Air disk brake pad change and adjustment
Replacement and adjustment of air disc brake for a heavy duty truck or trailer application. This was done on a mock up please remember in your shops that all hardware should be changed. The service sheet can be found here: www.cbsparts.ca/admin/bulleti...
Пікірлер: 42
As a mechanic or sorts for over 50 years and now teaching air brakes (drum s cam and disk) this is I will say one of the better videos I have seen. You are personable but better yet as good as that is you are knowledgeable. Too many YT "mechanics" teach the shirt tail way (this is how Bob, and Bill before him and Sam before him did it.... I think you get it) I like your authority, your knowledge and our speaking voice is smooth as butter. Great video would really like to use it for the bench segment prep for my guys working on Disk Air Brakes. BTW we work on garbage trucks and container roll offs so we get stinky nasty brakes often. Good job!
You crack me up. I'm doing a pad replacement on school bus on Monday that goses down dirt roads Monday through Friday. The amount of caked on mud is of the scale.
New to the trade helped out a lot
Good video. When I do a pad change the kit comes with new hardwaredware including the sheer adapters. I save the old ones just in case.
@learndiesel528
Жыл бұрын
Great tip! you can never have to many shear adapters lol
One of the easiest disc brakes to work on.. Done a bunch of these. Also to check is the slides are worn out. Had one the bushings were worn out . The caliper would move up and down..
@learndiesel528
3 жыл бұрын
If you run across another one please take a video and send it to me. It will be good to get that information out. Les-
Thank you
Thank you for sharing your experience.dose the classic self brake adjustment work with disc brake as well or I should be do the same way you did on brake adjustments
wish i could go back
Thank you god will pay you.
thank you for video
@learndiesel528
3 жыл бұрын
You are welcome
Great video
@learndiesel528
3 жыл бұрын
Thanks!
@staceyhaynes7514
Жыл бұрын
How do you unloosed a rusted on shear adjustment
everything usely seez in Canada weather on the table it' look really easy
Ohk i did everything that way but u can drive a bit then it locks up when i go to adjustment points they are tight i loose them 5 klinks drive about 2km then they bind again
Were can i buy a sheer adapter ?
Hey , what can be wrong i did 3 clicks when applying brake pedal it holds when parking brakes are set no brakes , even i tried 1 click still the same , the chambers are designed to hold on when using parking brakes non of the 4 tires is holding brakes when you pull the knob
The washer is missing on the cotter pin side
What if I keep breaking the sheer adapter. The brakes are aired up and released.
@learndiesel528
3 жыл бұрын
It sounds like the tappets may be sized. The adjuster should move in both directions with the brakes released.
What is the adjustment on Bendix disc brakes that don’t click?
@learndiesel528
Жыл бұрын
I am not sure never worked on those.
how much does this divo system cost. the complete piece as you have it there
@learndiesel528
3 жыл бұрын
Im not sure I understand your question. Are you asking how much the mock up is??
@El.locote.305
3 жыл бұрын
Yes
What are the best brake pads to get
@learndiesel528
Жыл бұрын
Bendix
How you replace the rotor??
@learndiesel528
3 жыл бұрын
You have to remove the wheel end.
Would this apply to an FH 12 Volvo
@julyszn
10 ай бұрын
It’s very similar however this is a benefit for tractor trailers.
Shear adapter
Where can I get that socket
@learndiesel528
3 жыл бұрын
What socket are you talking about?
@joenero15
2 жыл бұрын
They do have an 11 point socket for those calipers there are many companies that make them lisle is one of them
Thauh - guess what. The facts please. We are not stupid.
Ok ok ok ok ok ok. Move on. I see I see.
Spit it out - uhh uhh
Thank you