Amazing Breathing LED Circuit
Ғылым және технология
Hi ,
This video is to show you how to make a simple breathing LED circuit using 555 IC.
◾ Buy 555 IC - amzn.to/3cDa7ar
◾ Other suggested videos -
1. 434Mhz transmitter and receiver -
• 434Mhz Wireless Transm...
2. New style LED chaser -
• [New] LED Chaser Idea ...
3. Colour changing LED chaser -
• WOW! 7 Step colour cha...
#Electronics_Project #Fading_LED
#ESTechKnowledge
Пікірлер: 45
Looks like a fun project. Thanks for the upload.
Great work brother
very easy to follow, thank you ❤️
very cool
If I wanted to make this circuit using a 3V source and more LEDs in the circuit, would I need to change the resistors??
@pr0fessoro
7 ай бұрын
it is not possible (timer 555 need minimum 4,5 v supply voltage), but you can use dc-dc step up converter and lower 180 ohm resistor if you use more leds, you need replace bc547 with more powerful transistor ...
Amazing
@jobbe-wijnen
Жыл бұрын
is that an NPN or a PNP transistor (why not post a schematic at the end of your videos?)
What is the output voltage? I want do something like this with a 12 Volt LED strip in my car. What is the configuration for 12v in and 12v out?
Good goob thanks
@-throat-
Жыл бұрын
Goob
इसमे rgb led use कर सकते हैं क्या
with 5V I just can't get it to breath. I did change some of the values, importantly the resistor in series with the LEDs, but also the other resistor and capacitor. It does rise slowly, and then just stays on. I can imagine the voltage drop of the 555 is too large to operate this circuit with 5V. Or perhaps the specs of the transistor are critical, because I did use another npn
Can this circuit support usb?
If I want a 5V source, since it is minimum specs, will this work or do I need to use different resistors?
Would it work with a 5.5v solar cell?
5v pe chalega kya?
Will this work for any amount of leds?
Tem como adicionar um sensor de luz
Ware is led + comming?
Excellent. What if I want to run 20 LED's and have the breathing speed up just a tad? Do you answer any of your comments?
@yoranwyns8716
Жыл бұрын
For the speed you can change the value of the capacitor. And you can do 20 leds but then it's best to provide each led with its own resistor. I hope what I'm telling is right but that's just what I think.
@jobbe-wijnen
Жыл бұрын
I think with 20 Leds the circuit is the same (because parallel LEDs have the same voltage drop as just one LED) and the timing is likely controlled by the value of the Capacitor. So smaller capacitor is faster frequency. Is my guess. but I am going to indeed try what you propose. Note that different color leds need different value of resistor on pin 1. this is easy to google, you'll find it.
This mode is really safe for people who has disabilities though. I understand that there is a warning label but wait there is a mode selection.
Shematics plz???
What should i change when i use 5volt batteries?
@jobbe-wijnen
Жыл бұрын
My question too. 😊
hello.is it possible with the current setup to run at 12volts?
@estechknowledge
Жыл бұрын
Offcourse
@dreadpointgr96
Жыл бұрын
@@estechknowledge ty verry much
@Vib-Ribbon_2763.
Жыл бұрын
@@dreadpointgr96 no ty
How many leds can be powered with this circuit?
@estechknowledge
3 жыл бұрын
Less than 10 LED
Triangle wave
can i use 12v voltage in ?
@jooeybabbabooey
8 ай бұрын
Give it a shot, maybe put a bigger resistor
Can any other color led be used in this circuit?
@neubivashka.
2 жыл бұрын
Yep, just use proper resistor
Does this circuit work from 5V USB?
@jobbe-wijnen
Жыл бұрын
i cant get it to run
I hope you put the equipment and the instrument name you use. Its hard to identify what specific instruments/equipment to use for that project. Just recommendeding. Peace✌️
470uf you used? 16v? 25v 35v?
@estechknowledge
3 жыл бұрын
Use more than 16V
@ivansutanto89
3 жыл бұрын
If i used 14 leds in this circuit, can this circuit handle it? Because i tried it before and not work, 14 leds 9v, please your advise my friend
@neubivashka.
2 жыл бұрын
@@ivansutanto89 green led is 2.2-3.5V, so with 9V supply you can use only 3 leds.