often , japanese hornets show up when i've spilled some gas . they must be after ethanol too .
@thedoubtfultechnician8067
Жыл бұрын
I like my hornets like I like my mowers. Domestic.
@RK-kn1ud Жыл бұрын
Replace them with some cheap aluminum fuel cells (some fabrication required) and never worry about it again!
@DatBoiOrly11 күн бұрын
The problem is that the plastic itself is kinda porous on the microscopic level so even though the tank is "sealed" the ethanol in it slowly evaporates off through the plastic & attracts the beetles. so basically what I'm trying to say is if you coat the internal of the tank with a tank coating made for plastics you can basically seal up those microscopic holes that allow the evaporated ethanol to escape meaning those beetles never get attracted to it meaning no more holes.
@paulmcgrath2175Ай бұрын
Late to the party, but why not rig holders for a pair of marine tanks? They are common and relatively cheap. Come to think of it, you could cut the top halfs off and use them as a base to build a holder from.
@miken8001 Жыл бұрын
Would very much like to see a video on the smoke machine. would alsolove to build one.
@geniusanthony11 ай бұрын
This probably doesn't help at this point but, earlier this year I ran a test with different types of epoxy submerged in E85. After months the West System G-flex was still solid where the others have long since turned to jelly or become brittle.
@thedoubtfultechnician8067
11 ай бұрын
Good information for the future!
@dankirkpatrick3326 Жыл бұрын
Could you coat them in truck bed liner, or garage floor epoxy coating? Or maybe plastic dip?
@gypsydildopunks708315 сағат бұрын
A rat ate my fuel rail on my Dodge pickup. Nothing but gasoline and plastic, he must have been HUNGRY.
@bluesman48946 күн бұрын
Not sure what's more addicting the honey mustard or the buffalo ones.
@ville1981 Жыл бұрын
What happened to the F525!? I loved that one, specially it's rough terrain capabilities.😄
@thedoubtfultechnician8067
Жыл бұрын
Still mowing with that too!
@robertoruiz7069 Жыл бұрын
Funny vid and very informative i like it.Good repair job,tanks like that may only be under pressure when the gas heats up from the sun hitting on it.But at the current cost of new tanks i would look at just buying a ten gallon aluminum tank for a race car setup just cheaper.I'll start watching your channel it appears to be good.keep going.
@thedoubtfultechnician8067
Жыл бұрын
I’m considering dual Harley Davidson motorcycle tanks with flames painted on.
@vaderdudenator116 күн бұрын
Any details on that smoke machine?
@dannygoldman8216 Жыл бұрын
Hilarious as usual. Love the videos.
@JB_user568426 күн бұрын
they make an insecticide paint additive. in my humble and untested opinion, mix it with a gasoline proof paint and give it a try.
@croden9405Ай бұрын
Would ethanol free gas stop the beetles trying to get into the tanks?
@apeanders28 күн бұрын
Wait a minute. Now I know where I've heard that voice before. Mister Technician, are you in fact Jacob Geller, the top tier KZread video essayist? Your videos sure have similar qualities, however different the content.
@DSIVXX
26 күн бұрын
Nope
@apeanders
26 күн бұрын
(I know he's not. It's just a compliment by comparison.)
@bootblackingАй бұрын
Doing forensics in your church pants, rookie mistake
@SSJIndy Жыл бұрын
I think I would have just taped the holes over and put some Red-Kote tank sealer in (after a good interior cleaning, of course.
@thedoubtfultechnician8067
Жыл бұрын
Isn’t that just for metal tanks?
@SSJIndy
Жыл бұрын
@@thedoubtfultechnician8067 Don’t see any reason it would matter. It’s a tough, thick lining either way.
@thedoubtfultechnician8067
Жыл бұрын
Guess it depends on how it adheres to the plastic. I’ve used it with great success on my atv, but that’s a metal tank.
@Redneck0784 Жыл бұрын
JB Plasti Weld woulda worked better
@davedemo8229 Жыл бұрын
I go 60 miles for non eth gas. Havnt touched a carb since. btw do a video on the smoke machine. would love to build one.
@thedoubtfultechnician8067
Жыл бұрын
Let me figure out how to keep it from exploding before I share the design…
@davedemo8229
Жыл бұрын
@@thedoubtfultechnician8067 aw come on safety is overrated
@djrenault
Жыл бұрын
@@davedemo8229 safety third!
@willwobs70307 ай бұрын
try fiberglass
@hillppariАй бұрын
ethanol is the antiknocking agent. its not used for its energy content. would coud use something even more expensive or cheaper like lead lol
Пікірлер: 36
often , japanese hornets show up when i've spilled some gas . they must be after ethanol too .
@thedoubtfultechnician8067
Жыл бұрын
I like my hornets like I like my mowers. Domestic.
Replace them with some cheap aluminum fuel cells (some fabrication required) and never worry about it again!
The problem is that the plastic itself is kinda porous on the microscopic level so even though the tank is "sealed" the ethanol in it slowly evaporates off through the plastic & attracts the beetles. so basically what I'm trying to say is if you coat the internal of the tank with a tank coating made for plastics you can basically seal up those microscopic holes that allow the evaporated ethanol to escape meaning those beetles never get attracted to it meaning no more holes.
Late to the party, but why not rig holders for a pair of marine tanks? They are common and relatively cheap. Come to think of it, you could cut the top halfs off and use them as a base to build a holder from.
Would very much like to see a video on the smoke machine. would alsolove to build one.
This probably doesn't help at this point but, earlier this year I ran a test with different types of epoxy submerged in E85. After months the West System G-flex was still solid where the others have long since turned to jelly or become brittle.
@thedoubtfultechnician8067
11 ай бұрын
Good information for the future!
Could you coat them in truck bed liner, or garage floor epoxy coating? Or maybe plastic dip?
A rat ate my fuel rail on my Dodge pickup. Nothing but gasoline and plastic, he must have been HUNGRY.
Not sure what's more addicting the honey mustard or the buffalo ones.
What happened to the F525!? I loved that one, specially it's rough terrain capabilities.😄
@thedoubtfultechnician8067
Жыл бұрын
Still mowing with that too!
Funny vid and very informative i like it.Good repair job,tanks like that may only be under pressure when the gas heats up from the sun hitting on it.But at the current cost of new tanks i would look at just buying a ten gallon aluminum tank for a race car setup just cheaper.I'll start watching your channel it appears to be good.keep going.
@thedoubtfultechnician8067
Жыл бұрын
I’m considering dual Harley Davidson motorcycle tanks with flames painted on.
Any details on that smoke machine?
Hilarious as usual. Love the videos.
they make an insecticide paint additive. in my humble and untested opinion, mix it with a gasoline proof paint and give it a try.
Would ethanol free gas stop the beetles trying to get into the tanks?
Wait a minute. Now I know where I've heard that voice before. Mister Technician, are you in fact Jacob Geller, the top tier KZread video essayist? Your videos sure have similar qualities, however different the content.
@DSIVXX
26 күн бұрын
Nope
@apeanders
26 күн бұрын
(I know he's not. It's just a compliment by comparison.)
Doing forensics in your church pants, rookie mistake
I think I would have just taped the holes over and put some Red-Kote tank sealer in (after a good interior cleaning, of course.
@thedoubtfultechnician8067
Жыл бұрын
Isn’t that just for metal tanks?
@SSJIndy
Жыл бұрын
@@thedoubtfultechnician8067 Don’t see any reason it would matter. It’s a tough, thick lining either way.
@thedoubtfultechnician8067
Жыл бұрын
Guess it depends on how it adheres to the plastic. I’ve used it with great success on my atv, but that’s a metal tank.
JB Plasti Weld woulda worked better
I go 60 miles for non eth gas. Havnt touched a carb since. btw do a video on the smoke machine. would love to build one.
@thedoubtfultechnician8067
Жыл бұрын
Let me figure out how to keep it from exploding before I share the design…
@davedemo8229
Жыл бұрын
@@thedoubtfultechnician8067 aw come on safety is overrated
@djrenault
Жыл бұрын
@@davedemo8229 safety third!
try fiberglass
ethanol is the antiknocking agent. its not used for its energy content. would coud use something even more expensive or cheaper like lead lol