All problems about Simjack Pro Pedal after 6 months of use (Review)
Ойындар
After a long work I finally finish the review.
It's been 6 months using Simjack Pro Pedal. A great pedal for the price with with some drawback.
in this video I will cover mostly the problems with this pedal. i'm sure they are a lot of review telling you how good it is.
So enjoy the video!!.
And if you are looking for alternative in similar price you can check out my Cammus LC100 and Thrustmaster T-LCM pedal.
Пікірлер: 76
To get angle on the pedals I turned the mounting plates around and swapped sides I can now angle the pedals backwards
@BoreyEngineering
11 ай бұрын
OMG Never considered that before! I will pin this post then!
@aeppikx
3 ай бұрын
did the same but than the pedals are way higher at the front what doesnt make it better
@David-G.T.D
3 ай бұрын
@@aeppikx I put a heal plate in front just a 1.5" board
That's actually a very good review. Thank you my friend....
Great video, lots of helpful information!
Valuable video, instant sub, thanks!
Maybe try using different elastomers (or skateboard bushings) for the brake and hope they're less sensitive to room temperature.
hola ,tengo la misma pedalera pero de la marca simsonn,son los mismos pero con celula de carga de 130kg ,no consigo ajustar los kg de la celula de carga en ningun lugar del software. utilizo freejoy 1,7,0. es posible ajustarlo!"???
how to make brake pedal less stiff? its too hard for me to push
Thanks for the video 👍🏻
Very informative, subscribed
What baseplate did you get? Where did you get it from? TY
Can The pedals be Mounted Inverted? do you have to modify anything to do so?
nice informative video
Good video, thanks.
The wheel stand at 5:40, do you use the Pedal base plate from Simjack? If yes, how do you screw the pedal plate to the wheel stand?
@BoreyEngineering
8 ай бұрын
Yes I screw simjack on base plate and screw base plate on the wheel stand plate
great video, just got mine in, thanks for the reiew.
@BoreyEngineering
11 ай бұрын
It still is a great pedal and now you know the drawback so you can easily avoid it.
I use a Heusinkveld sprint set and my brake broke. Now I need replacement before my sprints are repaired, do you think the simjack could be an alternative for the time? Are they better than the Fanatec clubsport? Those are the other „cheap“ pedals I’d consider using as my temporary replacement/backup.
@BoreyEngineering
11 ай бұрын
I never try fanatec. but if i’m in your position I will buy something that easily sell second hand.
@maddugqc6911
6 ай бұрын
ythea these are defenetly better than clubsport
Best updates: good Elastomeres or better replace them with Springs. 2nd. install the Heusinvield Ultimate + Upgrade Kit ( electronic box)
@Broodjemetbeleg
9 ай бұрын
Does it work out of the box? Very interested
@Jabbawock1972
9 ай бұрын
@@Broodjemetbeleg what out of the Box? the pedals or that Ultimate+ Kit? the Kit ....no if u want the elastomeres too because the Ultimate uses inner diameter of 8mm while the others have 10mm...but i dont use the elastomeres because i already changed it to aftermarket before
@TheBbarrow79
9 ай бұрын
@@Broodjemetbeleg yes you can use the new ultimate rod and elastomers and the control box. you just need a 15mm m8-m8 extension
@mesh6432
8 ай бұрын
what can we do about the wobble ? my pedals are new they dont wobble but if they start i wouldnt want that.. like my fanatec pedals never wobbelt left and right
@Jabbawock1972
8 ай бұрын
@@Broodjemetbeleg they does work...but..the geniue elastomere are just too soft...and about the electronic...its a very simple box and had to be calibrated with Diview and you only can have a linear curve....with the HE box its a much better software.
The fact that the resolution is not of great importance, are you judging from experience or from some kind of theoretical calculations? I just ordered these pedals and they are already on their way, and I found out about the low resolution after the purchase and I wonder if this will be a problem for me. Now I'm using Fanatec CSR Elite there are 1024 values.
@JesseGebauer
6 ай бұрын
How do you like the Simjacks?
Is your USB hub active (external power 5V) hub? This might help your readings be more stable between hub/direct to PC. As you seem to be very knowledgeable with engineering you could look at the sim-jack board and add some capacitance to the incoming 5V, maybe double. This might help stabilize readings as well. If you have access to purchase lock-nuts (nylon insert) it could help with your tightening/loosening issue. Good luck to hit 1000 subs.
@BoreyEngineering
5 ай бұрын
Thank you sir! i'm already sold Sim jack already. I hope I got more stuff to review soon!
Where do you get the base for the pedals?
@TheRivalryDrifting
8 ай бұрын
ailexpress
Had to use Heusinkveld elastomers and some spaces between the mounts the get rid of the rubber degradation and the wobble. So 250$ pedals become 300$ anyway. Still more affordable than Heusinkveld, but I think there are other brands like Cammus that might be more value for money.
I just use different springs for my brake, you can find them very cheap if you look for 3D-Printer ones. The default elastomers are really bad.
Have you checked how many positions the pedals actually have? Some write that there are no 10 bits, but in fact only 340 positions or so.
@BoreyEngineering
Жыл бұрын
about 0.2-0.4% per step, 300 step seem reasonable. 16 bit is the reading from raw value. but you can only use small part of the raw value range sooooo 300 step. You can see in for your self around 2:00 and watch it frame by frame. Anyway resolution don't matter very much. the game probaly smooth it for you anyway
@user-rh5wn9pd2d
Жыл бұрын
The fact that the resolution is not of great importance, are you judging from experience or from some kind of theoretical calculations? I just ordered these pedals and they are already on their way, and I found out about the low resolution after the purchase and I wonder if this will be a problem for me. Now I'm using Fanatec CSR Elite there are 1024 values.@@BoreyEngineering
@BoreyEngineering
Жыл бұрын
@@user-rh5wn9pd2d i'm judging from my experience. I don't know how to measure that difference. But I think equipment is not everything. it's all about the fun anyway
@user-rh5wn9pd2d
Жыл бұрын
Thanks a lot
@myonlineusername6015
6 ай бұрын
The red numbers are running smo other but The have a wider range so they change less with every mm of distance covered with hands. Idk what to watch. What article to read about this resolution issue?
Isnt simjack expensive? Like 300€ for pedal and 120€ for plate and 60€ for hub?
@BoreyEngineering
7 ай бұрын
I get to whole thing brand new under 300USD include shippping
I live in the Philippines which is much hotter though with more typhoon and rains so this is not recommended on a hot climate like is?
@BoreyEngineering
Жыл бұрын
if your temperature vary a lot then yes. But if you turn on aircon everytime you play then it is no problems
@losrevolucionarios8858
11 ай бұрын
@@BoreyEngineering sorry we don't have aircon so basically sim jacks are not recommended in warm / hot weather? I'll be using them with no AC in same tropical weather.
@BoreyEngineering
11 ай бұрын
@@losrevolucionarios8858 if change a lot from day-night then you might want to look at other pedal instead.
@Steve93K
11 ай бұрын
you just need to set a higher range of deadzone in diview. I live in malaysia and thats how i fixed mine. Havent calibrated in a year.
@BoreyEngineering
11 ай бұрын
@@Steve93K I understand. But if you play i hot temp you tap it a littlebit and it start reading instantly. and In cold temp you need to press it harder for it to start register. So it not really consistent
Very good review. Will you consider hydraulic instead? I stay in Camyand considering the hydraulic
@BoreyEngineering
9 ай бұрын
Right now i'm quite happy with Cammus pedal. Although I want to try hydraulic pedal but my budget wasn't allow me.
อยากสั่งซื้อเหมือนกันคับ อันนี้ simjack pro ไม่ใช่ simjack mini ใช่ไหมคับ เพราะขนาดฝ่าเท้าดูพอดีกับแป้น
@BoreyEngineering
9 ай бұрын
Simjack Pro คับ อยากได้ไหมผมปล่อยอยู่ สภาพดีไม่มีสนิม
@attha2
9 ай бұрын
@@BoreyEngineering ผมใช้แค่ throtte กับ brake แค่นั้นคับแอด
@BoreyEngineering
9 ай бұрын
@@attha2 เสียดายจัง ผมปล่อย 6500 คับ ตัวในคลิปเลย
Do you think it's worth upgrading from T-LCM? Very good video btw, love how in depth it was
@BoreyEngineering
6 ай бұрын
If you have found a good rubber on TLCM and You think the pedal is big enough for you (I wear shoes so TLCM is a little bit small to me) and if T-LCM pedal wiggle did not bother you very much. I think there's no reason to move to Simjack. Software and everything else is think TLCM is better than simjack.
So, you recommended cammus LC100 over this pedal set, right?
@BoreyEngineering
11 ай бұрын
Not really Cammus is also not perfect. I’m still keep looking for better pedal. Let me take some times to collect money and I will buy better pedal. maybe heusinkveld🤔. But for me I just like Cammus LC100 more because I don’t have any problems with themal expansion yet. It is probably less noticeable. But LC100 is squeaking a lot. Maybe I need to lube it a bit more. But I don’t want my rig to be too greasy
@ChevyBuddy
11 ай бұрын
@@BoreyEngineeringTry the Simagic P1000. They are absolutely amazing.
@ansonchin5674
10 ай бұрын
@@ChevyBuddyhave you tried both the simjack and the P1000? I have both in my shopping cart right now but am leaning towards the simjacks simply because they cost nearly three times less
คุ้มมั้ยครับถ้าจะจัด
@BoreyEngineering
11 ай бұрын
อยากได้ไหมคับผมปล่อย 6500฿ เลย55555
@OM-pq5mo
11 ай бұрын
ผมกำลังมองหาแป้นโหลดเซลซักตัวครับ ยังเลือกไม่ได้เลย5555 @@BoreyEngineering
34 degrees celsius inside 😰 damn, that's very hot, I woul'd die 😂 I have a comfy 18 degrees celsius inside
@BoreyEngineering
4 ай бұрын
I just enter summer and it's even warmer now....
Just change the rubbers problem solved LMAO
How to understand this without subtitles?
@ansonchin5674
10 ай бұрын
Just listen?
@fredmethot6116
10 ай бұрын
that sounded fucking racist mate... 🤬
hola ,tengo la misma pedalera pero de la marca simsonn,son los mismos pero con celula de carga de 130kg ,no consigo ajustar los kg de la celula de carga en ningun lugar del software. utilizo freejoy 1,7,0. es posible ajustarlo!"???
@xxxmandacaruxxx
Ай бұрын
Proba con la version 1.7.0b3, en este video kzread.info/dash/bejne/mKiB2KWLXazXZKg.html mencionan que la version mas reciente no funciona con solos Simsonn. El video explica como configurarlos. Espero te sirva.