instead.

@ventures1

Жыл бұрын

@@RaindanceBushcraft reading all the comments I was hoping you, or someone else would have recommended a high quality auger. I bought one on Amazon and am happy with the few holes I’ve drilled, but would like to test the one I have with a high quality one. I’m sure my 14$ auger wouldn’t be ‘top quality’.

Well that does it for me, not going to bother with that tool.

I hate to be the one to break it to you but there is nothing wrong with the tools. You need to start working out everyday and eating right. Build some muscle man and a good pair of work boots will help as well.

Hard to watch....why are you turning with the center of the handle. Use the outside of the handle, it's called leverage 😅

you'd better go lay on the hammock man, get some well deserved relaxation

@robertbihn3005

6 ай бұрын

you got thumbs up for good try !

Does not seem like it’s very efficient. 🤷🏻‍♂️🤷🏻‍♂️🤷🏻‍♂️

@RaindanceBushcraft

9 ай бұрын

My utter incompetence at the time was a factor for sure.

God bless you, but you disappointed yourself. Not making use of leverage is a bit sad.

A REAL hand powerd Auger is different than a drilling Auger. It has more to do with the cutting force being easier than lets say the sharpness. Look at the geometry of a real hand one. its going to be a much slower speed. These idiots who make adapters to drill aurgers are just wasting your money, time and energy.

Perhaps an electric drill would do the job quicker

@stepanbandera5206

5 ай бұрын

Yup, kwiker, just like my electric woodstove 🥴👍.

Log is too dry? Like a monkey f’n a football….

Bushcraft? More like bush league.

I appreciate the video, but you're in shorts with a hatchet, and I didn't see a tourniquet. Get one and learn to use it. You never know when you could hit your leg and cause a self inflicted injury. Otherwise, fairly informative. Keep at it!

Learn to sharpen the tool! Learn about leverage!

Bardzo duża nie wiedza.

Your drill is just too large.

Doesn’t even know how to use it 🤦‍♂️ don’t drill the end of a log, u go in the side and the layers in the rings will hold the bit. Know how to use a tool before reviewing it when u don’t know how it works.

I'm not impressed