Amazon CO-Z gate opener WiFi set up. using Nexx garage opener.
you should be able to use any other opener with the shorting option. WiFi enabled.
Жүктеу.....
Пікірлер: 23
@narvingumbs23056 ай бұрын
Hey, Have you figured out your problem yet. I just installed a Shelly Plus 1 on the same CO-Z gate motor. We have the same control board, but my manual has a slightly different DIP switch set up. That worked for me. Try turning OFF only switch 1 (DOWN) and leaving 2 & 3 ON (UP). That did the trick for me. before, all I could do was close the gate when open as the common and close pins were used, so that is the only way the gate will run, however with DIP switch 1 (ONLY) in the DOWN position. it works just like the control fob. open, Stop, Close etc. Hope it helps with your situation.
@awakeningseries66093 жыл бұрын
You may not have configured your magnet right..... also the wifi thing comes with a magent-selonoid sensor that you need to place at the right place. It could be just that.
@sergioesquivel47843 жыл бұрын
The reason why your garage is getting stuck it's because the sensor is pushed too much to the back try play with it so you don't have that issue.
@leebriand530511 ай бұрын
No problem…Thanks
@elmachuquin3 жыл бұрын
I think you have to grease the flux capacitor the muffler bearing and change the fuse on the thermal coupler you should be OK after that.
@elfocker
3 жыл бұрын
You could be right, lmao
@elfocker
3 жыл бұрын
Pinché enano 🤣🤣
@leebriand530511 ай бұрын
Did you ever find the answer to ur problem because I can’t get mine to work with the Wi-Fi module that it came with
@Mrkool2462 жыл бұрын
Do you know which terminal I should use to power my Wi-Fi gate opener… you vid help out a lot this whole time my dip switch were on smh. Right work fine fine but I heard you can get power directly from gate control board to power on Wi-Fi gate opener came with 2 wire red and black.
@elfocker
2 жыл бұрын
I'd have to look into that. Thanks
@gtdodgeviper3 жыл бұрын
About the switches. You only need the first one to be down the other 2 are for your gate go close automatically after a certain time. I just installed my motor and I have noticed the same problem where some times It doesn’t open or close. It does it just like yours only moves like half an inch. But mine does it with the original remote controller. I checked my magnets with a multimeter to make sure that they are in the right position and they are. Did you found out what causes your gate to not close after opening all the way?
@elfocker
3 жыл бұрын
Unfortunately I still have that problem with it not closing when open all the way. But the alarm status and notifications fixed it self and I have real time notifications. I really haven't had time to look into it, but when I do I'll post something. Thanks
@84848AR Жыл бұрын
Where did you get your gate painted? I want my old gate painted that color but not sure where or what color is it called? Thanks!
@elfocker
Жыл бұрын
It's actually a powder coated Bronze. It was done before it was installed. Thanks
@84848AR
Жыл бұрын
@@elfocker oh looks nice thanks for the info
@shirleyknowles8119 Жыл бұрын
Which appt can I use for the CO-Z gate opener?
@leebriand530511 ай бұрын
Did you ever figure the problem out when is was opened and you went to close it
@elfocker
11 ай бұрын
Well shortly after that video one of my dogs chewed up the exposed wires and I kind of gave up. It's been a while so maybe I'll try again. Lol. On a side note the gate opener has not failed me once 🔥. It's a workhorse, that thing opens at least 6 to 10 times daily. Sorry I don't have an answer for you.
@aaortega942 жыл бұрын
Do you do house calls?
@elfocker
2 жыл бұрын
🤣
@robertovallecillo64062 жыл бұрын
Have wifi repeater close by so can get better signal
@robertovallecillo64062 жыл бұрын
First u need a repeater close by n seconds u need connect limit switch normally close to work right
Пікірлер: 23
Hey, Have you figured out your problem yet. I just installed a Shelly Plus 1 on the same CO-Z gate motor. We have the same control board, but my manual has a slightly different DIP switch set up. That worked for me. Try turning OFF only switch 1 (DOWN) and leaving 2 & 3 ON (UP). That did the trick for me. before, all I could do was close the gate when open as the common and close pins were used, so that is the only way the gate will run, however with DIP switch 1 (ONLY) in the DOWN position. it works just like the control fob. open, Stop, Close etc. Hope it helps with your situation.
You may not have configured your magnet right..... also the wifi thing comes with a magent-selonoid sensor that you need to place at the right place. It could be just that.
The reason why your garage is getting stuck it's because the sensor is pushed too much to the back try play with it so you don't have that issue.
No problem…Thanks
I think you have to grease the flux capacitor the muffler bearing and change the fuse on the thermal coupler you should be OK after that.
@elfocker
3 жыл бұрын
You could be right, lmao
@elfocker
3 жыл бұрын
Pinché enano 🤣🤣
Did you ever find the answer to ur problem because I can’t get mine to work with the Wi-Fi module that it came with
Do you know which terminal I should use to power my Wi-Fi gate opener… you vid help out a lot this whole time my dip switch were on smh. Right work fine fine but I heard you can get power directly from gate control board to power on Wi-Fi gate opener came with 2 wire red and black.
@elfocker
2 жыл бұрын
I'd have to look into that. Thanks
About the switches. You only need the first one to be down the other 2 are for your gate go close automatically after a certain time. I just installed my motor and I have noticed the same problem where some times It doesn’t open or close. It does it just like yours only moves like half an inch. But mine does it with the original remote controller. I checked my magnets with a multimeter to make sure that they are in the right position and they are. Did you found out what causes your gate to not close after opening all the way?
@elfocker
3 жыл бұрын
Unfortunately I still have that problem with it not closing when open all the way. But the alarm status and notifications fixed it self and I have real time notifications. I really haven't had time to look into it, but when I do I'll post something. Thanks
Where did you get your gate painted? I want my old gate painted that color but not sure where or what color is it called? Thanks!
@elfocker
Жыл бұрын
It's actually a powder coated Bronze. It was done before it was installed. Thanks
@84848AR
Жыл бұрын
@@elfocker oh looks nice thanks for the info
Which appt can I use for the CO-Z gate opener?
Did you ever figure the problem out when is was opened and you went to close it
@elfocker
11 ай бұрын
Well shortly after that video one of my dogs chewed up the exposed wires and I kind of gave up. It's been a while so maybe I'll try again. Lol. On a side note the gate opener has not failed me once 🔥. It's a workhorse, that thing opens at least 6 to 10 times daily. Sorry I don't have an answer for you.
Do you do house calls?
@elfocker
2 жыл бұрын
🤣
Have wifi repeater close by so can get better signal
First u need a repeater close by n seconds u need connect limit switch normally close to work right
The chains are twisted