I am learning from you during quarantine. All tutorials you posted are treasures for me. Appreciated for the videos!

@AnsysTutor

3 жыл бұрын

Great to hear!

Thank you so much for the effort you put in these simulations. You make it look so simple sir! Every one of your tutorials has something new to learn. Thank you once again. I hope one day you'll post a simulation on sneezing/coughing with effect of airconditioning. :)

@AnsysTutor

4 жыл бұрын

Thank you for your compliments. We are trying day by day to bring such type of advanced simulation for you. Thanks again.

It's amazing. Very productive Thank you very much sir.

@AnsysTutor

4 жыл бұрын

Most welcome🙂🙂🙂

thats amazing

@AnsysTutor

4 жыл бұрын

Thank You 🙂🙂🙂

Great job , thanks sir, i would like to know how can we define a flow of particles (solid bulk mateial) and simulate it, did you have a video about that ?

@AnsysTutor

3 жыл бұрын

You need to use multiphase model for this.

@ayoubes.salehy1894

3 жыл бұрын

@@AnsysTutor yes sir thanks i found it

Is it possible to simulate single screw extrusion in Fluent? Thanks for your videos.

@AnsysTutor

4 жыл бұрын

Cant say about this, I have no experience on that.

Sir hi Is there a reference article on any platform of this shape?

@AnsysTutor

Жыл бұрын

I have mailed the reference research article. Please check.

is there any reference article related to this?

@AnsysTutor

Жыл бұрын

It was one of the request from a subscriber, there is no reference file for this.

Why the pipe wall is adiabatic in this analysis? Why not diabatic? Plz explain

@AnsysTutor

2 жыл бұрын

We are extracting the heat from the flue gas to the cold water. In order to prevent the heat loss to atmospheric air, we have given an adiabatic wall boundary condition on the pipe outer wall.

@farhankhalil5677

2 жыл бұрын

Thank you

In ansys 2020R2 ,why outline is not seen on screen,it makes difficult to proceed further process in meshing, appreciate your work ,u makes learning easy

@AnsysTutor

3 жыл бұрын

You might have altered the tabs position. Try to reset the mesh then open it.

@shortsfactory2484

3 жыл бұрын

How we apply helical screw on a curved tube,can you make a video on it plzzzz

@AnsysTutor

3 жыл бұрын

Please sharr the details of the geometry. if possible will try to make a tutorial.

Sir I have two questions. Que 1. In boundary conditions, under "outlet" why have we not used "mass-flow outlet" type for flue gas or water? But we used "mass flow inlet" type in "Inlet".. Que 2. For Outlet, why didn't we use the given outlet temperature?

@AnsysTutor

4 жыл бұрын

If you want the flow of air to be constant at the outlet you can use mass flow outlet . Like the case of exhaust fan , as we are unware of the flow at outlet so we cant use that., We have the data of inlet & going to find the results like velocity tempr etc at outlet.

@abhinavanand5584

4 жыл бұрын

@@AnsysTutor Okay okay sir. I understood.

@abhinavanand5584

4 жыл бұрын

Thank you sir.

Comment part 2... Question - Since we have not used any outlet data, Facet Average in Report also has affect of it. There is a change of only a single degree temp. But change should be large. Sir please clarify..

@AnsysTutor

4 жыл бұрын

As i had said earlier its a part of the model you had sent not the full economizer. The full body tempr variation would be definitely different from this.

@abhinavanand5584

4 жыл бұрын

Sir for comparing the "increase in heat transfer rate due to fin" , how can I show that through the analysis?

@AnsysTutor

4 жыл бұрын

You need to do another model with no helical fins then find out the heat transfer. Then compare with the previous one.

@abhinavanand5584

4 жыл бұрын

@@AnsysTutor Okay sir.

how did u get the geometry???

@AnsysTutor

4 жыл бұрын

It was requested by one viewer.

Why doesn't the continuity equation ? It's residual is around 1e-02.

@AnsysTutor

3 жыл бұрын

every residual has been changed to 1e-6 , which on are you referring to? . specify the time.

@mushfiqurrahman8810

3 жыл бұрын

@@AnsysTutor Thanks for replying. See 9:49 . Only energy equation residual is below 1e-6. Others are above. And they are oscillating too.

Sir how you learn all this its wonderful 👍

@AnsysTutor

4 жыл бұрын

Thank you. Its all about learning from various teachers & CFD professionals.

Hello sir i need your help about fluid fluent

@AnsysTutor

3 жыл бұрын

Yes, please ask.

@haseebchoudhary8917

3 жыл бұрын

@@AnsysTutor My topic is Simulation convective heat transfer super critical carbon dioxide in spiral finned tube , I am beginner , i made design and meshing , but i do not know how to do setup is there anyone who can make a case model for me , i will pay to him

@AnsysTutor

3 жыл бұрын

Sorry, Haseeb. Currently loaded with some works cant help you regarding this. I can only answer your queries.

Plz attach the geometry file

@AnsysTutor

4 жыл бұрын

you can download it from imojo.in/helical_fin

@AnsysTutor

4 жыл бұрын

kzread.info/dash/bejne/eoOEq5due9Snlaw.html

没有字幕 真难啊QQQQQQAQ

@AnsysTutor

4 жыл бұрын

您可以使用Google翻译应用将其翻译成中文

@bloneboby4107

4 жыл бұрын

@@AnsysTutor 谢谢 我试试，有没有搭配的计算流体力学理论书推荐呢？我理论知识太差了。。。

@jasonwang7960

4 жыл бұрын

@@bloneboby4107 刚开始学吗