Watch my video on How to make Automatic Spot Welding Machine using a Microwave Oven transformer kzread.info/dash/bejne/qqKEq9WrqLnVqrA.html

@kylewatson952

2 жыл бұрын

@16:16 hello I whould like to make this but I have one question for you sw on the joystick I can see it connects to a pin on the board my question is what pin is it connected to? I believe it is the resume pin if I can see it right thank you fro making this video.

@Zanthra434

9 ай бұрын

what's the amperage limit/requirement for the power supply? i got a 12v 3a power supply and i cant find any documentation on amperage

Great video. I bought that shield and drivers ages ago but had no idea how to use them. You've shown me how!

I'm working on interfacing my collection of stepper motors with arduino to a commercial printing top this video has helped alot. Thank you

Amazing video explaining everything on the shield, it helped me a lot on my project, thanks for the info!!!!

a very informative and clear-to-understand tutorial - congrats!

Got it running in the end. Syntax ! Thank you. Vref is measured from the potentiometer wiper (which is live) and ground. I am hoping to run without the heatsink which is precariously close to other live components, hence a risk of a short circuit.

exactly what I needed! thank you!!!

Very informative and helpful

Thanks a lot for good explenation and showing what all connections is. I hope I can use this boatd for a 2 wheel balancing robot. Have a nice weekend. 🇧🇻😉

helpful tutorial. I am getting idea of generating pulses to stepper driver

great video bhai. Nicely explained.

Thanks for the detailed explanation, very useful! You could make it a bit shorter by skipping to read the pin names without explanation if you explain each pin anyway. Its redundant information and clearly visible in the video which everyone can stop and rewind if things are too fast.

Great video, thanks. Are you able to tell me how I can use NEMA34s with the Shield? I got separate drivers for the steppers, do I connect the motor coils to the 4 pins of the Shield or to the DM860y driver? What connects to the X and Y Direction and X and Y Step for example? Will try a 2 axis plotter/engraver for starters. Any suggestions would be greatly helpful as I'm completely new to these things. Thanks!

great job 👌👌

very good explanation, thx so much

For anyone having issue setting vref. Setup the driver in a breadboard and NOT on the cnc shield. Something about the knock offs being slightly different. My vref was always 0v when trying to adjust on the shield.

@BobbyNFC

Жыл бұрын

I had the same problem, but when I applied voltage to the Arduino from my laptop through the USB cable Vref showed up on the pot and I was then able to adjust its voltage.

A useful video. I like it

Hey, thanks for a very, very good guide! 👍 I'm currenty working with a machine (can't say manufacturer), but it use both a combination of PLC and robotics. Wanted to learn more about ladder PLC, and do some experiments myself. Most "guides" I have found are not as comprehensive your guide. I have a 12volt power supply, but it's limit will be 12V, 1.0Ampere and a maximum of 12watts. So I'll be getting a laboratory power supply. As of now - no stepper motor, but no fear, we have a bunch of them at work.. Also, I was thinking.. If planning on building a "robot", what if I would like to use a real type of joystick? Say with six axis? I was looking at something like the Amastone. It has XYZ axis (selectable), emergency stop and a dead man's grip for additional protection. But, what if using a gaming joystick, with say an hall effect sensor? Need to re-route it via an interface/shield to the Arduino, is my initial thought, or just hack it??

Thank You so much for Sharing from Your knowledge ... Thank You ...

@ElectroniClinic

3 жыл бұрын

So nice of you

really nice video!!!

Nicely explained

Nice Bhaiya Keep It

Thank you!

Great communication

Hi, Great video. Do you know which pins I connect to on the shield when installing an external reset button? Thanks.

Great another amazing video. Good work!

@ElectroniClinic

4 жыл бұрын

Glad you enjoyed it!

@chimpofm

4 жыл бұрын

This is perfect for my chemicle dispenser. I would love to see you make a automated cocktale drink mixer. Mixing juices at different recipes

Great video.. Thanks At 11:00 you mention pin #8 is not connected. On my board, it is connected to EN right above X-Step

Welcome to Bob Ross Electronic Clinic! Let´s gonna connect some happy little budies here...

This is brilliant, thank you. The only thing I'm confused by: it looks as though you have the GND from the joystick connected to Z+ pin of CNC Shield in the video rather than to the GND pin (as it should be and as you instruct) - that pin is next to the 5V pin on my CNC shield. Is that just an error in the footage?

Thank you for the video! But... the jumper (14:15) supplies voltage all the time. This leads to overheating of the drivers. It is better to put a jumper on a free pin and apply -0- only when the engine is turned on and immediately turn it off if the engine stops working.

How do I know or calculate the appropriate power supply requirements? It’s been suggested that I use a 12v 100W PS, but I’m curious to see if I can use either 12v @ 76W or if I need to access 24v @ 144W? There is also an option to change the 24v down to 20v to get 100W.

You have done a great service to the students who use this shield first time. Sir, may I know if the shield enable pins are not shorted what will be the problem?

Great job

Thanks.

excellent bro

Nice job

Great video. Where do I connect the 12 volt spindle motor. My shield uses a 24 volt power supply.

helpful video

Why my gantry not moving continuously but only single times for few unfix distance after sending moving command from Ugs and then in few attempts it gets disconnected until I reset the arduino, or software? I think it's because of EM interference create by motor but not sure since it showed be immune to these EM noise as it's made for these purpose.

OMG finaly! that jumper detail!i dont get why it needs the jumper but it works!

So helpful !!!

Great video. Im a bit confused with the vref formula. Anyone can help me? My stepper motor rated current/phase is 2.0A Thanks

Thank you so much for this tutorial! Very helpful. Do you know how can I effectively short the ms1, ms2, and ms3 pins? Basically I'm hoping to use 1/16th micro stepping all the time. Is there any tool / caps that could help? With the limited space provided on the shield, I couldn't find an elegant way to short them, unless I manually solder those three header pins... Any help will be greatly appreciated!

@ElectroniClinic

3 жыл бұрын

you can use jumper caps

@daveapplemotors

Жыл бұрын

@@ElectroniClinic What about setting 5,6,7,and 8 high in the program? Not sure if those are right ones that go to the steps pins, whole, half, quarter...

Hey I have a question, what pins are A.STEP/DIR connected to on the arduino board?

thank you!

Bhagwan Se Dua 🤲 Karunga Ki जल्दी mere Bhaijan ka 100K Subscribers Ho jaay Aur fir 1M 🙂

I had a problem not being able to adjust Vref with the A4988 driver located correctly on the shield, which was attached correctly onto the Arduino, even after following all the instructions presented by the video faithfully. But then, when I applied voltage to the Arduino from my laptop through the USB cable, the Vref voltage showed up on the A4988's Vref pot and I was then able to adjust its voltage. I hope that might be of help to those that might be having the same problem.

Do I need a power supply to the uno and cnc shield when I use the router I usually just run 24v on the shield and the usb seems to power the uno is this ok to do

Very good ticher

my spindle was not moving, jumper tip resolved it. bunch of thanks

i want to know code vs a4988 anh dc step with fuction on off 5 round, can you help me

An excellent narration on CNC V3 Shield. Thanks a lot. How to connect a SG90 Servo to CNC V3 Shield ? Please help me.

what about rotation robotics like robotic arm which driver we should use ?

The KZread was ok - but i didn't see any relationship with a hybrid stepper motor - the one shown was just a normal stepper motor

nice

Hi, I try to setup the joystick but error message apiered on the line jostick () ; ( your line 25 ) Can youhelp me ?

Will you not connect another stepper motor with the shield and modify the. Code in Arduino?

urgent... please help can I use CNC shield for control Nema 23 stepper motors using TB6600 stepper drivers.

Nice job ! Can you please help me how is possible to controll 2 stepper motor ?

Hi I have a quick question. Is there anyway to power the Arduino board without it always being connected to computer? I have a 12V supply connected to the CNC shield, but it only runs if I also have a 5V usb connection to the Arduino board. Any way to tie in a 5V from the 12V supply, so I can make my product mobile (not confined next to a computer)

@mrsaizo0000

Жыл бұрын

Several options there. 1. Get a small powersupply you can carry with you. 2. Use a LiPo battery pack. 3. Get an USB2Go connector, connect it to the phone you use, get ArduinoDroid or similar to control/edit the code.

Good tutorial, I noticed you did not cover any explanation orientation or format after soldering your stepper motor wires before joining on the 4 male hitters on the cnc sheild. Does it not matter which order these wires should be connected?

@ElectroniClinic

4 жыл бұрын

i have already explained this in my previous videos on the stepper motors.

@danaidouglas

4 жыл бұрын

@@ElectroniClinic thanks, I looked at both your videos for stepper motors and could not find the answer to my question, though I did pick up a few things. Thank you.

Great video. Based on what did yoy adjust the potentiometer?

I make CNC project but my case is stepper motor not working programming is ok and connect software but when command it not working

Hello, i have a question, what would be the purpose of shorting @ 9:57 does it enable us to control those motor? Sorry if its a stupid question. I ask because I am currently beginning to research how to control my 3 stepper motor without using GRBL and I'm kind of confused.

@mrsaizo0000

Жыл бұрын

It's to enable the control of the stepper motors, yes. However, I found having a toggle switch soldered on to female connectors was just as easy. Same goes for emergency stop - get a real switch and modify it for your own purpose.

In other tutorials, their formula is VRef = (Current)*(8)*(resistance of the current sensing resistor). In my case, it's either VRef = 1.7/2 or VRef = 1.7*8*0.1; both yield different values. How can I tell which formula to use?

@nadineh9879

2 жыл бұрын

it depends on the driver you use, the first formula is usually for A4988 and the second for DRV8825, you can find the specific formula in the datasheet of the driver you use

Sir, Very informative video. I am a hobbyist. I have used 'Arduino UNO, CNC Shield 3 and A4988". Before switching 'ON' 12V to "Nema 17 PM " stepper motor following steps were done as shown in the video: 1. Set voltage on "A4988 " board. 2. Short 'Enable' pins. 3. Attach 4 wires of stepper motor. Can I go ahead please? Thanks,

Nivel vídeo. I Made it work, how can i control the speed?

Luv the work u r doing. I want monitor the capacity of my 14.6v valence batteries shud I use amp connector to rs485 to logic level converter to 4 module relay to arduino. And please how to connect?

Great video though I noticed that you used the vref calculation for the DRV8825 driver and not the one for the A4988 which is what this video is about.

@brahmadevs

3 жыл бұрын

can the exact same methodology be used for DRV8825 driver because i noticed that the pins 1A, 2A, 1B, 2B are arranged differently in the DRV8825 than the A4988? The order in A4988 is 1B 1A 2A 2B and the order written in DRV 8825 is 2A 1A 1B 2B.

@zk_6312

3 жыл бұрын

@@brahmadevs The method is the same, but the formula for vref is different. The formula for vref is on the datasheet for the driver.

@pofigschool

Жыл бұрын

Yes you are right. For example for 17HS4401: Vref = 1,7 / 2,5 = 0,68V (14:47)

Hello sir, could you please make tutorial about how to control 4 stepper motor using this same exact setup? Thanks

@manford75

2 жыл бұрын

Have any luck with that? Trying to get the same thing going.

hey loved it!! but how to reduce speed m a noob please help!!!

How to disable a specific stepper motor on the shield?

whats the maximum RPM we can achieve using this setup. I need around 2000RPM please suggest setup

hey man. how are you? how can i duplicate the code of joysitck for 3 stepper motors ? Thank you

hold pin what it for?

How to use hold / resume as button.. can you please help guide

Hi I Have make a small project With arduino uno + cnc shield v3 + A4988 motor driver + stepper motor i have programing by computer. and it's done. but now i want programing controller with display. do you guide me please?

@ElectroniClinic

Жыл бұрын

Ya, sure.

Can 2 pin connected to the drive? The stepper motor has 2 pin only

Sir i do cnc router project sir but i face some problem the problem is how to decrease drive voltage sir

Please make a vidio servo motor manual controller

How to use joystick with 2 motors, for X and Y?

Please help! First of all, thanks for this well explained video. I have a big question, if I want to use this cnc shield but I will only use two nema steppers, but my main question is, if I need to use other digital or analogical pins for other device, is it possible? Because the cnc shield is connected on the whole arduino... thanks

@ElectroniClinic

3 жыл бұрын

yes.you can use. For this reason i designed my own stepper motor controller. i will upload the video on 1st Feb. in that video i have explained how to use any number of stepper motors and how to use io pins to control them.

@phongnguyen-ow8zq

3 жыл бұрын

@@ElectroniClinic help link

why not any body tell 775 dc spindle motor conection to shield detail ??

Does anybody have the code for controlling 2 motors direction with one joystick??? I have the same hardware as the video, the but no matter what I try I can only get one motor to listen to the joystick and the other just free spins if power is on :( help would be greatly appreciated.

@ElectroniClinic

3 жыл бұрын

this joystick has the button as well. use this button to select between two motors.

A4988 drive is suitable for 10 kg bipolar stepper motor.

error occurred bro not in the code only in the uploading process.what to do for that bro?

Hi. My motors dont move but connection is ok. I cant find anyone saying I must enable the ground in the shield.

@ElectroniClinic

Жыл бұрын

My video helped you or not?

@joseguevara184

Жыл бұрын

@@ElectroniClinic Hi, thanks for taking the time to answer. I already made them work but in tests the motors produce much noise and vibration. Some say use full steps and others that reduce it to 1/8 or so but also say it is bad for the motors? Who to believe? I am using Nema 17 2 amperes motors at 1.25 voltage. Thanks.

What about spindle motor connection sir....

hi, can we make controlling 3 stepper motor with 2 joystick with this diagram?

@ElectroniClinic

2 жыл бұрын

of course you can control, but you will need to modify the code.

All was going well BUT, you don't show where to measure the V Ref, and you seem to give the formula for the DVR 8825. So, ultimately, interesting but suspect.

Can you please create guidance on end stop limit switch on this cnc shield

@petermuller608

3 жыл бұрын

Wire them in NC mode. The grbl wiki has a great explanation on how to do this

I want to drive a stepper motor on the seat which can move forward and backward and with nodemcu if you can help please

@ElectroniClinic

2 жыл бұрын

why a stepper for this? you can use a DC geared motor and control it via bluetooth.

@ElectroniClinic

2 жыл бұрын

And u use limit switches with the motor then you can also define the starting and end position. I dont know which type of seat you want to control? is it for kids or adults? its a car's seat?

@ElectroniClinic

2 жыл бұрын

you also need to look at linear actuators. I have a video on this.

@mrsaizo0000

Жыл бұрын

How much travel do you need? Weight limit? I agree with a linear actuator.

Freand I need how to cunect breakout board to servo driver wiring and cuntrol

Please can you make a video explain how to do grbl work with A4988

@petermuller608

3 жыл бұрын

Just put the A4988 driver carrier into the cnc shield, put the cnc shield one the Arduino 328p and flash grbl. This is literally the most basic setup ;)

没看懂，编程没看懂，摇杆部分是怎么接线的？

how to 2 axis?

can i use this cnc shild for diy 3d printer

@ElectroniClinic

Жыл бұрын

Of course you can.

Its working great for me but would like to control 2 step motors how to do it ?

@charmingali34

3 жыл бұрын

Hello, I am also figuring out to control 3 stepper motors. If you come across any help or supporting materials please share the link. Many thanks

@petermuller608

3 жыл бұрын

Send step / direction to the appropriate pins

@charmingali34

3 жыл бұрын

@@petermuller608 thankyou I was able to control 3 steppers but they all run simultaneously at same speed. However, I want to make them run at various speeds for each one of the stepper motor. Any lead on that, please?

@petermuller608

3 жыл бұрын

@@charmingali34 are you sending step pulses at different speed to your three motors? The step frequency is directly related to the motor's speed

@charmingali34

3 жыл бұрын

@@petermuller608 I am able to send step pulses at 3 different speed but for that I have to change the speed everytime. So the option is using Arduino Serial Monitor I can give my values but Serial Monitor is very basic and not a friendly GUI. So, I build a GUI on processing and sending the values from Processing 3.0 to Arduino. But the problem being faced is I can only send one value at a time from Processing 3.0 to Arduino which will run the 3 motors at that particular speed. However, I want to run all 3 motors at 3 different speeds simultaneously. An advance thankyou for your time on my query.

Can we connect i2c keypad and LCD to CNC shield? Keypad used to input the steps/revolutions to stepper motor.

@ElectroniClinic

3 жыл бұрын

i did the same thing using android app instead of using a simple keypad watch my video on android controlled stepper motor

Connected and done as described without joystick part, but motor is not rotating, instead it is getting current at getting fixed(jammed), Any solution???????

@ElectroniClinic

4 жыл бұрын

check your stepper motor wiring.

@MrPpbis

4 жыл бұрын

@@ElectroniClinic one pair with zero resistance to one pair of + and - , its ok ?