i run a amadan 04pc very similar. i don't make as much as the others do buy im working on it. ive ran it for 2 years now, i love it thanks for the video

@prakashsati5742

7 жыл бұрын

I want job

Está amada ,es muy parecida a la que está en mi trabajo. Yo soy mecánico y le fabricó las herramientas, una de las que hice fue ,para perforar 80 barrenos de un 1/8 , de un golpe .

Mr.Operator ,just a little suggestion for safety to avoid the crash ,need to bend corner's , so it doesn't catch the bottom tool covers when the carousel spin ! 🤗😊🤗

@jdoublem_lo8240

3 жыл бұрын

What is a carousel are you talking about the turret

I miss this!

I've ran several of these Amanda's, there a very reliable machine,if taken care of 👍

@gregbeaver5244

2 жыл бұрын

We had the first Viprose 357 it was prototype with 4 auto indexes. I ran it after lunch to keep it running. Ours ran 24 hours a day 6 days a week. Yes they are very good machines.

@Againstthegrain247

Жыл бұрын

Hey can you give me some feedback please

i used to run these babies!! i miss it!!!!

i miss it too,,

i worked in japan with this machine, is excelente machine very eficient

@techcadsolutons

7 жыл бұрын

HELLO! Please helps pay with any manual of this machine, to put in the work that I did not experience. Please helps pay for. My email is gaxhini@gmail.com

i used to opreate that machine...that and the S and N express and the euro mac...metal punchers

So I work at Spec Built Systems and I’m at SpotWelding Area, but they want me to move to nc punching area. Can you tell me please if is it easy? Im kinda nervous using these machines

It's a lot cooler in person, you can feel the strikes through the air/ground. It's like when a train drives by.

@nickyaekle280

7 жыл бұрын

Especially on 7 ga material and up!

@gregbeaver5244

2 жыл бұрын

He was running thin gage stainless steel. There wouldn't be much to feel. I use to work in a sheet metal shop. I've ran a Viprose 357 before. It's a very good machine. But mostly I was a setup operator for the Break Presses. The punches we had were The Viprose, Pega, Pega 2 , And a Vella. We also had a cell that loaded and unloaded the sheet metal. The Break Presses were 2 Fab 50's and a Fab 100 , 2 Verson manual Presses and a Pasific Hydrolic 12 foot. And 3 Komatsu Presse.

I thinks he's running it on F 2 maybe

Or maybe the turret would grab the sheet and send it sailing out the back I've seen that at my factory

I was hoping the tooling would jam in the turret

@rogerroger7734

4 жыл бұрын

Michael niceguy nothing worse than that wrinkling sound and then hearing a cut airline from the clamp lol! Good times

I love running these machines I know every g code for them basically I can make these machines due back flips for you haha

@zoddie

4 жыл бұрын

Is it possible to punch out parts and not have microjoints or punch in such a way that there are no microjoints at the end?

@jdoublem_lo8240

3 жыл бұрын

Tell me these codes G27 G28 G66 G36 G37 G90 G92 G93 G98 G50 That's only a few I can remember do you know any laser g codes try me

I'm appalled at the lack of safety, NEVER put your hand on a piece of moving sheet metal.

@cky163100

8 жыл бұрын

what a bunch of kids crying about hold the shit while it's moving.

@stoneymontana5051

7 жыл бұрын

lol I watch our laser opperater pull parts out of sheets being cut all the time

@cky163100

7 жыл бұрын

lol these pussies must work in a shop full of Nazis for supervisors.

@wsantalitz7785

6 жыл бұрын

Holding the sheet overhang is right but how it's done really is squat in front of the table and let the overhang slide on your head. It's what jeremy does and it's the best practice.

@Againstthegrain247

2 жыл бұрын

@@stoneymontana5051 yeah parts being cut by a laser, the sheet is not moving. Js.

Nice nestting.

what is the preferable environment to keep these machines?...does it need air conditioning?

@cky163100

8 жыл бұрын

f2 with a m08

Surprised you don't have a loader

Ye mashin kitna seet ek bar mar sakte hai sir ji

Do you guys ever clean all the slugs under the turret?

@ChrisPlatt9740

9 жыл бұрын

I know I had to at my old job. Boy, those things get so clogged up that it even jammed up the turret.

@stoneymontana5051

7 жыл бұрын

ours has a little conveyer belt that we run to a scap dumpster to collect slugs. doesn't get them all but a good amount

@techcadsolutons

7 жыл бұрын

HELLO! Please helps pay with any manual of this machine, to put in the work that I did not experience. Please helps pay for. My email is gaxhini@gmail.com / arber.faca@gmail.com please help me

@tempi0039

5 жыл бұрын

+ARBER FACA hello

how to separate this parts from sheet with safely way without using manual method of osculating it? because it's very harmful for worker back.

@hankcuntpunt7166

9 жыл бұрын

I remember putting the whole staff of sheets in a machine and a suction cup or something would pick it up one piece at a time. that was almost 20 years ago though work in sheet metal shops in the winter when roofing was slow for me. but yes I seem to remember an automated version of this machine where you put the whole stack of sheet metal in and and arm picked up the pieces one at a time

can you send for me the explain parameter

I'm being trained to run one of these. The operator training me makes 18.50 per hour I'm learning everything.

@cky163100

7 жыл бұрын

it's easy once you get the hang of it. been running amada turrets and lasers since 2001.

@carlosrogers4873

7 жыл бұрын

Do you have any advice when running these machines I sure could use some.

@cky163100

7 жыл бұрын

the best advice is to keep a pen and paper in hand and take notes, hopefully the person training you knows what they are doing, and if they do then you should be fine. it's easy once you get the hang of it, I've ran the one in this video, a vipros, but right now I'm on a Pega. I ran a 2510 and that was sweet. I've also ran a finnpower p5 turret and that was cool.

@carlosrogers4873

7 жыл бұрын

Cool, thanks I will do that

@techcadsolutons

7 жыл бұрын

HELLO! Please helps pay with any manual of this machine, to put in the work that I did not experience. Please helps pay for. My email is gaxhini@gmail.com

Cnc turret patching machin opretar jawp sir

Where was this video taken.

@glenprice5511

2 жыл бұрын

Russia

Talk about unsafe. I would of been thrown out the door at my company.

This is an automated machine why does the guy keeps holding the metal sheet while the machine is operating, hes just waiting to get stabbed

I Laik

how much does a operator make? in USA?

@cky163100

8 жыл бұрын

I've been operating Amada turrets and lasers since August of 2001 and the highest amount I've made was 21.50 an hour. I'm currently at 17.5 where I work now.

Put that thing of F1

Sem machin jawp

AMADA : FURADEIRA - CHAPAS : ALUMÍNIO : RAPIDEZ - PRÁTICO - PRECISÃO - OPERAÇÃO - ROBÓTICS .

I like to alter stations

it is better than prima power cnc punching

Cuánto pagan por operar esta máquina se códigos lo que quiera soy mexicano

Sir I am looking for a job please do you need oparetor for turret punching mashin in your company 

@lalya_491_shooter..pradumn6

6 ай бұрын

And I am 2 years of experience

some turret need laser to complete...

I agree with phoenix pegasus! (Have been working with Amada machines for allmost twenty years now), both punching and laser. What the F**k is he doing inside the "working Area"!! Let the machine do the work!.

they used to crash alot...if you program it ti go too fast,...that machine will take that metal and shrivel it to a metal ball

no overide

Do this for work! Actually we are replacing our vipros right now !

@hirennavadiya

4 ай бұрын

Please help me for vipro 367 operation and some fault Well im in gujarat ahmedabad india. Help me big bro. Warm regards Hiren navadiya

@hirennavadiya

4 ай бұрын

Please send your email address I must contact you brother

おぉぉぉ～！

@KIENCAO_TV

6 жыл бұрын

京都 コーシン精密板金加工のスピー

OSHA would not be happy with him

This NCT not CNC

Hate running turrets, the laser is much better!

And make the matter worst the buttons such as emergency stop on the moving bed, this is zumba style operator, OSHA are you there ? lol

@nickyaekle280

7 жыл бұрын

In this video you can see 3 emergency stop buttons. 1 at the controller, on the bed and another to the left where the operator changes tooling.

i am turret panch programar

@mongoliancharcoal7018

3 жыл бұрын

I need turret punch programm

X300.Y10.T201; = bye bye clamp.........lol

@mahbubkabir1077

5 жыл бұрын

comonde

@mahbubkabir1077

5 жыл бұрын

commonde machine

s

NO SAFETY WORK

quiere perder sus dedos

That’s the model that pushed Amada in to Electric Ram machines. Worst model they ever made! Hydraulic failures!

Dude has no clue Not hard to program or run

@inkwell7571

Жыл бұрын

Turn it up dick. Thing runs so much faster than this

Dear I use first time in this m/c your model is 357 when I use 367 but some fault in this m/c. So can you help me some fault about this machine. Well my self hiren nava diya im from india gujarat ahmedabad city. Thanks with regard

I like to alter stations