ANENG SZ305 1000VDC,750VAC 2000COUNTS MULTIMETER,made in china.
Жүктеу.....
Пікірлер: 25
@apn13843 ай бұрын
Thanks for the very detailed test! Special thanks for disassembling and showing the internal contents!
@wilsonluilui
3 ай бұрын
thx for watching
@_BestFriendАй бұрын
проверка ёмкости до 20mF - шикарно. Спасибо за обзор и тесты. Успехов!
@wilsonluilui
Ай бұрын
thx for watching.
@druid9702 ай бұрын
I have sz305 voltage mode - resistance = 9.8M ohm on red and black probe battery test mode - resistance = 500ohm on red and black probe battery test mode 12v-maximum to test up to 20v your video clip perfect to reviews thank you.
@wilsonluilui
2 ай бұрын
thx for watching sir.
@luizmello70205 ай бұрын
Obrigado pelo teste completo senhor Wilson 😃
@wilsonluilui
5 ай бұрын
thx for watching❤
@luizmello7020
5 ай бұрын
Hello Mr. Wilson, can you tell me if this ANENG SZ305 model reads in TRUE RMS?
@wilsonluilui
5 ай бұрын
@@luizmello7020 you must make caculate by Vmax X 0.707
@wilsonluilui
5 ай бұрын
or choice aneng 616.it true rms not use to any calculated.
@luizmello7020
5 ай бұрын
I'm thinking about the low cost option SZ304...do you think I can trust ?
@Gamersfanko2 ай бұрын
Thanks, very good!
@wilsonluilui
2 ай бұрын
thx for watching.
@sardarrahatul46877 ай бұрын
Hi Wilson. Which one is better aneng 616 vs aneng 620 ?????
@wilsonluilui
7 ай бұрын
620A aneng is easy to buy the testing pen.and 616 is hard to buy the test pen .sir
@pault65337 ай бұрын
Appears there are large holes for a proper shunt wire to be soldered, but they tried to save money. Instead of this wire they put a 10 milliohm resistor between 10A input and common and put a note on the front of the unit maximum 10 seconds. However, no warming in the manual. Time to lubricate that selector wheel. It's so dry, and the spring arms really get driven down into the crests of the case. They will break prematurely without grease. With no white mark on the selector indicator, you don't know which way the wheel is turned at a glance, could result in wrong range. They also forgot to install the transistor receptacle. I will be very difficult to get the transistor wires to all three touch the PCB.
@wilsonluilui
7 ай бұрын
it company mistake or save their money,make a low prices multimeter,😕
@hoangviet80054 ай бұрын
The circuit board is too sketchy
@wilsonluilui
4 ай бұрын
thx for watching,it aneng design circuit for an low prices meter.
@danialtun54317 ай бұрын
This multimeter is no fuse
@wilsonluilui
7 ай бұрын
yes,no fuse ,in mA only have resistor for protection,and other is a PTC ,IT MUST BE BROKEN meter main IC if you wrong testing in current position. before i burned three of this type meter be careful.
@sardarrahatul46877 ай бұрын
Hi Wilson. Which one is better aneng 616 vs aneng 620 ?????
Пікірлер: 25
Thanks for the very detailed test! Special thanks for disassembling and showing the internal contents!
@wilsonluilui
3 ай бұрын
thx for watching
проверка ёмкости до 20mF - шикарно. Спасибо за обзор и тесты. Успехов!
@wilsonluilui
Ай бұрын
thx for watching.
I have sz305 voltage mode - resistance = 9.8M ohm on red and black probe battery test mode - resistance = 500ohm on red and black probe battery test mode 12v-maximum to test up to 20v your video clip perfect to reviews thank you.
@wilsonluilui
2 ай бұрын
thx for watching sir.
Obrigado pelo teste completo senhor Wilson 😃
@wilsonluilui
5 ай бұрын
thx for watching❤
@luizmello7020
5 ай бұрын
Hello Mr. Wilson, can you tell me if this ANENG SZ305 model reads in TRUE RMS?
@wilsonluilui
5 ай бұрын
@@luizmello7020 you must make caculate by Vmax X 0.707
@wilsonluilui
5 ай бұрын
or choice aneng 616.it true rms not use to any calculated.
@luizmello7020
5 ай бұрын
I'm thinking about the low cost option SZ304...do you think I can trust ?
Thanks, very good!
@wilsonluilui
2 ай бұрын
thx for watching.
Hi Wilson. Which one is better aneng 616 vs aneng 620 ?????
@wilsonluilui
7 ай бұрын
620A aneng is easy to buy the testing pen.and 616 is hard to buy the test pen .sir
Appears there are large holes for a proper shunt wire to be soldered, but they tried to save money. Instead of this wire they put a 10 milliohm resistor between 10A input and common and put a note on the front of the unit maximum 10 seconds. However, no warming in the manual. Time to lubricate that selector wheel. It's so dry, and the spring arms really get driven down into the crests of the case. They will break prematurely without grease. With no white mark on the selector indicator, you don't know which way the wheel is turned at a glance, could result in wrong range. They also forgot to install the transistor receptacle. I will be very difficult to get the transistor wires to all three touch the PCB.
@wilsonluilui
7 ай бұрын
it company mistake or save their money,make a low prices multimeter,😕
The circuit board is too sketchy
@wilsonluilui
4 ай бұрын
thx for watching,it aneng design circuit for an low prices meter.
This multimeter is no fuse
@wilsonluilui
7 ай бұрын
yes,no fuse ,in mA only have resistor for protection,and other is a PTC ,IT MUST BE BROKEN meter main IC if you wrong testing in current position. before i burned three of this type meter be careful.
Hi Wilson. Which one is better aneng 616 vs aneng 620 ?????
@wilsonluilui
7 ай бұрын
🙏