Great video....I would have struggled to do this without your guidance.....thank you very much. I did struggle with the bi-wiring of my L&R speakers. When I got my graphs my main speakers were dropping off at a high frequency, but once I’d figure out that I had to add them as part of the surround everything was perfect. Excellent work.

Thank you very much for this great instruction video for setting up the AVR 850! I bought one and had a lots of trouble in doing the measuring steps. After viewing and understanding the way you did it, I had to give it another run. Thanks a lot!

@PursuitPerfectSystem

6 жыл бұрын

Andreas Suck your welcome mate thanks

Thanks for this video, it's very much appreciated!

Excellent video helped me so much made me understand Dirac more thank you, any chance you can do one for Arcam Dirac Version 2 please??

@jenniferandfreddiemendoza7651

4 жыл бұрын

Jin P it’s about the same as shown on the video. It just looks a little bit different.

Hello yes you want to point the Mic to the ceiling for multi channel measurements. I used a little bit of video I filmed for setting up Dirac Live for stereo only. Sorry about that and well spotted

super helpful, thank you

@PursuitPerfectSystem

6 ай бұрын

Bare in mind some of this is out of date now

I'm curious how the Arcam 850/30+ would compare with the new Nad T 778? I hear the 778 has a Sabre chip like the 30. But in terms of amplification, I assume the 850 and up from Arcam might be better?

Can you do another video with the current dirac live? Alot has changed. Esp speaker levels

Hi first of all great video, I’m just going through this using a umik mic but if I put the gain down to 0 I can’t get the mic to pickup any sound the only way I can is by having the gain set to maximum I’m using the 90 degree umik file is this ok or normal? Many thanks Nick

Hello are there a video coming on dirac target curves ..? Best regards

Have the Target curve video uploaded and what it is?

If I have an undated firmware for AVR 600 to 1.4 3D should I preform the factory reset as advised at the first of this video?

Thank-you so much for the guide. I would not be able to do the calibration by myself without this!!!! Quick question: is Dirac 2.0 much better than 1.0? Worth the effort to calibrate everything again?

@PursuitPerfectSystem

4 жыл бұрын

yes

Hi, Thanks for the instructions which are very helpful. Just one question though. After linking the speakers and optimising to get one target curve you unlink and then roll off the bass of each speaker to suite it's frequency measurement. You say this is really for insurance so is it that the crossover you set should actually ensure the speakers are not being asked to do too much ? In other words is simply setting a sufficiently high crossover enough with no real need to go back in and roll off each speakers bass?

@rileyjesiah6284

3 жыл бұрын

i guess I am kind of randomly asking but do anybody know a good site to watch new movies online?

You also need to set the Crossover to 200Hz (max) before calibration as well

@PursuitPerfectSystem

6 жыл бұрын

richardsim7 why if your setting the speakers to large there is no crossover being used?? Are you thinking for the subwoofer?

and if can i ask, i dont have menu or setup on Arcam avr550? like u did at early start, i cant set them on large at all?

Hello Pursuit Perfect, just an amazing video and a big help, in fact Arcam video is not that detail or effective as compared to yours.I need your advise and help;Equipment I am using;Oppo 203, AVR 850, Dynaudio emit 30 front left and right, center B&W LCR 600 S3, rear definitive technology di polar SR9040and rear back def Mythos gem.Hope my speaker set up is good, Yes I have to look into center to match the left and right. Great job done and I will share your video with Arcam to learn something from you. Key part I learnt was put all the Direct measurement in one front and left speakers and then optimize, once done separate each speaker individually. Very good coherent sound all around, that is amazing. I have few question please help me;1. Measurement does not seems to be very accurate, should I measure in feet and convert to MS? each speaker?2, I like little louder sound from back, how should I keep the over all volume level of all speakers. 7.1 including back and front.3. Do you recommend anything else to make it better for movies and music?4. what Hz reading should I keep.5. I don't have any fancy place its a living roomPlease below picture to have a better understanding. I will put in another post.Thank you in advance

Hello There, I am doing my dirac live updates, firmware and new updated dirac live celebration. I am still following your instructions posted on this video. Did you do any updates or correction to this? Please let me know if I am good to go. Thanks Great video

@jenniferandfreddiemendoza7651

4 жыл бұрын

Jack Ryder I think the latest firmware for the AVR is the 1.7... as far as Dirac goes use the 2.4.1 version instead of the one that it’s on the Arcam website. Make sure you are hardwire into the router from your laptop. Don’t rely on the WIFI. But as far as doing your measurements it basically the same as the video shown.

HI Great vid. What do you think of the bundled mic that comes with the 850?

@PursuitPerfectSystem

5 жыл бұрын

sorry, no idea I haven't used it - I have only ever used a Minidsp UMIK 1

Quick question do you get the full version I’d Dirac love with the Arcam AVR 390? The only reason I ask is with the Nad M10 you get a lite version.

@PursuitPerfectSystem

4 жыл бұрын

yes you get the full version with all the Arcams :)

Great Video. What Brand are the Bumpers under the Unit?

@PursuitPerfectSystem

6 жыл бұрын

Hi Richard they are called Cera-Discs from this company www.plinth-design.com/ I helped with thought process behind them and did all the initial testing. I dont think better exists at anything like the price point. Factoring in ideally you want them under everything compared to stillpoints for example these are amazing value

Thanks! Nice video. In your opinion the input gain ist set too high?! Can you tell me why, please. The third point in the description on the right said something different.

@PursuitPerfectSystem

6 жыл бұрын

When Dirac Live first comes on the Input gain is set at +db in the red. I dont think that as right, its not like that in the other version of Dirac Live I have. I set that to 0db and work from there as 0db makes sense to me

@kigbeckovic9685

6 жыл бұрын

Pursuit Perfect System, thanks for your feedback. I think your Dirac setup guide is absolutely perfect and thank you for that. I was always set the input gain as described on the description in the right corner. The message is: 1. Always start with input gain at its HIGHEST setting, and output volume at it’s LOWEST setting. 3. Gradually move the Input gain down until the background noise level is just below the -24dB mark on the Level meters. (If the noise level remains below the -24dB, even when the input gain is set at its highest, then just leave it set there) I’m a little confused about that.

@PursuitPerfectSystem

6 жыл бұрын

Kiиg Becković! Maybe thats the best advice for using the included microphone with the arcam. Maybe the input on it is very low. To me it makes no sense to overload the input above 0db if you dont need to. To me 0db is the highest level

@kigbeckovic9685

6 жыл бұрын

Pursuit Perfect System. Hmm...but if you open Output&Levels for the first time, your Input Gain is factory set at +20. And on your video I can see clearly that the level meter is just fine about the needed -24dB, but you just set it to zero! And after that, the level meter disappear from -24dB under -36dB?! I don’t use the included microphone. I do my measurements with an miniDSP Umik-1. Sorry for asking that again and again. I just hope to understand it right.

@PursuitPerfectSystem

6 жыл бұрын

Kiиg Becković! If you feel more comfortable do it that way. I can see no logic in having a plus signal for the mic input when there is so much gain left on the output signal. I have dirac live software on another device and it doesn't auto put that at maximum. Thats come straight from dirac

Hello how did you set up the Subwoofer..? If you watch the Arcam's own KZread video they say that you should have the output volume at max in dirac live and adyust back on the volume nob on the Subwoofer manualy after the other speakers output volume. Hope you understand what i mean..:-) Or should i set subb volume to half volume back on the subb and adyust the subb in dirac live output level so they match the othet speakers instead you think..? Have you done any more video about how to calibrate and adyust the calibration messurements "Target lines" ..?

@PursuitPerfectSystem

6 жыл бұрын

It doesnt matter what you set the level on the subwoofer itself for Dirac as you set Dirac up after - however you will want to set it for what is best for your subwoofer design. Different amps on subs work differently I have found the SB13 Ultra subs from SVS work better with the volume nearly maximum - they seem to have better extension like that and that is how I set them. This might also be dictated by where you sit in the room and how much room gain you get and how much bass echo there is in your room. My Bass echo is very low due to a lot of absorption products from GIK acoustics. I do set the overall volume to maximum - 0db is maximum - above 0db makes no sense to me. Maybe you would need this extra gain in a huge room, not sure but I dont see the mileage in going over 0db for the overall level I do plan to make a target curve video - its bit of a faff get the footage I would want thats the only reason I havnt made it yet, I will try and do it soon. Let me know if you need anymore help? Thanks

@kenzo06ful

6 жыл бұрын

Pursuit Perfect System I have a room how is 6.5meter long and 3.25 meter wide and 2 meter in hight and very dead room well damped. I have also svs subwoofers..:-) dual pb2000 in my room. So what do you Think set Theme higer then half volume And do the set up in dirac live after the other speakers..? I got the Arcam avr550 Do you have any other great tipps to sett up the svs subbs Good.. :-)..?

@PursuitPerfectSystem

6 жыл бұрын

They are going to have similar amps in to the Sb13's - I read advice from SVS re having the sub level high and input gain level lower - however if you want to check for sure email SVS Technical they are very good at answering questions from customers. In terms of your room size its the same size as mine roughly - its only a small room so you dont have to worry in that regard.

What's wrong with using the calibration microphone the unit comes with vs spending another $80 on a separate microphone?

@PursuitPerfectSystem

4 жыл бұрын

nothing wrong with it, the minidsp mic is known for its accuracy and is the ideal solution for the job

Hi. I did Dirac Live (the newest version) set up with my Arcam AVR850 today but I didn't change speakers to Large, should I do calibration again? What is missing ?

@PursuitPerfectSystem

11 ай бұрын

No that was only something you had to do years sgo

@tomasz3671

11 ай бұрын

Thank you

When I play the tests for the channels the test tones play out of the wrong speakers. I have unplugged my speakers and plugged them back a few times to make absolute certain I plugged them correctly. Has anyone else experienced this? How do I correct it. Left channel is correct, center is right, right is side left, side right is center and center is right. As you can see it is all over the place. I've tried a bunch of things, any ideas?

@PursuitPerfectSystem

6 жыл бұрын

Tim Schneider no idea what is causing that do you have the latest firmware installed ??

Would you happen to know why I can't get dolby atmos through the arc HDMI connection when streaming Netflix through the TV app?

@PursuitPerfectSystem

4 жыл бұрын

I have never used arc on hdmi, really dont know sorry

@jenniferandfreddiemendoza7651

4 жыл бұрын

On the menu where it says “speaker type “ you have to assign them to Dolby Enabled speakers. It also gives you the option to let the AVR know if those ceiling speakers are in top front, middle, and rear.

Any news on the custom target curves video?

@PursuitPerfectSystem

6 жыл бұрын

June David sorry been so busy not hsd a chance to do it yet

this is the measurement I got from Dirac which is not completely accurate when you measure the room from the sweet spots

I don't understand having one curve for all the speakers (14:39 mins). Surely the orange line is now telling the sub to go up to 20 KHz and is also telling the surrounds to go down to 25 Hz (approx). I have different make sub, fronts and surrounds. I would have thought to leave each speaker as the green Dirac curve recommends as it has EQ'd them all already. Can anyone help please?

@PursuitPerfectSystem

6 жыл бұрын

It doesnt work like that, the green line is just your target curve its what Dirac will eq not what it has eq. In an ideal world the best surround system would have all the same speakers all sounding identical for an immersive sound field. In the real world thats miles from the truth thanks to the influence of the room and often the use of different speakers in different positions for convenience. By adding all the speakers together you do 2 things - you ensure you set the same target curve is set for every speaker so that they all sound as the same as possible. More importantly it allows easier visual subwoofer integration with the other speakers. If you set the speakers to small after then the speakers and subwoofer will only cross over to their set frequencies. The rest is just graphs - not how things will play out - this is not the only method you can use to setup, but one I found easy. I do mention for safety reasons separating the speakers after in dirac and checking the roll offs at the extremes to ensure no over eq is done in the wrong places. Thats a just in case measure

@photomusicman9413

6 жыл бұрын

Pursuit Perfect System Thank you very much for explaining. I understand it a bit more now.

Hello, after the new update are there any changes in the way to setup the AVR ?

@PursuitPerfectSystem

6 жыл бұрын

inception74 this is a setup video for after the firmware that enabled Dolby Vision and made changes the bass management around Dirac Live

@jenniferandfreddiemendoza7651

4 жыл бұрын

In case you were still wondering the answer is no

Is it still the case that the speakers should be set to Large at the beginning?

@PursuitPerfectSystem

3 жыл бұрын

not with newer firmware

with the new firmware on arcam and dirac 2.0 would this be the same?

@PursuitPerfectSystem

4 жыл бұрын

no some of this is out dated now

Hello how high do you set the volume in the back of your subbwoffers and do you manually set them whit dsp (75db) before calibrate whit dirac ..? You also have 2 subbs so how do you best set theme up before dirac when dirac youst calibrate for 1 subb..? Best regards

@PursuitPerfectSystem

6 жыл бұрын

Peter J I have the volume on my subwoofers set to nearly maximum. In an ideal world you dont want to use multiple equalisations but in practice you might need to. In my instance I have 2 very big room peaks in frequency response. One you can see in this video. When I run dirac measurements those peaks clip the measurement so I have to reduce the channel volume to stop it. This results in too low overall reading for the subwoofers . So I do use the manual dsp in my subs to reduce the peaking frequencies some so I can measure the subs at a higher volume in dirac. I hope that makes sense in what I am explaining there.

@kenzo06ful

6 жыл бұрын

Pursuit Perfect System Ok thanks for answer..:-)

@kenzo06ful

6 жыл бұрын

Pursuit Perfect System Hello again Do you measure both subwoofers in the dirac calibration, or do you only measure subwoffer 1 and set the second subwoofer after the first one manually..? Best regards

@PursuitPerfectSystem

6 жыл бұрын

Peter J Hi Peter measure both mate

@kenzo06ful

6 жыл бұрын

Pursuit Perfect System Ok And you have Nearly full volume on the subbs that you have setup similar db and meter before dirac.? I probloby set to half volume. And max in the dirac setup green 12db volume before calibration..?

Hi, I`m using Arcam AVR390 and I`ve done the measuring steps and I just find out that the Dirac software have bass control feature as well...Can you tell me please how I can get this feature on the Dirac software for Arcam AVR390. Thank you!

@PursuitPerfectSystem

3 жыл бұрын

The AVR 390 doesnt support Dirac Bass Control

@alinchirca

3 жыл бұрын

@@PursuitPerfectSystem Thank you!

@alinchirca

3 жыл бұрын

Hi again, Hope I didn't disturbing you... I got few more things to ask if is ok?!?! I watch all your reviews about Dirac and Arcam AVR's and it help me with my setup a lot... Now the questions are... First one... I'm using only one subwoofer Dali E 12F after the measurement if I connect the cable through the LFE the bass doesn't sound to deep but if I connect on the Left and Right input to the subwoofer using both pre amp subwofers (Sub 1 and Sub 2) bass it is much deeper how I like... Now is ok to using like that? Do I loose the crossover?!?! The second is...After I do the measurements, when you go at the end on the filter design you have down on the bottom thew things, first allready ticked (Measured) leave like Dirac it setup, the bass looks like it sound from one side were is the subwoofer only, if I tick on the right side were it show (Corrected) Spread option the bass is deep and looks like is come in from all speakers... Which I like more how it sound the bass. Is ok to keep the settings how I like or that Spread thing it just make the sound weard, I mean all the channels are not doing that sound accurate like without tick the Spread option? I mean the channels instead send the the sound in the right speaker when you watch a movie it just mix them up with this option... I do appreciate if you can give me an advise about all this... My sistem setup is 5.1.2 (front speakers Wharfedale 11.3, surround speakers Wharfedale Diamond 220, center SVS Prime, atmos upfiring Mission's and subwoofer Dali E 12F) Thank you and take care!

Hi great video seems a bit strange changing the levels after Dirac has set them surely this would change everything :-)

@PursuitPerfectSystem

4 жыл бұрын

I agree, however with this range of Arcam AVR's it very often sets the channel levels stupidly high which means when you crank the volume the sound can distort and the unit can shut off. I have found you can get better overall sound by setting the speaker levels more appropriately and when you turn the sound up you don't get any distortion

@gingerninja7187

4 жыл бұрын

Pursuit Perfect System was wondering is say just reducing each level by 8-10 I’m proper peed at the moment as I updated my 860 processor and it’s wiped the calibration ,and original had the Dirac done from where I purchased it ,so need to go threw the whole process again 🤯

@sevans1966

4 жыл бұрын

Was planning to configure Dirac on my Arcam AVR550 so thought i'd give the video a look first. I have to admit i have no idea what any of that meant 😱 Think i'll leave it.

@PursuitPerfectSystem

4 жыл бұрын

@@sevans1966 I provide a home and remote online dirac calibration service if that is something you are interested in. Your probably only hearing about 50% of what the 550 can do depending on certain factors of course, you can see examples of my work on my website. www.pursuitperfectsystem.com

@gingerninja7187

4 жыл бұрын

Steve Evans Hi ,have no fears with Dirac live ,I have the arcam av860 ,and was intrested in doing the calibration myself ,so purchased the umic-1 microphone as this is what’s recommended ,then came the day to do the calibrating ,before anything I watched the how to tutorials about Dirac on KZread ,it’s very simple to follow ,just common sense ,anyway after moving the microphone between the positions it comes to what look like a screen of confusion ,but not so bad ,I found its best to link all speakers together so Dirac does one for all once this is done make sure you save it ,so you can go back and make changes with the target curve ,as this can be done until your heart is content ,do remember the target curve is set by Dirac and you could just leave it at that ,but most people make adjustments ,to suit ,by giving it ago yourself won’t cause any problems ,but would recommend watching the Dirac tutorials ,and vids on pursuit perfect system ,that’s the best starting point ,and regarding changing the levels on your receiver / av after Dirac has done its magic no! I left mine as is ,as it doesn’t make any sense to change ,good luck

If you're on a Mac, your only option in reformatting a USB stick that will work with the Arcam is to download Paragon's NTFS formatting tool. While Mac Disk Utility will format any OTHER windows format, it won't do NTFS. And of course, that's the only format the Arcam will accept. After 30 minutes wasted, it says it's updating.

@photomusicman9413

6 жыл бұрын

No, I have a Mac and you should format the USB stick to MS FAT. Works perfectly on the Arcam.

Does the 90deg calc file come with the mic? Thanks in advance

@PursuitPerfectSystem

6 жыл бұрын

R J you download the files from minidsp using your Mic serial number to get the specific file for your mic

@RJ-um9ed

6 жыл бұрын

Thanks, I can't get the mic that came with the unit to work, so I decided to purchase the minidsp

Have dirac removed the process tab fron dirac 3

@PursuitPerfectSystem

2 жыл бұрын

Dont think so why

Is this the same setup for NAD?

@PursuitPerfectSystem

3 жыл бұрын

Yes its same setup procedure for all Dirac - but a lot of whats in this video was specific to these Arcam unit at the time and not necessarily something you need to follow now such as setting speakers to large etc

With changing the line levels set by Dirac doesn’t that have an effect on volume coming out of the speakers and making it not as clear for listening Say for example the centre is now louder than the fronts so it’s harder to hear them I’m not sure why Dirac sets it like this I just assumed that’s the way it should be to maximise the sound

@PursuitPerfectSystem

5 жыл бұрын

The channels need to all be balanced, yes changing the trim levels effects their output volume but if you balance the whole system its not an issue and can be a good thing for a few reasons

@gingerninja7187

5 жыл бұрын

Pursuit Perfect System Hi I’ve been told the Dirac live setup sets the levels to Dolby spec as if I play the 7.1.4 demo on the atmos disc all the levels are correct But when I did this on my denon avr it was miles out and would have to adjust have you come across this ?

@PursuitPerfectSystem

5 жыл бұрын

@@gingerninja7187 Being honest I dont think the arcam sets the levels well at all after a dirac calibration. I am sure they are all in the correct place for balance however they can cause the arcams to overheat and shutdown which is unacceptable. I set them manually as a result

@gingerninja7187

5 жыл бұрын

Pursuit Perfect System Hi maybe I’m not going to have the over heating problem as I’ve got the av860 so no amps I’m very intrested with the videos you do and would like to experience your system personally do you invite 😉

setting all speakers to large , is that only for the 850 ? or 550 also

@PursuitPerfectSystem

5 жыл бұрын

it's a process for measuring so yes same for all models

@checkbox1234

5 жыл бұрын

@@PursuitPerfectSystem thanks for taking the time to do this video it's been really helpful . Great channel

@PursuitPerfectSystem

5 жыл бұрын

@@checkbox1234 you are welcome

I followed your video verbatum but have a question regarding resetting the speaker volume setting at the end of the setup utilizing a db meter to 75 db for all speakers and I notice the over all gain is quiet a bit less than not using the new Dirac settings . Is it better to just leave the settings that Dirac so I am not driving the volume up to compensate?

@PursuitPerfectSystem

5 жыл бұрын

75db is not important - it's not the number that's important but all the channels being at the same volume. Leaving the channel trims as dirac sets it would make sense except for in the case of my 850 it sets the L C R to +10db in the trip for no reason. I don't believe having any channel trim in +db as being a good thing. Turning the overall volume up is just fine in my experience better than having a high +db channel trim

@garykarczewski6678

5 жыл бұрын

Great I think what I will do is up the volume still using a db meter to the level which I hear when not using Dirac. This way the only thing really changing is EQ not volume.

Please let me know if you have any email to share the pictures of the measurements.

@PursuitPerfectSystem

6 жыл бұрын

Hi Jack my email is pursuitperfectsystem@outlook.com

Hi, I have a question. Where I can find calibration file for umik1? name file is 721120_90deg.txt.

@PursuitPerfectSystem

2 жыл бұрын

Minidsp website

@berj79

2 жыл бұрын

@@PursuitPerfectSystem Hi Terry, wanted to know if it's ok to set the Front Speaker levels to +4db? As my avr850 front pre outs are connected to an external amp & need it to that level for matching the other speakers. Will running them +4db hot cause any distortion or clipping? i only listen at moderate volumes around 50-55 on the avr850 volume scale.

@PursuitPerfectSystem

2 жыл бұрын

@@berj79 no your fine

@berj79

2 жыл бұрын

@@PursuitPerfectSystem Thanks for the reply, can i go to +5.5db for the front speaker levels on the avr850? or will that be too much? Thanks.

@PursuitPerfectSystem

2 жыл бұрын

@@berj79 it wont matter if you hear distortion back it off

Can it be umik 1 or only 2 for arcam avr 550?

@PursuitPerfectSystem

6 ай бұрын

Either work

@HaMMy24100

6 ай бұрын

@@PursuitPerfectSystem thank you for answer. Can i ask you if i may, i bought arcam 550 with elipson prestige facet f14, center 11c and sub 10. what settings would u recommend or on what should i be carefull? or is this video good for my set ? Thank you so much for help really, i dont know on who to turn on.

@HaMMy24100

6 ай бұрын

its one problem on another ... i came this far to the test but its getting me error because its to low. Do I must disable somehow speakers cuz he finds me 7+1 but i only have large speakers center and sub....

Sorry the picture did not upload, here are the measurement;front L 02.00ms, center 01.27ms, F right 02.00ms, surr R 05.58ms, s.back R 03.08ms, S back L 05.27ms, s L 07.39ms, but the real measurements front all speakers 11 feet, s R 5 feet, S back 8 feet. Please let me know the levels I should keep for over all.

Also no test tone is played on my sub at all

@PursuitPerfectSystem

6 жыл бұрын

Tim Schneider make sure you have selected it as a subwoofer when you set your levels

@PursuitPerfectSystem

6 жыл бұрын

Tim Schneider make sure you have selected the speakers to large and you have selected you have a subwoofer in the arcam menu before running dirac live

@schnitty78

6 жыл бұрын

I followed the instructions in your video exactly. I upgraded the firmware on the arcam to latest. Factory reset. Set my fronts centre and sides to large and enabled sub. I have my fronts by amped. In a three hour troubleshooting session last night I tried a range of different things with no success. Seems odd that the test tones are being sent to the wrong channels. When I get some time I'll do some more troubleshooting and just have one speaker active, then two, etc and build up slowly to my 5.1 setup to try and pinpoint. Just wondering if anyone else had encountered the same

@schnitty78

6 жыл бұрын

Thanks for your help, great video

@PursuitPerfectSystem

6 жыл бұрын

Tim Schneider you are more likely to get help on a forum like AV Forums than on here. It seems like there is a fault with the product which is really odd to have the one you have?? Sorry I can't help more

Arcam needs to get it's head out of its @ss when it comes to being user friendly. As a UX designer, I see so many missed opportunities to make life easier for the customer in this product. The fact that we even need a video on this stuff, in 2018, is ridiculous. In regards to the OSD, Arcam, Windows 95 called and they want their OS back. STOP leaving user navigation up to systems engineers. I'm on a Mac, and I just spent the past 15 minutes trying every drive reformat I can in order to get the finicky 850 to recognize the files on the stick... still nothing. Download files > copy to USB > plug USB in BACK of machine while pressing two buttons on the front. Read this crazy long PDF with info I don't need. Are you f@cking kidding me? A $500 PS4 UI destroys a $6,000 ARCAM OSD. This brick has Ethernet plugged in, right into the back, and yet its not smart enough to update it's own stinking software.

Huge disappointment! How on Earth you can call it a simple guide?!

@PursuitPerfectSystem

5 жыл бұрын

where did I call it a simple guide - it's called setup guide? to be honest you are the only person to mention this in thousands and this guide is a little out of date now anyway

@PursuitPerfectSystem

5 жыл бұрын

on another note you have just given Arcam thousands of your pounds, euros, or dollars - maybe you should follow the setup video guide they made?? as you have paid me nothing, they have paid me nothing and yet you are complaining about the fact I bothered to make a setup guide video, but one thats not simple enough for you to follow. There is something not quite right about this picture? Think about it mate please

@RS-do1of

5 жыл бұрын

Pursuit Perfect System incredible- absolutely incredible- this is an excellent video on a complicated subject. It has helped me to get my system singing. And you do it free. And people complain. Thank you sincerely