Thanks Zac for assessing our machine! Your welds are excellent! We anticipate that our welding machine will be helpful to you .😊

@jevgeni1094

Ай бұрын

хочу купить этот сварочный аппарат, но очень мало информации, читал на сайте который похож на рекламную брошюру. не могли бы Вы написать более подробно где производят кому принадлежит бренд и почему не во всей европе его можно купить

Experience tig welder for sure reviewing a welder without reading the manual shows you how some what intuitive the AR Captain is to operate

People think Lincoln and Miller and Hobart are the best while Arc Captain are rising up to take that Spot all them other companies make all the welders very expensive while Arc Captain makes it super affordable Can't wait to see if they make a engine drive welder if they do then Lincoln, Miller, Hobart they are done for good. also my Arc Captain welder doesn't have a issue with 6010 I use 5/32 but I need to use 140 amps to use that rod I want to get 1/8 or 3/32 maybe it will run a lot better at low amps Cant wait to try Blue demon also 2T is when you press down you need to hold it 4T is press down let go and when you need to stop tap the trigger again to shut it down These welder DO a HELL of a lot better with 240 Volt all welders do

@arccaptain-weld

11 ай бұрын

This is exactly what we are doing, thank you for your praise!

@ia6980

8 ай бұрын

no it wont take their spot, at least not in near future, i own this arc200, it is not a good welder. IT does not produce consistent results, especially when you perform vertical welds, it was horrible, lot of bird poop, with some good welds in between using same technique and same rods.

20:12 10/10 dad sneeze right there

I’ve never stick welded with 110 and ever expected to run a good bead lol

@DarlingtonFarm

Ай бұрын

my little miller maxstar actually does ok for 3/32 7018 off a 20 amp breaker

I had no problem in keeping mine lit, 7018 should be ran at around 115-120 on this one that's 3/32. 1/8th 7018 around 195 amps for a decent weld. But when it comes to vertical weld, puddle is not consistent, therefore this welder is only for backyard use, where bird poop wont be an issue

Great machine I prefer most because of the AC/DC-function. Now I have a HBM200TIG without pulse. I miss this pulse though. Over here in Holland a 6010 rod can be run more easily because we have standard 230V and reach the higher amps. It's supurb on 110V and 230V what is the setup of this machine. Very learnsome Vid and what a great introduction. Greetz from Holland, Marcel Knippers.

Please do a vertical STICK weld, perform 1/8th 7018, 3/32 7018, and 6010/11 1/8th and 3/32, please show if youll be able to get good vertical welds going up and have no issues? mine was a true struggle with vertical welds going up the line. Had much better success in regular when its on the table.

Very good review! Definitely read the product manual next time😂 save the headache

What a Brand ist your welding Helmet?

Lol brother trying to figure out how a knob works for menu selection/value adjustment is both hilarious and frustrating.

@andrewford80

Ай бұрын

That was a tough watch.

I really wanted to like this welder, its small, light, compact, but man, what an inconsistent results, finally had okay weld on one vertical side, performed same technique on the other side and it failed miserably with lot of bird poop using same amps and same rods. I'm not impressed with this machine. Anti-stick option is useless, and arc force found to be useless and did not noticed any results. Rods still do stick and lots of bird poop with this welder. I only used STICK on this one.