hi , i have done the same as shown in the video , but in the output panel , it shows nothing what should i do , can u sayy???please

if i want to add oled then what do i do?

Thanks you very much 🎉

sir can i use lcd for the output? If so how can i do that can you help me sir i try to follow your video abbbout this to i use mq 135 dht 22 and lcd can you help me sir?

@TechTrendsShameer

7 ай бұрын

Yes. You can use LCD. kzread.info/dash/bejne/lXp-sqevgpPYado.html

Sir program is not uploading to node mcu. Getting espcom upload mem failed plz help

@TechTrendsShameer

7 ай бұрын

Check port and board name

Hi, Good Day, can I ask on how to make the Status ONLINE? Hoping for a guidance in a kind response.

@TechTrendsShameer

6 ай бұрын

Thank you. If all the configurations are correct like variable names, wifi credentials etc, it will appear online automatically.

Sir, thank you for your amazing video and help me learn some knowledge. But i have question, how do i make my esp8266 online? I try upload the code through esp8266 using cable port. But once i upplug when finish uploading, the status said offline and plug in again it stay offline, Hope sir can give some advice to help me solve the problem

Sir please reply i have project exhibition tomorrow, sir code is running all is clear ,but output is not coming please reply

@TechTrendsShameer

2 ай бұрын

Any error message?

@playstation07

2 ай бұрын

@@TechTrendsShameer no error in code, but device showing offline

Hello sir, everything is working fine. But, I'm not getting the output on the dashboard, what should i do?

@TechTrendsShameer

12 күн бұрын

Can you double check the variable names and the circuit connection>? Follow everything as same in the video.

Can this work with Bluetooth??

Hii sir It show humidity was not declare in this scope

@TechTrendsShameer

6 ай бұрын

Check the variable name you declared is same as mentioned in the video. Otherwise you need to mention the variable name which you declared in the code.

code is verified and uploaded but i cant seem to see the output in the dashboard what should i do can you please help me its very urgent

@TechTrendsShameer

2 ай бұрын

Please double check the connection.

Sir if I use esp32 what will be the board name

@TechTrendsShameer

4 ай бұрын

ESP32 Dev Module. Check this video. kzread.info/dash/bejne/ma15urZrctrHgtY.html

Sir it says port is not available any solution?? Plz reply..

@TechTrendsShameer

7 ай бұрын

Install the Arduino Agent and try.

Tq sir it is working But I have a doubt that can we seen it in our mobile sir ?

sir my humidity and temperature is not function

@TechTrendsShameer

2 ай бұрын

Any error?

i not getting the board

@TechTrendsShameer

3 ай бұрын

Connect the board and install the Arduino Create agent.

Sir please provide a circuit diagram for this

@TechTrendsShameer

4 ай бұрын

Its mentioned in the video. Please check.

@vishald3521

4 ай бұрын

Yes sir but it is showing like block diagram( layout design) please provide me as circuitary figure

@vishald3521

4 ай бұрын

?

Sir code is not working please do something

@TechTrendsShameer

8 ай бұрын

Its a working code. May I know the problem you are facing?

@harshjagale1695

8 ай бұрын

​@@TechTrendsShameerI can't detect my nodemcu even after i installed the drivers

@raashmiphanitya1182

7 ай бұрын

Also can you tell me if this project can be done using nodmcu v3 version because j only have that

@raashmiphanitya1182

7 ай бұрын

please help me with this sir

@TechTrendsShameer

7 ай бұрын

Did you installed the Agent?