If you want to have a look at those special videos become a member and join by clicking this link / @thinkingandtinkering
Жүктеу.....
Пікірлер: 344
@permanentmagnet2 жыл бұрын
Best video ever explaining this subject. Totally no nonsense and easy to understand. Bravo!
@infinitelyuniversal23904 жыл бұрын
Man where were you 15 years ago when i had to learn everything the Hardway!!! Your videos are Brilliant, straight to the point, and very easy to understand* Thank you professor 👍 😀
@ThinkingandTinkering
4 жыл бұрын
cheers mate
@smaqdaddy Жыл бұрын
You sir are a treasure! Just recently found your videos and am on a binge watching kick with them! Thank you so much for doing what you are doing!
@Herr_Bone4 жыл бұрын
I watched this video, although I knew already everything you were talking about. Your voice is so pleasant. One thing I would like to add to your explanation on how to find the two cables of one coil. There is a method to find the corresponding wires without any measuring instrument except your hand. Just connect two wires and try to turn the motor by hand. If it is hard to turn, you found the wires of one coil. Easy to do, but perhaps a bit more difficult to explain why this works. And a bit funny, because it already has to do with power generation. :-)
@kevinpersinger7957
Жыл бұрын
Thanks for the tip. Im gonna try that for isolating coils. I already identified it with a meter, but I don't always have that available(because i forget to plan sometimes). Good idea for a minimal survival if you need to generate power possibly too!
@CraigLandsberg-lk1ep
3 ай бұрын
Really glad to hear your comment 😅 I bought a heap of large stepper motors back in the late '80's and now I know how to use them, thanks for your comment 😅😅
@jonttan03
2 ай бұрын
Or just test it with your tongue 🙃
@AKIOTV4 жыл бұрын
I'd recommend parallel wiring for small wind turbines; with the series config you'll reach the target voltage at a lower speed, but as the turbine efficiency goes up with tip speed ratio (how fast it rotates relative to the wind speed) and small wind turbines have a tiny radius so a high RPM is needed for a high tip speed, you really want this thing to spin fast. Therefore it's probably a good idea to try and wire it up in parallel so that the target voltage is reached at a more optimal RPM. If you don't reach the target voltage this way, you can always decide to go back to series. Very nice video btw!
@ThinkingandTinkering
4 жыл бұрын
cheers mate
@mikael59143 жыл бұрын
You can figure out the wiring without a meter by shorting the wires and trying to turn the spindle/shaft. When the resistance increases with two wires shorted, you know they're both wires of one coil.
@pa_maj.MARTINI-van-MAN3 жыл бұрын
I've been looking for a while to find a good video with someone actually explaining things in detail. All I was finding were two hands and elevator music with bad video quality to go by until now, cheers mate 👍 This helped loads, subbed!
@Scott_C4 жыл бұрын
Love it. I've seen people use LEDs for their rectifiers, as those were the only diodes they had sitting around. Thought that was ingenious. Cheers!
@Plaasbakkie
4 жыл бұрын
I have done this aswell
@ThinkingandTinkering
4 жыл бұрын
it works just fine mate - most folks think a LED is for one thing only - but it is still a diode
@thesonnetist4583
3 жыл бұрын
Glad to know that. Thanks
@lucasvanhamburg4937
3 жыл бұрын
would't this heavily limit the current?
@erikr.johansen39923 жыл бұрын
Robert, I caught you just in time. Your "learn away skills" must be something you have had as a profession or something, calm voice, perfect dictation... And best of all, at least for me, perfect topics for Your videos, I'm learning A LOT. You are already successfull, but the sky is the limit for you're YT success. Greatings from Norway.
@richardseelye99384 жыл бұрын
Keep up the fascinating work you are showing us. You obviously stimulate free thinking, and for that I am very grateful.
@DimitriPappas
4 жыл бұрын
Agreed. This channel is wonderful
@ThinkingandTinkering
4 жыл бұрын
Wow, thank you mate
@Buzzhumma4 жыл бұрын
I used a mid drive 250watt bldc electric bike motor and used my bike to run my 50 watt tv with super capacitors . Worked great . It was the best energy harvester i made and i think the motor was perfect as it did not require much rpm to create the necessary 12 volts for the screen . It seemed to be around 100 watt i was producing for about 10 min and got 20 min telly time ! The key to its effeciency was using a 48 v ebike motor as the rpm could be low to get 12 volts out !
@ThinkingandTinkering
4 жыл бұрын
that is awesome mate - thanks for sharing
@CraigLandsberg-lk1ep
3 ай бұрын
Can I ask how you regulated it to provide the exact voltage? 😅 thanks
@oddjobbobb4 жыл бұрын
You never ever EVER cease to amaze! Thank you for taking the time to share your knowledge. I have a largish stepper motor from a surface sander. My younger brother overtaxed it and I replaced it from the nearby DeWalt store. I kept the old one, and now I know why.
@ThinkingandTinkering
4 жыл бұрын
awesome mate - I did't know DeWalt used them
@benreece76404 жыл бұрын
I'm learning more practical knowledge from you than 2years of military electronics training. I should have gone for fixing the motors instead of the weapons systems.
@Gwydion674 жыл бұрын
Great Rob, thanks! In theory rectifiers are dead easy to make, and I also know the different kinds with their pros and cons. But despite, until this day I didn't make a single one. Thanks to your reminder and your step by step tutorial I will do so and also go and repair my somehow failed crank-generator-battery-flashlight-radio.
@chuckdank38694 жыл бұрын
Rob, in 8 years on this channel, we have certainly come a long way with you since the Ukulele! Cheers & be well. ;-)
@trevorvanzuydam8115
4 жыл бұрын
I was thinking about the uke the other day. Did Rob ever finish it ?
@chuckdank3869
4 жыл бұрын
@@trevorvanzuydam8115 It might be in line for an electrical upgrade of some kind!
@trevorvanzuydam8115
4 жыл бұрын
@@chuckdank3869 would be fitting.
@ThinkingandTinkering
4 жыл бұрын
cheers mate
@ThinkingandTinkering
4 жыл бұрын
yes mate I did and played a tune for you lol - it's an old vid though
@il51diablo Жыл бұрын
This is a great Video Rob! On the other hand, I feel like I'm reviewing all the projects I've done over the past 10 years lol Continue like that your explanations and the ease that you have to do the projects is great. THANKS! :)
@tebbi674 жыл бұрын
wow exactly. . . you have to remember to regard the two coils as independent voltage sources. I'm learning here and am always delighted with this top-level motivation. thank you so much for that. THX for the vid!
@ThinkingandTinkering
4 жыл бұрын
cheers mate and glad you enjoyed it
@xxxblackvenomxxx2 жыл бұрын
I love your Videos and the joy you have doing stuff.
@javiervalles25442 жыл бұрын
Thank you for such an informative video, love your enthusiasm when the LEDs turn on!
@wdtripps65373 жыл бұрын
Wow, you are so knowledgeable, every video sparks ideas that lead to more questions. And I have seen you state we all learn here when someone is correct. Just an overall all great environment. Subbed for sure.
@jaet014 жыл бұрын
Great Video! This is the information I’ve been looking for, and you’ve presented it in such a very straight forward way. Your very good at that! Thank you!
@ThinkingandTinkering
4 жыл бұрын
cheers mate
@CraigLandsberg-lk1ep3 ай бұрын
To the Author, you are my favourite teacher online & I love how you use what is around you, even though most think it is ju nk, I 'save' everything hoping one day I can use it 😅 thanks heaps, always good to hear from a brit here in Australia 🌏 the 'colonies' lol 😅 keep up the good work
@stevetobias48904 жыл бұрын
Excellent video Rob. Got to love the simple capacitor and it's ability to store power. I love playing with stepper motors and like how simple you have explained everything
@ThinkingandTinkering
4 жыл бұрын
caps are just such strong things lol - and cheers mate
@stevetobias4890
4 жыл бұрын
@@ThinkingandTinkering I have a few 500F super caps I should get off my butt and use, I always have a lot of projects banked up waiting for me to finish.
@mikesmith21024 жыл бұрын
I make small table top concrete displays as a hobby. You could connect a water wheel to the stepper motor which would power a small water pump. You'd have to spin the wheel by hand a few times to charge the capacitors to power the pump to get the water moving over the wheel to get everything started. You'd do away with the electric cord or the battery for the pump. To stop the flow you just stop the wheel until the water stops. That has some real possibilities for some interesting dioramas and other displays.
@jakefriesenjake
Жыл бұрын
So you made a perpetual motion machine? Hot dang!
@cptrikester26714 жыл бұрын
This was good. I've been saving these types of motors from electronics for a while. Never knew what to do with them though. Will stop throwing away the capacitors now.
@ThinkingandTinkering
4 жыл бұрын
throwing away stuff! that sacrilege mate lol - I joke obviously - cheers
@cptrikester2671
4 жыл бұрын
@@ThinkingandTinkering If you saw my yard, you would know, I agree.
@CraigLandsberg-lk1ep
3 ай бұрын
You just said exactly what I have bin doing, I brought 4 large stepper motors with around 1.5 deg steps back in the late '80's and now I know what to do with them😅 thanks
@ericf.wolcott47164 жыл бұрын
So this is why I have been saving those 1980s hard drives
@ThinkingandTinkering
4 жыл бұрын
lol - that and the platters for a Tesla turbine I am sure lol
@hanslepoeter5167
4 жыл бұрын
an original st506 would have a stepper motor. That was my first harddrive and i still have it. Soon the head positioning motor was replaced by voice coils which are far superior
@aravinth007vt3 жыл бұрын
That smile at 13:09 is priceless :D nice video, i will try it as generator for sure.
@diegoburlandotheinformal12174 ай бұрын
I really appreciated your clear and insightful explanation. Many thanks.
@williamarmstrong71993 жыл бұрын
A brilliant description and love the circuit diagrams.
@darrellpidgeon64404 жыл бұрын
This is the best presentation yet involving the rectifier construction. I've taken apart some old CFL lamps to expose quite a few usable components. The rectifier is clearly visible on the circuit board. Unfortunately, the CFL is hard to come by these days. Lightbulbs (Edison base) now are all LED. Scavenging electronics has always been a hobby, but is limited by the surface mounted components in use today. When Radio Shack finally closed for good, it was a sad day. Well, they were going downhill anyway. At least components still exist online.
@ThinkingandTinkering
4 жыл бұрын
yeah SMDs are a pain - but eBay helps
@CraigLandsberg-lk1ep
3 ай бұрын
Dick Smith also went down in my country Australia 🌏 but now can get stuff online 😅
@CraigLandsberg-lk1ep3 ай бұрын
I 'love'this guy 😀 i have learnt soo much, i have a recent quote I want to share with everybody "knowledge cancels fear" thanks so much to the Author & I hope i can eventually get through all your videos 😅😅
@thesonnetist45833 жыл бұрын
Very informative and valuable, surprised to see thumbs down. Many thanks, keep on.
@hanslepoeter51674 жыл бұрын
4 wire types are common, 6 wire types are common ( simply have 2 taps in the center ), 5 wire is pretty rare and have the center taps connected together as in your diagram. ( center taps allow for cheap electronics as you don't need 2 full bridges and the dead time timing and stuff like that ) These are fun to play with. They also deliver phase information when used as generators. If you hook up a led wo diodes and turn the motor with led instead of the axis that's very visible and could be used for rotating displays and stuff. A wind turbine with adds would be fun. These are also pretty good breaks. Tie all wires together and then turn the axis .. if you can ...
@CraigLandsberg-lk1ep
3 ай бұрын
I have a 6 wire stepper motor, can you explain anything you can to me about it? Would appreciate any information 😅 thanks
@Jermeister2 жыл бұрын
I love the teaching style! Clear to follow and understand the basic principles as well as the build, so I went ahead and made my own set too! What sort of amperage and wattage were you getting from yours? My current readings ended up being a dismal 0.02A, but the low rpm-high voltage output (>7V with finger turning) was really neat to play with! Hooked mine up to a voltage regulator to charge a powerbank; not sure how many hours that's going to take though!
@ladycharlesmusic2 жыл бұрын
Just found your channel and love it - hoping I can salvage from some of my broken electronics to make some crank chargers for an emergency or just on the go!
@danieltommila4603 Жыл бұрын
Incredible Channel you have. I have learned so much. Also putting these I learned to use.😃
@kevinbowker2385 Жыл бұрын
Very informative and entertaining. Thank you for sharing!
@freesoul93243 жыл бұрын
THANK YOU for sharing this awesome info.
@Jimpandude Жыл бұрын
Very helpful! Thank you for this video 🙏❤️
@amokutoheti599 Жыл бұрын
❤ The best job and the best explanation
@ricmucha90964 ай бұрын
That is everything I need thank you so much now to find and smash some printers lol
@peterclancy36533 жыл бұрын
Bloody marvellous!!! I have heaps of stepper motors and use arduino electronics to operate them and have always been fascinated by the control that one can have with them. Thanks for the possible rechargeable torch?
@dallasmoss14284 жыл бұрын
Something like that is what I was looking for to put on my windmills in the yard
@ThinkingandTinkering
4 жыл бұрын
awesome mate
@nicholashullander7211
3 жыл бұрын
Try a hover board drive motor
@Yadilea2 жыл бұрын
Very nicely explained. Thank you kindly!
@Superimperator3 жыл бұрын
absolute exact what i searching 4 :) big thanks! :)
@grahamh49604 жыл бұрын
Excellent, thanks.👏👏👏👏 I have some stepper motors from past 3d printers so they will be used in the near future. 👍👍👍👍
@ThinkingandTinkering
4 жыл бұрын
awesome mate
@tinkmarshino4 жыл бұрын
Outstanding Rob dang this is wonderful.. (especially there little spindle motors from the cd cases I was asking about) I have a few stepper motors around to play with.. I, like you, hate to throw things away if there are good parts to it.. I always take them apart and if I do not know what to do with the parts at the moment I save them for later.. You have given me many great little projects for the winter time (when I am stuck in the house) this is gonna be a great winter this year!!! Thanks ever so much my man.. I get so bored in the winter I started to play with electronics last year (it is hard to learn new tricks at 68.. I never used to be this way..) This winter will be full of fun.. thanks to you.. carry on! I appreciate all you do..
@ThinkingandTinkering
4 жыл бұрын
awesome mate - so I can expect a few vids from you come winter?
@tinkmarshino
4 жыл бұрын
@@ThinkingandTinkering sure.. you think I should? well maybe just for you to peruse and critiques maybe.. I just have no idea how to do a video very well... I have one on my page but it was one of my home I made so my friends over seas could see what I have done to it.. If you watch it don't mind my grunting and groaning.. I was in a bit of pain that morning while I filmed it.. Thanks for everything Rob.. your a good man.. and if I ever get to england I will look your up..
@ThinkingandTinkering
4 жыл бұрын
@@tinkmarshino for sure mate - I would love to see them and look at my first videos - they were rubbish! lol - and you are more than welcome to visit mate
@tinkmarshino
4 жыл бұрын
@@ThinkingandTinkering Thanks Rob.. I appreciate that!
@ThinkingandTinkering
4 жыл бұрын
@@tinkmarshino no worries mate
@G-REV_CHUCK4 жыл бұрын
Hey Robert, Here's an Idea for a video. Show The Electronics bits and pieces that you use to build your circuits for making generators usable for everyday projects. If you haven't already made a video of that. Kinda new to the channel. But am loving the content. Thanks for the inspiration!
@truthseeker39072 жыл бұрын
Thank You Robert Murray Smith!👍
@ronaldschild1573 жыл бұрын
This is very well done. The phrasing is simple and elegant and the video shots of the hands-on work is likewise. One question I have is about the units in your capacitors you have chosen: Is it 500 farads or 500 microfarads? I know even a one farad audio capacitor is about the size of child's shoe, so I'm left wondering. Nonetheless, thank you so much for producing this video. I feel like I was invited into your shop to get a personal session of instruction.
@sclint31563 жыл бұрын
I just fpind yoir members are amazomg, so o wrote a question below cant wait for yoir i fo to get this project rocking. mamy thanks.
@barbufodor11864 жыл бұрын
Excellent content as usual!
@sierraecho8849 ай бұрын
Exactly what I was looking for. I want to make a small stirling engine with a small generator with an output of 2W-15W something like that. Just a small demonstrator for fun.
@Plaasbakkie4 жыл бұрын
Hi Rob this video is personal to me because in the previous video I asked exactly about this. Topic. Another motor to look at is maybe the brushless motors from the new type electric drills and also used in electric radio controlled cars. Basically a mini 3phase motor.
@ThinkingandTinkering
4 жыл бұрын
they are all built to the same basic design mate - if you can do a pc fan motor you can do pretty much all BLDC motors including the ones in drills. We did a conversion of a PC fan just apply that
@CraigLandsberg-lk1ep
3 ай бұрын
I also want to know about using a brushless drill motor for this 😅
@markmaker24884 жыл бұрын
An easy way to find the correct wire pairs without a multimeter is by simply joining two wires together and turning the spindle. If you feel resistance you have found your pair.
@ThinkingandTinkering
4 жыл бұрын
you can - unless it is a small motor in which case you are not going to feel it mate - but nice post and thanks for the tip
@cecilcooper62104 жыл бұрын
Thanks for simplifying that. Very useful.
@ThinkingandTinkering
4 жыл бұрын
Glad it was helpful!
@simonleuenberger4657 Жыл бұрын
Hello Rob, great videos! I have to admit, I really got hooked up with the idea of building my own wind generator. Not for getting my whole household running of course, but for the experimenting around for fun. Idea is to have a couple of ugrinsky elements stacked on one axis with a bit offset (don't have a 3d printer 😅). A stepper motor would be my generator. Now, what puzzles me is the question if I risk burning the generator at better wind or what to keep in mind. Should I better go with the Thunderbolt generator concept and what wire diameter is good if doing so? Kind regards from Switzerland. Keep going!
@electricsheep2305 Жыл бұрын
I just found your videos, thank you this is great content!
@ThinkingandTinkering
Жыл бұрын
Glad you like them!
@videomentaryproductionschannel4 жыл бұрын
As usual Robert excellent video, keep the coming
@ThinkingandTinkering
4 жыл бұрын
cheers mate
@russbilzing53484 жыл бұрын
Thank you for this, it makes things so much more clearly understandable, the unmistakable sign of a proper teacher/tutor. I have a 12 volt DC stepper motor about a foot long and 6 or so inches in diameter that I hoped to utilize as a source of motive power. I haven't seen it in over a year, or I would know the amperage, wattage, maker etc. Can this simple circuit be of use in pursuit of my quest? Is it feasible, on the whole, to hope that this motor might serve my purpose, to propel a trike of the Morgan variety, lightly laden? I am off in a day or so to retrieve it and thought I ought to ask. By the time you answer, I should know the proper answers. In either case, thank you.
@NnaemekaOkonkwo-fq2yu4 ай бұрын
Well explained.great contents ❤
@shagui2 жыл бұрын
Very nice video and very good explanation!!!
@tonysmith87474 жыл бұрын
Brilliant Rob !!
@ThinkingandTinkering
4 жыл бұрын
cheers mate
@kolinevans91274 жыл бұрын
Seems like a handy little hand crank generator I might be able to use something-like this thanks for sharing, if you config a Zener diode at about 5 / 6 v across the C storage in reverse bias it will regulate the V to that V and you will have a rudimentary phone charger 6v~ As long as the Zener wattage is not exceeded but I think it would be ok , you could parallel the Zener for more wattage. Regards
@ThinkingandTinkering
4 жыл бұрын
cheers mate
@OyvindSOyvindS4 жыл бұрын
Thank you very much!!!
@josephtuntepe24433 жыл бұрын
Thanks a lot, you were very helpful
@nw76963 жыл бұрын
I just found out that the new GM pickup trucks use stepper motors for their cooling fans, looks promising!
@JonnyDeRico4 жыл бұрын
I like it. Consider using schottky diodes for lower voltage drop and more current.
@ThinkingandTinkering
4 жыл бұрын
for sure mate - I am likely to do a vid on the misfit based rectifier - almost zero drop
@ARandomTroll
4 жыл бұрын
@@ThinkingandTinkering please do- i want a bigger electrolysis PSU.
@hanslepoeter5167
4 жыл бұрын
@@ThinkingandTinkering I googled that but cannot find it. I suppose thats about using mosfets for controlled recification. I never found how to do that actually. A vid would be nice ....
@AdelsonDePaulo
3 жыл бұрын
I did something like that. But I noticed that my generator would generate for both sides. Is that okay or have I made a mistake with the coils wire?
@JonnyDeRico
3 жыл бұрын
@@AdelsonDePaulo what do you mean with both sides?
@jaminoes_4 жыл бұрын
Those are the fingernails of a maker. :-) I love these videos.
@ThinkingandTinkering
4 жыл бұрын
lol - yeah - hard to keep them clean lol
@overunityresearchchannel4 жыл бұрын
Output is very impressive low rpm Great video Robert thanks man also did you know that you can use a Stepper Motor as a Bedini Motor you can use the same one you showed in this video all you need is to make the bedini ssg circuit then hook the stepper motor to the circuit 2 wires will be the trigger and the other 2 will be the power wires the power wires will be the coil with the most resistance and the trigger wires will be the ones with the lowest resistance the orientation of the wires don't matter for each coil but yes the 2 wires that go to the trigger have to go to the trigger what I'm saying is the start and the end of the coil doesn't matter just wire the 2 triggers to the trigger on the circuit and 2 power wires to power wire on the circuit and the the circuit has 2 posatives and 2 negatives so 1 set for the run battery and other for charging battery once it's hooked up just spin the stepper motor by hand give it a quick turn left if it doesn't start spinning then spin it right and you will see it spin it will hum and vibrate a bit on the table also use the potentiometer to a just the charing rate and speed and amp draw on the run battery also you can get it to go into self ossilation mode where it doesn't spin but vibrates and hums and will still charge would be awesome to see you make a video on this think it's very useful you don't have to worry about winding coils and making rotors just make the ssg circuit and get a stepper motor and 2 battery's and your good to go Cheers Mate
@ThinkingandTinkering
4 жыл бұрын
nice one - cheers mate
@clint9344
4 жыл бұрын
Ahh Thanks for the idea Brandon never thought of it from that perspective. Interesting to say the least will have to experiment with this. God Speed
@FPChris3 жыл бұрын
Outstanding.
@2Langdon4 жыл бұрын
Excellent, very useful again. It was pitched just right for me and my current level of understanding. ( See what I did there? Groan)
@DylanDavidVindasLopez2 жыл бұрын
Thank you!!
@JustFun-iz9rf4 жыл бұрын
Great video thank you
@ThinkingandTinkering
4 жыл бұрын
Glad you enjoyed it
@youtubeworkshop3174 Жыл бұрын
Thank you too bro.. for detailed video
@victorreppeto70504 жыл бұрын
I would like to see a simple design for an axial generator attached to a reciprocating stirling engine you featured a while back.
@ThinkingandTinkering
4 жыл бұрын
work on it!
@jean-mariemuga28193 жыл бұрын
Thank you sir!!
@littleworkshopofhorrors23954 жыл бұрын
He's enjoying his job again.😉 👍👍👍
@ThinkingandTinkering
4 жыл бұрын
I certainly am lol
@jpb6 Жыл бұрын
13:10 haha i love it, i actually got the same reaction 😂 Thank you very mu h that really helps me for a University project :)
@colouroboros99934 жыл бұрын
really awesome!
@ThinkingandTinkering
4 жыл бұрын
Thank you! Cheers!
@arjunanil74412 жыл бұрын
Thanks Sir ..... Thank you very much...😍😍😍😍😍😍
@3brosh3 жыл бұрын
i understand stepper to diode to capacitor but how does it work after that? I want to use the stepper motor to charge a battery. What does the capacitor get connected to after? A charge controller? I would love a video of the next steps after what was said in this video. Example. i want to charge a 48v E-bike Lithium Ion Battery using a stepper motor as a windmill. I love the idea of the capacitor holding the charge and sending a continuous current even if the windmill isn't in motion. I am a visually learner and these videos are extremely helpful! I would appreciate any help!!!!
@brainretardant4 жыл бұрын
Brilliant!
@ThinkingandTinkering
4 жыл бұрын
cheers mate
@Aethalops4 жыл бұрын
Thanks so much! Super useful and inspiring. As a novice, when thinking about applications, I wonder about how to get a feel for dangers and limitations of this sort of project... e.g., Is there any danger of damaging the stepper motor by turning it too fast?
@ThinkingandTinkering
4 жыл бұрын
It's why I do so many small experiments mate - you get a feel but at low cost. Some folks complain I don't build enough big things - if I did that it would bankcropt me - do a lot of small - get a feel and then do a big
@solarhope4 жыл бұрын
Great explanation and drawings Rob :-) If you are short of components, maybe you could wire the two coils in series or parallel before you connect to the bridge circuit. You would then only need 4 diodes and 1 capacitor.
@GRBtutorials
4 жыл бұрын
But the coils are 90° out of phase, so connecting them in parallel would be quite inefficient and could potentially damage the motor. Connecting them in series could work, though.
@solarhope
4 жыл бұрын
@@GRBtutorials Cheers for that, must confess I had not thought it through, got it half right :-)
@ThinkingandTinkering
4 жыл бұрын
you could do that mate - but often the coils are of different size and they are out of phase so there would be a bit of 'fighting' going on if you did that.
@solarhope
4 жыл бұрын
@@ThinkingandTinkering I should have known you would not be using twice the bits for nowt :-)
@onemanriflemaker38734 жыл бұрын
Oh yes. You got to stepper motors that’s properly awesome. These things are proper cheap. A CVT is a easy 3D printer job. This is proper exciting.
@ThinkingandTinkering
4 жыл бұрын
they are mate - that little one I showed with the gears is only £3
@thomasjehnkins19863 жыл бұрын
OMG thank you!... I have always wondered about making bridge rectifiers! Couple of questions... are there any sources of bridge rectifiers (or parts) in PC components (or even ready made) I could scavenge? AND Could I use a few (or many) super capacitors from the microwave I disassembled to get some storage to run 30 - 60 meters of 50/50 smd led strip lights?
@smartypants5036 Жыл бұрын
I am sure that the 5 wire motor is a cheap way to allow micro stepping so you can pulse half a coil at a time and use a micro controller to control the pulsing sequence. I assume that the six wire motors are a similar thing. Thanks for your great videos. I would like to try a wind wall. It is not possible where I live to put up a turbine on a tower without the permission of all the neighbors.
@michaellivsey72263 жыл бұрын
Thank you so much....now I know how to wire it....I've been trying to find I formation on it, but it was way too confusing
@cyrus36964 жыл бұрын
ty very helpful
@ThinkingandTinkering
4 жыл бұрын
Glad it helped
@Electronzap4 жыл бұрын
Pretty cool stuff :)
@ThinkingandTinkering
4 жыл бұрын
Thanks mate
@lv_woodturner38994 жыл бұрын
I enjoyed the video, thanks. I have 3 NEMA 17 stepper motors on my 3D printer. It is easy to generate a back EMF when moving the printer plate. I have to be careful to move slowly so I do not zap the electronics. I have seen the printer display light up. Not good. Testing for the wire pair which is a coil is easy to do without a multi-meter. Touch two wires together and try turning the shaft. If the wires are a coil pair you will feel resistance to the shaft turning. The splined belt comes in various pitches and widths. The belt should have the type, e.g., GT2, GT3, etc., but the pinion gear will not have a label, so unless you have purchased a specific pinion gear, it will be important to check the pitch on the pinion to ensure it matches the belt. GT2 and MXL pitches are very close but not interchangeable. My 3D printer is using GT2, but my latest project is an electronic step indexer for the wood lathe and it is using MXL belt, so I have to be careful not to interchange anything. Dave.
@ThinkingandTinkering
4 жыл бұрын
nice info mate - cheers
@jeffmastin4 жыл бұрын
Look for outdated reprographic machines that are being replaced. On Craigslist I picked one up for free and another for 25 bucks US. they are loaded with high quality steppers and driver circuits not even close to their duty limit as well as other valuable components like capacitors and gear reduction motors. I probably harvested 20-30 steppers from these two
@ThinkingandTinkering
4 жыл бұрын
that is a nice post post mate - thanks for the info
@CDinkle4 жыл бұрын
Awesome video, I have a few large steppers laying around that now I know what to do with! What kind of amperage are you seeing with this set up?
@ThinkingandTinkering
4 жыл бұрын
not much mate - I was turning it by hand! Amp out put is going to be dependant on your input mate
@karlmavadia76634 ай бұрын
Thank you Robert, I just logged into KZread after a very longtime so I could send a thumbs up, appreciation & subscribe! Have a question: What Step a motor or other technical spec & considerations would you recommend for a DIY hand crank mobile phone charger to actually charge the phone without damaging it?? Cheers, 🙂
@DavidHoegen4 жыл бұрын
I had a LG washer. It motor was a stepper motor. Realy big. If you turned it by hand it would power the light and buttons. Realy cool
@ThinkingandTinkering
4 жыл бұрын
LG - must look out for one
@hugoboy9713 жыл бұрын
Great video! good thing i find this as i am planning on doing a wind turbine project! Just a quick question, does anyone know what was the voltage rating of the stepper motor used here? a help would be greatly appreciated! :D
@kenvoo73033 жыл бұрын
Nice to watch your vid... Can i ask ? What type motor has least friction when generating output power ? Is motor with gearbox harder to turn on shaft ?
@navalkishoresingal2 жыл бұрын
Hello Sir, At first thanks for sharing the wonderful information in the best easy way. I have few questions in my mind taking "Stepper Motors", hope you could answer them. Thanks in advance. Q1. According to you, which motor is best to generator electricity, and why? Options: A. Brushed DC Motor B. BLDC Motor C. Stepper Motor Q2. Referencing video, if I choose "Stepper Motor" as a Generator then which one to choose and on what parameters? We have, Stepper Motors with many different specifications such as a. Unipolar and Bipolar What I have learnt and understood watching videos on KZread (I maybe wrong, maybe right, please correct me if it goes wrong) is that, Unipolar is easy to use and works faster than Bipolar. Secondly, we don't need to reverse the rotational direction in the Generator, so we don't need "Bipolar". So, we should use Unipolar in Power generation. (Please clarify) - Which one to choose and what are the advantages and disadvantages? b. Low / High Torque Second factor that I get to know about is the "Torque". In my learning, torque is the rotational force that is required to push or pull something. But in our case of power generation, we are not going to use Stepper Motor as motor but as generator which needs rotation at a speed to generate some voltage. We are not pushing or pulling anything. So, we should not consider or least consider Torque. Low Torque - High Speed (Please clarify) - What motor torque should be consider in Stepper Motor as generator? - Is least torque motor best suitable for power generation? c. Low/ High Input Voltage There are different input voltages available such as (12V, 24V, 48V, etc) according to different sizes and different torques. - Do they have any relation to the output voltage of the Stepper Motor as generator? - Which is best suitable voltage stepper motor to choose to work as generator? d. RPM (Speed) Get to know, Stepper motors have different RPM (10000, 6000, 4000, 3000, 2000, 1500, 1000 or lesser) Smaller Motors have Less Torque but High Speed As the size increases Motors have higher Torque and Lesser Speed -Is it correct, that, more the speed more the voltage we would get? (Please clarify) -What is the ideal speed or RPM that we require to generate the desired or correct output (voltage) for power generation? e. Steps (Less / 200 / 400 / More) As per my information, Steps are only required for the accuracy to work. More Steps gives More Accuracy and Precision - Do "Steps" play a role in power generation which I don't think so, please clarify? f. Single / Double Shaft - Do we have advantage of double shaft motor instead of single, in case, if we put 2 rotors to rotate the shaft of the "Stepper Motor i.e Generator) for more smooth operation and speed? (Please comment and clarify) g. Geared / Non Geared As per my information, gears gives more or high torque. - Do we any advantage of geared stepper motor in power generation which I don't think so? (Please comment and share your views) What all factors are important and must be considered choosing stepper motor as generator? Also consider, other factor that I have missed which should be considered choosing "Stepper Motor" as Generator. It would be really helpful, if you would share your views and comment or prepare a video considering the above points. Thank you once again for sharing the informational video and look forward more similar videos from you. Thanks
@ArnookieVR
2 жыл бұрын
Stepper motors are the obvious choice. They are easy to wire and produce a good output. DC motors have brushe that degrade pretty quickly.
@navalkishoresingal
2 жыл бұрын
@@ArnookieVR Thankyou for your response, what about Brushless DC motors. Can you respond to any of the queries above for better understanding.
@ArnookieVR
2 жыл бұрын
@@navalkishoresingal I find stepper motors are better for hobby use overall. They are easy to connect and produce a good voltage evan at low speeds. This makes them ideal for DIY wind turbines & hand cranked generators. You would need to use a rectifier and capacitor on the output to get a nice stable DC output voltage. You can also use a car radiator fan for a super easy wind turbine. But you would need to increase the fan blades length. 😉
@ArnookieVR
2 жыл бұрын
Stepper motors are rarely rated on voltage. This is because of the nature stepper motors work by. Steppers are usually run on a low voltage. A NEMA 17 stepper would normally be rated 12 to 24v. But would normally be driven by 2v or even less ie when used on a 3d printer.
@DanaGould04 жыл бұрын
You should see if you can find a broken hoverboard and salvage the wheel motors from it. There are a couple of youtube videos from 'DIY King' using one in a horizontal and vertical wind turbine. The horizontal turbine seemed to work well, but I think the vertical turbine needed to be geared up for better performance.
@ThinkingandTinkering
4 жыл бұрын
cheers mate - I tend to use what I stumble over so if one crosses my path you cane sure I'll use it lol
Пікірлер: 344
Best video ever explaining this subject. Totally no nonsense and easy to understand. Bravo!
Man where were you 15 years ago when i had to learn everything the Hardway!!! Your videos are Brilliant, straight to the point, and very easy to understand* Thank you professor 👍 😀
@ThinkingandTinkering
4 жыл бұрын
cheers mate
You sir are a treasure! Just recently found your videos and am on a binge watching kick with them! Thank you so much for doing what you are doing!
I watched this video, although I knew already everything you were talking about. Your voice is so pleasant. One thing I would like to add to your explanation on how to find the two cables of one coil. There is a method to find the corresponding wires without any measuring instrument except your hand. Just connect two wires and try to turn the motor by hand. If it is hard to turn, you found the wires of one coil. Easy to do, but perhaps a bit more difficult to explain why this works. And a bit funny, because it already has to do with power generation. :-)
@kevinpersinger7957
Жыл бұрын
Thanks for the tip. Im gonna try that for isolating coils. I already identified it with a meter, but I don't always have that available(because i forget to plan sometimes). Good idea for a minimal survival if you need to generate power possibly too!
@CraigLandsberg-lk1ep
3 ай бұрын
Really glad to hear your comment 😅 I bought a heap of large stepper motors back in the late '80's and now I know how to use them, thanks for your comment 😅😅
@jonttan03
2 ай бұрын
Or just test it with your tongue 🙃
I'd recommend parallel wiring for small wind turbines; with the series config you'll reach the target voltage at a lower speed, but as the turbine efficiency goes up with tip speed ratio (how fast it rotates relative to the wind speed) and small wind turbines have a tiny radius so a high RPM is needed for a high tip speed, you really want this thing to spin fast. Therefore it's probably a good idea to try and wire it up in parallel so that the target voltage is reached at a more optimal RPM. If you don't reach the target voltage this way, you can always decide to go back to series. Very nice video btw!
@ThinkingandTinkering
4 жыл бұрын
cheers mate
You can figure out the wiring without a meter by shorting the wires and trying to turn the spindle/shaft. When the resistance increases with two wires shorted, you know they're both wires of one coil.
I've been looking for a while to find a good video with someone actually explaining things in detail. All I was finding were two hands and elevator music with bad video quality to go by until now, cheers mate 👍 This helped loads, subbed!
Love it. I've seen people use LEDs for their rectifiers, as those were the only diodes they had sitting around. Thought that was ingenious. Cheers!
@Plaasbakkie
4 жыл бұрын
I have done this aswell
@ThinkingandTinkering
4 жыл бұрын
it works just fine mate - most folks think a LED is for one thing only - but it is still a diode
@thesonnetist4583
3 жыл бұрын
Glad to know that. Thanks
@lucasvanhamburg4937
3 жыл бұрын
would't this heavily limit the current?
Robert, I caught you just in time. Your "learn away skills" must be something you have had as a profession or something, calm voice, perfect dictation... And best of all, at least for me, perfect topics for Your videos, I'm learning A LOT. You are already successfull, but the sky is the limit for you're YT success. Greatings from Norway.
Keep up the fascinating work you are showing us. You obviously stimulate free thinking, and for that I am very grateful.
@DimitriPappas
4 жыл бұрын
Agreed. This channel is wonderful
@ThinkingandTinkering
4 жыл бұрын
Wow, thank you mate
I used a mid drive 250watt bldc electric bike motor and used my bike to run my 50 watt tv with super capacitors . Worked great . It was the best energy harvester i made and i think the motor was perfect as it did not require much rpm to create the necessary 12 volts for the screen . It seemed to be around 100 watt i was producing for about 10 min and got 20 min telly time ! The key to its effeciency was using a 48 v ebike motor as the rpm could be low to get 12 volts out !
@ThinkingandTinkering
4 жыл бұрын
that is awesome mate - thanks for sharing
@CraigLandsberg-lk1ep
3 ай бұрын
Can I ask how you regulated it to provide the exact voltage? 😅 thanks
You never ever EVER cease to amaze! Thank you for taking the time to share your knowledge. I have a largish stepper motor from a surface sander. My younger brother overtaxed it and I replaced it from the nearby DeWalt store. I kept the old one, and now I know why.
@ThinkingandTinkering
4 жыл бұрын
awesome mate - I did't know DeWalt used them
I'm learning more practical knowledge from you than 2years of military electronics training. I should have gone for fixing the motors instead of the weapons systems.
Great Rob, thanks! In theory rectifiers are dead easy to make, and I also know the different kinds with their pros and cons. But despite, until this day I didn't make a single one. Thanks to your reminder and your step by step tutorial I will do so and also go and repair my somehow failed crank-generator-battery-flashlight-radio.
Rob, in 8 years on this channel, we have certainly come a long way with you since the Ukulele! Cheers & be well. ;-)
@trevorvanzuydam8115
4 жыл бұрын
I was thinking about the uke the other day. Did Rob ever finish it ?
@chuckdank3869
4 жыл бұрын
@@trevorvanzuydam8115 It might be in line for an electrical upgrade of some kind!
@trevorvanzuydam8115
4 жыл бұрын
@@chuckdank3869 would be fitting.
@ThinkingandTinkering
4 жыл бұрын
cheers mate
@ThinkingandTinkering
4 жыл бұрын
yes mate I did and played a tune for you lol - it's an old vid though
This is a great Video Rob! On the other hand, I feel like I'm reviewing all the projects I've done over the past 10 years lol Continue like that your explanations and the ease that you have to do the projects is great. THANKS! :)
wow exactly. . . you have to remember to regard the two coils as independent voltage sources. I'm learning here and am always delighted with this top-level motivation. thank you so much for that. THX for the vid!
@ThinkingandTinkering
4 жыл бұрын
cheers mate and glad you enjoyed it
I love your Videos and the joy you have doing stuff.
Thank you for such an informative video, love your enthusiasm when the LEDs turn on!
Wow, you are so knowledgeable, every video sparks ideas that lead to more questions. And I have seen you state we all learn here when someone is correct. Just an overall all great environment. Subbed for sure.
Great Video! This is the information I’ve been looking for, and you’ve presented it in such a very straight forward way. Your very good at that! Thank you!
@ThinkingandTinkering
4 жыл бұрын
cheers mate
To the Author, you are my favourite teacher online & I love how you use what is around you, even though most think it is ju nk, I 'save' everything hoping one day I can use it 😅 thanks heaps, always good to hear from a brit here in Australia 🌏 the 'colonies' lol 😅 keep up the good work
Excellent video Rob. Got to love the simple capacitor and it's ability to store power. I love playing with stepper motors and like how simple you have explained everything
@ThinkingandTinkering
4 жыл бұрын
caps are just such strong things lol - and cheers mate
@stevetobias4890
4 жыл бұрын
@@ThinkingandTinkering I have a few 500F super caps I should get off my butt and use, I always have a lot of projects banked up waiting for me to finish.
I make small table top concrete displays as a hobby. You could connect a water wheel to the stepper motor which would power a small water pump. You'd have to spin the wheel by hand a few times to charge the capacitors to power the pump to get the water moving over the wheel to get everything started. You'd do away with the electric cord or the battery for the pump. To stop the flow you just stop the wheel until the water stops. That has some real possibilities for some interesting dioramas and other displays.
@jakefriesenjake
Жыл бұрын
So you made a perpetual motion machine? Hot dang!
This was good. I've been saving these types of motors from electronics for a while. Never knew what to do with them though. Will stop throwing away the capacitors now.
@ThinkingandTinkering
4 жыл бұрын
throwing away stuff! that sacrilege mate lol - I joke obviously - cheers
@cptrikester2671
4 жыл бұрын
@@ThinkingandTinkering If you saw my yard, you would know, I agree.
@CraigLandsberg-lk1ep
3 ай бұрын
You just said exactly what I have bin doing, I brought 4 large stepper motors with around 1.5 deg steps back in the late '80's and now I know what to do with them😅 thanks
So this is why I have been saving those 1980s hard drives
@ThinkingandTinkering
4 жыл бұрын
lol - that and the platters for a Tesla turbine I am sure lol
@hanslepoeter5167
4 жыл бұрын
an original st506 would have a stepper motor. That was my first harddrive and i still have it. Soon the head positioning motor was replaced by voice coils which are far superior
That smile at 13:09 is priceless :D nice video, i will try it as generator for sure.
I really appreciated your clear and insightful explanation. Many thanks.
A brilliant description and love the circuit diagrams.
This is the best presentation yet involving the rectifier construction. I've taken apart some old CFL lamps to expose quite a few usable components. The rectifier is clearly visible on the circuit board. Unfortunately, the CFL is hard to come by these days. Lightbulbs (Edison base) now are all LED. Scavenging electronics has always been a hobby, but is limited by the surface mounted components in use today. When Radio Shack finally closed for good, it was a sad day. Well, they were going downhill anyway. At least components still exist online.
@ThinkingandTinkering
4 жыл бұрын
yeah SMDs are a pain - but eBay helps
@CraigLandsberg-lk1ep
3 ай бұрын
Dick Smith also went down in my country Australia 🌏 but now can get stuff online 😅
I 'love'this guy 😀 i have learnt soo much, i have a recent quote I want to share with everybody "knowledge cancels fear" thanks so much to the Author & I hope i can eventually get through all your videos 😅😅
Very informative and valuable, surprised to see thumbs down. Many thanks, keep on.
4 wire types are common, 6 wire types are common ( simply have 2 taps in the center ), 5 wire is pretty rare and have the center taps connected together as in your diagram. ( center taps allow for cheap electronics as you don't need 2 full bridges and the dead time timing and stuff like that ) These are fun to play with. They also deliver phase information when used as generators. If you hook up a led wo diodes and turn the motor with led instead of the axis that's very visible and could be used for rotating displays and stuff. A wind turbine with adds would be fun. These are also pretty good breaks. Tie all wires together and then turn the axis .. if you can ...
@CraigLandsberg-lk1ep
3 ай бұрын
I have a 6 wire stepper motor, can you explain anything you can to me about it? Would appreciate any information 😅 thanks
I love the teaching style! Clear to follow and understand the basic principles as well as the build, so I went ahead and made my own set too! What sort of amperage and wattage were you getting from yours? My current readings ended up being a dismal 0.02A, but the low rpm-high voltage output (>7V with finger turning) was really neat to play with! Hooked mine up to a voltage regulator to charge a powerbank; not sure how many hours that's going to take though!
Just found your channel and love it - hoping I can salvage from some of my broken electronics to make some crank chargers for an emergency or just on the go!
Incredible Channel you have. I have learned so much. Also putting these I learned to use.😃
Very informative and entertaining. Thank you for sharing!
THANK YOU for sharing this awesome info.
Very helpful! Thank you for this video 🙏❤️
❤ The best job and the best explanation
That is everything I need thank you so much now to find and smash some printers lol
Bloody marvellous!!! I have heaps of stepper motors and use arduino electronics to operate them and have always been fascinated by the control that one can have with them. Thanks for the possible rechargeable torch?
Something like that is what I was looking for to put on my windmills in the yard
@ThinkingandTinkering
4 жыл бұрын
awesome mate
@nicholashullander7211
3 жыл бұрын
Try a hover board drive motor
Very nicely explained. Thank you kindly!
absolute exact what i searching 4 :) big thanks! :)
Excellent, thanks.👏👏👏👏 I have some stepper motors from past 3d printers so they will be used in the near future. 👍👍👍👍
@ThinkingandTinkering
4 жыл бұрын
awesome mate
Outstanding Rob dang this is wonderful.. (especially there little spindle motors from the cd cases I was asking about) I have a few stepper motors around to play with.. I, like you, hate to throw things away if there are good parts to it.. I always take them apart and if I do not know what to do with the parts at the moment I save them for later.. You have given me many great little projects for the winter time (when I am stuck in the house) this is gonna be a great winter this year!!! Thanks ever so much my man.. I get so bored in the winter I started to play with electronics last year (it is hard to learn new tricks at 68.. I never used to be this way..) This winter will be full of fun.. thanks to you.. carry on! I appreciate all you do..
@ThinkingandTinkering
4 жыл бұрын
awesome mate - so I can expect a few vids from you come winter?
@tinkmarshino
4 жыл бұрын
@@ThinkingandTinkering sure.. you think I should? well maybe just for you to peruse and critiques maybe.. I just have no idea how to do a video very well... I have one on my page but it was one of my home I made so my friends over seas could see what I have done to it.. If you watch it don't mind my grunting and groaning.. I was in a bit of pain that morning while I filmed it.. Thanks for everything Rob.. your a good man.. and if I ever get to england I will look your up..
@ThinkingandTinkering
4 жыл бұрын
@@tinkmarshino for sure mate - I would love to see them and look at my first videos - they were rubbish! lol - and you are more than welcome to visit mate
@tinkmarshino
4 жыл бұрын
@@ThinkingandTinkering Thanks Rob.. I appreciate that!
@ThinkingandTinkering
4 жыл бұрын
@@tinkmarshino no worries mate
Hey Robert, Here's an Idea for a video. Show The Electronics bits and pieces that you use to build your circuits for making generators usable for everyday projects. If you haven't already made a video of that. Kinda new to the channel. But am loving the content. Thanks for the inspiration!
Thank You Robert Murray Smith!👍
This is very well done. The phrasing is simple and elegant and the video shots of the hands-on work is likewise. One question I have is about the units in your capacitors you have chosen: Is it 500 farads or 500 microfarads? I know even a one farad audio capacitor is about the size of child's shoe, so I'm left wondering. Nonetheless, thank you so much for producing this video. I feel like I was invited into your shop to get a personal session of instruction.
I just fpind yoir members are amazomg, so o wrote a question below cant wait for yoir i fo to get this project rocking. mamy thanks.
Excellent content as usual!
Exactly what I was looking for. I want to make a small stirling engine with a small generator with an output of 2W-15W something like that. Just a small demonstrator for fun.
Hi Rob this video is personal to me because in the previous video I asked exactly about this. Topic. Another motor to look at is maybe the brushless motors from the new type electric drills and also used in electric radio controlled cars. Basically a mini 3phase motor.
@ThinkingandTinkering
4 жыл бұрын
they are all built to the same basic design mate - if you can do a pc fan motor you can do pretty much all BLDC motors including the ones in drills. We did a conversion of a PC fan just apply that
@CraigLandsberg-lk1ep
3 ай бұрын
I also want to know about using a brushless drill motor for this 😅
An easy way to find the correct wire pairs without a multimeter is by simply joining two wires together and turning the spindle. If you feel resistance you have found your pair.
@ThinkingandTinkering
4 жыл бұрын
you can - unless it is a small motor in which case you are not going to feel it mate - but nice post and thanks for the tip
Thanks for simplifying that. Very useful.
@ThinkingandTinkering
4 жыл бұрын
Glad it was helpful!
Hello Rob, great videos! I have to admit, I really got hooked up with the idea of building my own wind generator. Not for getting my whole household running of course, but for the experimenting around for fun. Idea is to have a couple of ugrinsky elements stacked on one axis with a bit offset (don't have a 3d printer 😅). A stepper motor would be my generator. Now, what puzzles me is the question if I risk burning the generator at better wind or what to keep in mind. Should I better go with the Thunderbolt generator concept and what wire diameter is good if doing so? Kind regards from Switzerland. Keep going!
I just found your videos, thank you this is great content!
@ThinkingandTinkering
Жыл бұрын
Glad you like them!
As usual Robert excellent video, keep the coming
@ThinkingandTinkering
4 жыл бұрын
cheers mate
Thank you for this, it makes things so much more clearly understandable, the unmistakable sign of a proper teacher/tutor. I have a 12 volt DC stepper motor about a foot long and 6 or so inches in diameter that I hoped to utilize as a source of motive power. I haven't seen it in over a year, or I would know the amperage, wattage, maker etc. Can this simple circuit be of use in pursuit of my quest? Is it feasible, on the whole, to hope that this motor might serve my purpose, to propel a trike of the Morgan variety, lightly laden? I am off in a day or so to retrieve it and thought I ought to ask. By the time you answer, I should know the proper answers. In either case, thank you.
Well explained.great contents ❤
Very nice video and very good explanation!!!
Brilliant Rob !!
@ThinkingandTinkering
4 жыл бұрын
cheers mate
Seems like a handy little hand crank generator I might be able to use something-like this thanks for sharing, if you config a Zener diode at about 5 / 6 v across the C storage in reverse bias it will regulate the V to that V and you will have a rudimentary phone charger 6v~ As long as the Zener wattage is not exceeded but I think it would be ok , you could parallel the Zener for more wattage. Regards
@ThinkingandTinkering
4 жыл бұрын
cheers mate
Thank you very much!!!
Thanks a lot, you were very helpful
I just found out that the new GM pickup trucks use stepper motors for their cooling fans, looks promising!
I like it. Consider using schottky diodes for lower voltage drop and more current.
@ThinkingandTinkering
4 жыл бұрын
for sure mate - I am likely to do a vid on the misfit based rectifier - almost zero drop
@ARandomTroll
4 жыл бұрын
@@ThinkingandTinkering please do- i want a bigger electrolysis PSU.
@hanslepoeter5167
4 жыл бұрын
@@ThinkingandTinkering I googled that but cannot find it. I suppose thats about using mosfets for controlled recification. I never found how to do that actually. A vid would be nice ....
@AdelsonDePaulo
3 жыл бұрын
I did something like that. But I noticed that my generator would generate for both sides. Is that okay or have I made a mistake with the coils wire?
@JonnyDeRico
3 жыл бұрын
@@AdelsonDePaulo what do you mean with both sides?
Those are the fingernails of a maker. :-) I love these videos.
@ThinkingandTinkering
4 жыл бұрын
lol - yeah - hard to keep them clean lol
Output is very impressive low rpm Great video Robert thanks man also did you know that you can use a Stepper Motor as a Bedini Motor you can use the same one you showed in this video all you need is to make the bedini ssg circuit then hook the stepper motor to the circuit 2 wires will be the trigger and the other 2 will be the power wires the power wires will be the coil with the most resistance and the trigger wires will be the ones with the lowest resistance the orientation of the wires don't matter for each coil but yes the 2 wires that go to the trigger have to go to the trigger what I'm saying is the start and the end of the coil doesn't matter just wire the 2 triggers to the trigger on the circuit and 2 power wires to power wire on the circuit and the the circuit has 2 posatives and 2 negatives so 1 set for the run battery and other for charging battery once it's hooked up just spin the stepper motor by hand give it a quick turn left if it doesn't start spinning then spin it right and you will see it spin it will hum and vibrate a bit on the table also use the potentiometer to a just the charing rate and speed and amp draw on the run battery also you can get it to go into self ossilation mode where it doesn't spin but vibrates and hums and will still charge would be awesome to see you make a video on this think it's very useful you don't have to worry about winding coils and making rotors just make the ssg circuit and get a stepper motor and 2 battery's and your good to go Cheers Mate
@ThinkingandTinkering
4 жыл бұрын
nice one - cheers mate
@clint9344
4 жыл бұрын
Ahh Thanks for the idea Brandon never thought of it from that perspective. Interesting to say the least will have to experiment with this. God Speed
Outstanding.
Excellent, very useful again. It was pitched just right for me and my current level of understanding. ( See what I did there? Groan)
Thank you!!
Great video thank you
@ThinkingandTinkering
4 жыл бұрын
Glad you enjoyed it
Thank you too bro.. for detailed video
I would like to see a simple design for an axial generator attached to a reciprocating stirling engine you featured a while back.
@ThinkingandTinkering
4 жыл бұрын
work on it!
Thank you sir!!
He's enjoying his job again.😉 👍👍👍
@ThinkingandTinkering
4 жыл бұрын
I certainly am lol
13:10 haha i love it, i actually got the same reaction 😂 Thank you very mu h that really helps me for a University project :)
really awesome!
@ThinkingandTinkering
4 жыл бұрын
Thank you! Cheers!
Thanks Sir ..... Thank you very much...😍😍😍😍😍😍
i understand stepper to diode to capacitor but how does it work after that? I want to use the stepper motor to charge a battery. What does the capacitor get connected to after? A charge controller? I would love a video of the next steps after what was said in this video. Example. i want to charge a 48v E-bike Lithium Ion Battery using a stepper motor as a windmill. I love the idea of the capacitor holding the charge and sending a continuous current even if the windmill isn't in motion. I am a visually learner and these videos are extremely helpful! I would appreciate any help!!!!
Brilliant!
@ThinkingandTinkering
4 жыл бұрын
cheers mate
Thanks so much! Super useful and inspiring. As a novice, when thinking about applications, I wonder about how to get a feel for dangers and limitations of this sort of project... e.g., Is there any danger of damaging the stepper motor by turning it too fast?
@ThinkingandTinkering
4 жыл бұрын
It's why I do so many small experiments mate - you get a feel but at low cost. Some folks complain I don't build enough big things - if I did that it would bankcropt me - do a lot of small - get a feel and then do a big
Great explanation and drawings Rob :-) If you are short of components, maybe you could wire the two coils in series or parallel before you connect to the bridge circuit. You would then only need 4 diodes and 1 capacitor.
@GRBtutorials
4 жыл бұрын
But the coils are 90° out of phase, so connecting them in parallel would be quite inefficient and could potentially damage the motor. Connecting them in series could work, though.
@solarhope
4 жыл бұрын
@@GRBtutorials Cheers for that, must confess I had not thought it through, got it half right :-)
@ThinkingandTinkering
4 жыл бұрын
you could do that mate - but often the coils are of different size and they are out of phase so there would be a bit of 'fighting' going on if you did that.
@solarhope
4 жыл бұрын
@@ThinkingandTinkering I should have known you would not be using twice the bits for nowt :-)
Oh yes. You got to stepper motors that’s properly awesome. These things are proper cheap. A CVT is a easy 3D printer job. This is proper exciting.
@ThinkingandTinkering
4 жыл бұрын
they are mate - that little one I showed with the gears is only £3
OMG thank you!... I have always wondered about making bridge rectifiers! Couple of questions... are there any sources of bridge rectifiers (or parts) in PC components (or even ready made) I could scavenge? AND Could I use a few (or many) super capacitors from the microwave I disassembled to get some storage to run 30 - 60 meters of 50/50 smd led strip lights?
I am sure that the 5 wire motor is a cheap way to allow micro stepping so you can pulse half a coil at a time and use a micro controller to control the pulsing sequence. I assume that the six wire motors are a similar thing. Thanks for your great videos. I would like to try a wind wall. It is not possible where I live to put up a turbine on a tower without the permission of all the neighbors.
Thank you so much....now I know how to wire it....I've been trying to find I formation on it, but it was way too confusing
ty very helpful
@ThinkingandTinkering
4 жыл бұрын
Glad it helped
Pretty cool stuff :)
@ThinkingandTinkering
4 жыл бұрын
Thanks mate
I enjoyed the video, thanks. I have 3 NEMA 17 stepper motors on my 3D printer. It is easy to generate a back EMF when moving the printer plate. I have to be careful to move slowly so I do not zap the electronics. I have seen the printer display light up. Not good. Testing for the wire pair which is a coil is easy to do without a multi-meter. Touch two wires together and try turning the shaft. If the wires are a coil pair you will feel resistance to the shaft turning. The splined belt comes in various pitches and widths. The belt should have the type, e.g., GT2, GT3, etc., but the pinion gear will not have a label, so unless you have purchased a specific pinion gear, it will be important to check the pitch on the pinion to ensure it matches the belt. GT2 and MXL pitches are very close but not interchangeable. My 3D printer is using GT2, but my latest project is an electronic step indexer for the wood lathe and it is using MXL belt, so I have to be careful not to interchange anything. Dave.
@ThinkingandTinkering
4 жыл бұрын
nice info mate - cheers
Look for outdated reprographic machines that are being replaced. On Craigslist I picked one up for free and another for 25 bucks US. they are loaded with high quality steppers and driver circuits not even close to their duty limit as well as other valuable components like capacitors and gear reduction motors. I probably harvested 20-30 steppers from these two
@ThinkingandTinkering
4 жыл бұрын
that is a nice post post mate - thanks for the info
Awesome video, I have a few large steppers laying around that now I know what to do with! What kind of amperage are you seeing with this set up?
@ThinkingandTinkering
4 жыл бұрын
not much mate - I was turning it by hand! Amp out put is going to be dependant on your input mate
Thank you Robert, I just logged into KZread after a very longtime so I could send a thumbs up, appreciation & subscribe! Have a question: What Step a motor or other technical spec & considerations would you recommend for a DIY hand crank mobile phone charger to actually charge the phone without damaging it?? Cheers, 🙂
I had a LG washer. It motor was a stepper motor. Realy big. If you turned it by hand it would power the light and buttons. Realy cool
@ThinkingandTinkering
4 жыл бұрын
LG - must look out for one
Great video! good thing i find this as i am planning on doing a wind turbine project! Just a quick question, does anyone know what was the voltage rating of the stepper motor used here? a help would be greatly appreciated! :D
Nice to watch your vid... Can i ask ? What type motor has least friction when generating output power ? Is motor with gearbox harder to turn on shaft ?
Hello Sir, At first thanks for sharing the wonderful information in the best easy way. I have few questions in my mind taking "Stepper Motors", hope you could answer them. Thanks in advance. Q1. According to you, which motor is best to generator electricity, and why? Options: A. Brushed DC Motor B. BLDC Motor C. Stepper Motor Q2. Referencing video, if I choose "Stepper Motor" as a Generator then which one to choose and on what parameters? We have, Stepper Motors with many different specifications such as a. Unipolar and Bipolar What I have learnt and understood watching videos on KZread (I maybe wrong, maybe right, please correct me if it goes wrong) is that, Unipolar is easy to use and works faster than Bipolar. Secondly, we don't need to reverse the rotational direction in the Generator, so we don't need "Bipolar". So, we should use Unipolar in Power generation. (Please clarify) - Which one to choose and what are the advantages and disadvantages? b. Low / High Torque Second factor that I get to know about is the "Torque". In my learning, torque is the rotational force that is required to push or pull something. But in our case of power generation, we are not going to use Stepper Motor as motor but as generator which needs rotation at a speed to generate some voltage. We are not pushing or pulling anything. So, we should not consider or least consider Torque. Low Torque - High Speed (Please clarify) - What motor torque should be consider in Stepper Motor as generator? - Is least torque motor best suitable for power generation? c. Low/ High Input Voltage There are different input voltages available such as (12V, 24V, 48V, etc) according to different sizes and different torques. - Do they have any relation to the output voltage of the Stepper Motor as generator? - Which is best suitable voltage stepper motor to choose to work as generator? d. RPM (Speed) Get to know, Stepper motors have different RPM (10000, 6000, 4000, 3000, 2000, 1500, 1000 or lesser) Smaller Motors have Less Torque but High Speed As the size increases Motors have higher Torque and Lesser Speed -Is it correct, that, more the speed more the voltage we would get? (Please clarify) -What is the ideal speed or RPM that we require to generate the desired or correct output (voltage) for power generation? e. Steps (Less / 200 / 400 / More) As per my information, Steps are only required for the accuracy to work. More Steps gives More Accuracy and Precision - Do "Steps" play a role in power generation which I don't think so, please clarify? f. Single / Double Shaft - Do we have advantage of double shaft motor instead of single, in case, if we put 2 rotors to rotate the shaft of the "Stepper Motor i.e Generator) for more smooth operation and speed? (Please comment and clarify) g. Geared / Non Geared As per my information, gears gives more or high torque. - Do we any advantage of geared stepper motor in power generation which I don't think so? (Please comment and share your views) What all factors are important and must be considered choosing stepper motor as generator? Also consider, other factor that I have missed which should be considered choosing "Stepper Motor" as Generator. It would be really helpful, if you would share your views and comment or prepare a video considering the above points. Thank you once again for sharing the informational video and look forward more similar videos from you. Thanks
@ArnookieVR
2 жыл бұрын
Stepper motors are the obvious choice. They are easy to wire and produce a good output. DC motors have brushe that degrade pretty quickly.
@navalkishoresingal
2 жыл бұрын
@@ArnookieVR Thankyou for your response, what about Brushless DC motors. Can you respond to any of the queries above for better understanding.
@ArnookieVR
2 жыл бұрын
@@navalkishoresingal I find stepper motors are better for hobby use overall. They are easy to connect and produce a good voltage evan at low speeds. This makes them ideal for DIY wind turbines & hand cranked generators. You would need to use a rectifier and capacitor on the output to get a nice stable DC output voltage. You can also use a car radiator fan for a super easy wind turbine. But you would need to increase the fan blades length. 😉
@ArnookieVR
2 жыл бұрын
Stepper motors are rarely rated on voltage. This is because of the nature stepper motors work by. Steppers are usually run on a low voltage. A NEMA 17 stepper would normally be rated 12 to 24v. But would normally be driven by 2v or even less ie when used on a 3d printer.
You should see if you can find a broken hoverboard and salvage the wheel motors from it. There are a couple of youtube videos from 'DIY King' using one in a horizontal and vertical wind turbine. The horizontal turbine seemed to work well, but I think the vertical turbine needed to be geared up for better performance.
@ThinkingandTinkering
4 жыл бұрын
cheers mate - I tend to use what I stumble over so if one crosses my path you cane sure I'll use it lol