One more step on the trailer project to complete spring assist for the drop-gate.
Жүктеу.....
Пікірлер: 75
@The_mare_stare2 жыл бұрын
That’s amazing and will help with my drop gate on vintage horse trailer
@michaelbradford2816
2 жыл бұрын
Good to know. It's funny how a small change can be huge in the field especially when dealing with an 1100lb animal! Take care.
@readplanet232 жыл бұрын
Thank You for the informative and educational video. I see a lot of great ideas for improvements to utility trailers. Have A Great Day! 🛻
@michaelbradford2816
2 жыл бұрын
Thank you. Glad it helped you.
@frankperry15434 жыл бұрын
Great video! I'm going to use your design.
@michaelbradford2816
3 жыл бұрын
Thank you
@howardtoob4 ай бұрын
Great job.
@ryanclark53755 жыл бұрын
Thank u
@JimRyserАй бұрын
Simple and works great!
@michaelbradford2816
Ай бұрын
Thank you for your comment today.
@john52chesser404 жыл бұрын
Say the trailer is parked on a higher patch of land than we’re the the gate would lay down, if it goes to far would those bent springs not slip and get caught on the bottom of the trailer?
@stephencooper49875 жыл бұрын
The only thing that I don't like is the spring end sticking out even though it's rounded off. Kind of like the the hitch sticking out of the receiver on your pickup. Good video though.
@davidsullins3700
5 жыл бұрын
he solves that at the end of the vid. its most the vid
@cfpau3 жыл бұрын
You should put a bracket on the mesh to prevent the spring from ripping it.
@michaelbradford2816
3 жыл бұрын
It's pretty tough as is.
@trenthearl13434 жыл бұрын
Micheal Bradford i think you have the springs around the wrong way. I would say the long arm of the spring is pre designed to take more load of the tailgate, as it comes down it slides up further thus taking less weight as it binds up. Which ironically reduces the force exerted on the spring as it binds up. Thoughts or am i wrong?
@enzoorciuoli328
4 жыл бұрын
long arm lever two me, on dah load
@dinofontana92422 жыл бұрын
Where did you purchase the springs? A very clean modification.
@michaelbradford2816
2 жыл бұрын
horsetraileraccessory store
@terrycannon8590 Жыл бұрын
Will you please send me a link where you about to torch the springs? I would love to do this to the lift gate
@bretneyman55773 жыл бұрын
Where are you get ion your springs and how much?
@ryanclark53755 жыл бұрын
Can u send me a link to purchase those springs please. Thank u
@enzoorciuoli328
4 жыл бұрын
i cant fine dem springs
@mikepalmer6655 Жыл бұрын
Thank you for the idea. We have enclosed trailers with ramp with the poorly designed torsion spring/cable system. Every 6 mo. or so I am repairing the system where someone runs into it with a piece of equipment. I am looking to either sell all the existing trailers and convert to the torsion spring trailers with the torsion springs at the hinge of the ramp door. Any ideas for converting? Any and all ideas welcome. Thx.
@michaelbradford2816
Жыл бұрын
One design I really like but could not get to involves putting a leaf spring under the trailer that works with a roller on the outer edge of the gate. It's a tough looking setup, but has to be designed from the ground up. I never liked the cylinder/chain or cable either. There are heavier coil springs by the way that could do somewhat the same function as the leaf spring. I don't have another trailer to experiment with or I probably would be attempting something new. Good to hear from you and please be careful with springs.
@hectorcalderon30113 жыл бұрын
Please include links when you're showing us something you use we might want to get one too
@joefarmer4238
3 жыл бұрын
Seriously ☝️☝️☝️☝️☝️ please 🙏
@daniellofy889721 күн бұрын
you may want to put a plate behind the spring so it does not wear a hole in the expanded metal
@michaelbradford2816
20 күн бұрын
Hmmmm. Well, I had one to do and it's a long time ago, but thanks for the suggestion. If I were needing to produce a number of these, I'd have some other much better set up you can be assured.
@jeffdiehl84834 жыл бұрын
Can you please also send me or post the link to buy these springs?
@michaelbradford2816
3 жыл бұрын
No links allowed here, but just Google it.
@wangometango3 жыл бұрын
Where did you find the 3/4" shaft springs? I can't find them.
@michaelbradford2816
3 жыл бұрын
I believe those were at horsetraileraccessory store all one word on the Internet. I can't put a url here since it's not allowed. There should be other sources. Oh yeah, the virus probably has curtailed production of things. Forgot about that. There are fewer supplies of things for now. I have nothing to sell or for sale. Look at trailer suppliers. Someone hopefully will get back to you.
@justindrake61614 жыл бұрын
By cutting a slot for the spring, you lost most of the strength of the gate at that lateral
@michaelbradford2816
3 жыл бұрын
No. It's a heavy box.
@rickwartman956
Жыл бұрын
@@michaelbradford2816 Justin is correct. If you don't think you reduced the strength of the angle when you cut the notch for the spring in it then you don't understand engineering.
@michaelbradford2816
Жыл бұрын
Neither of you saw the final result, so it is you who don't understand. It works well and I don't see any examples of your work either, by the way. Beyond that, I offer my experimental results to minds that profit from such. Simply put, if you can't appreciate actual results then it's probably results you didn't need, want or cared for. If you'd care to put on any of your actual work for evaluation some time, please know that the door is wide open for you on such a forum as this. I wish you well in whatever you attempt. Let's all look forward to your superior knowledge of engineering too. It'll be wonderful to behold I'm quite sure.
@unrestrainedfamily93564 жыл бұрын
How'd you get the 2*4 off?
@michaelbradford2816
3 жыл бұрын
Broke it.
@tiktokdancecomplimation88182 жыл бұрын
Where did you buy the spring at and what is its rating for pounds?
@michaelbradford2816
2 жыл бұрын
At horsetraileraccessorystore Not sure of rating, but more than you could burn through, however. Be careful with any bending or alterations. Avoid heating.
@terrycannon8590 Жыл бұрын
Where did you get the torson springs to do the ramp with?
@michaelbradford2816
Жыл бұрын
horsetraileraccessorystore.com
@beaustjohn23423 жыл бұрын
What is the brand name of these springs? Where can i buy them please? Thanx beau
@michaelbradford2816
3 жыл бұрын
No brand. Just Google it. I did.
@richardmiller37818 ай бұрын
what is the length of the spring and the lbs it will handle? Thanks for your reply.
@michaelbradford2816
8 ай бұрын
The length is about six inches and will fit a 3/4" bolt. I'm unsure of the exact loading for distortion, but it must be fairly high. I'd estimate at least 300 lbs. These don't fail. Severe cooling could be not so good, however. That's when springs are the most challenged.
@markthompson41414 жыл бұрын
Why didn't you show how you got all the stuff off the spring end before you completed the bend ?
@michaelbradford2816
3 жыл бұрын
Hummm. Just got tired I guess?
@papalilburn2 жыл бұрын
Underpowered springs!
@michaelbradford2816
2 жыл бұрын
No
@michaelnaylor6538 Жыл бұрын
What item number are the springs and where did you get them. I cant find that type
@michaelbradford2816
Жыл бұрын
horsetraileraccessorystore Part Number:RASHM112
@stevehicks83146 ай бұрын
where do you buy your springs?
@michaelbradford2816
6 ай бұрын
horsetraileraccessorystore.com They don't know me. Maybe they should?
@minersfromutah8000 Жыл бұрын
Where do I get those springs?????
@michaelbradford2816
Жыл бұрын
horsetraileraccessorystore.com Note: I don't do it for ad money. I get nothing.
@jeanuytico6233 Жыл бұрын
Looks like there could be another easier way with less time but thanks
@michaelbradford2816
Жыл бұрын
Yes. However, I wanted something that isn't available or even discussed. That extra tail comes in handy for a heavy gate where space is at somewhat a premium. My work is usually overkill, so don't worry. It probably won't be repeated by anyone. One thing it does show, however, is that the spring may still be worked cold without damaging it. My gate is really too heavy, but now it won't slam to ground.
@spanky72774 жыл бұрын
heat it up until it's red . Bingo
@michaelbradford2816
3 жыл бұрын
Nope. Temper.
@charliepowers52653 жыл бұрын
Not real smart guy. I don't have a lathe setting around to make tools to bend a made product.
@bradwatters15473 жыл бұрын
Torch???
@michaelbradford2816
3 жыл бұрын
Never. That would undo the tempering.
@bradwatters1547
3 жыл бұрын
@@michaelbradford2816 you already destroyed the temper In that section when you over bent the thing. You must be an engineer with your tools and jig. Just heat it and bend it over. I do this kind of work everyday for 30 years now
@bretneyman5577
3 жыл бұрын
@@bradwatters1547 where can I order these springs in bulk? And stainless would be a plus
@bradwatters1547
3 жыл бұрын
@@bretneyman5577 Try global industrial or McMaster Carr. Grainger has them , not sure about bulk
@gregkennedy93333 жыл бұрын
Why didn’t u just cut off excess material
@michaelbradford2816
3 жыл бұрын
The tails were important to me for this design. They provided push back I wanted.
@flintknapper6039 Жыл бұрын
OMG.....just cut off the excess. It lends nothing to the function when left long. You just need enough to contact the angle iron well. And weld a solid piece of metal on the bracket where you presently have the spring end pressing against expanded metal.
@michaelbradford2816
Жыл бұрын
That comment has come in before. However, I had a special need that the extended tail fulfilled. Not everything is always the same. I could have ordered a short tailed spring cheaper if that's all I had wanted.
Пікірлер: 75
That’s amazing and will help with my drop gate on vintage horse trailer
@michaelbradford2816
2 жыл бұрын
Good to know. It's funny how a small change can be huge in the field especially when dealing with an 1100lb animal! Take care.
Thank You for the informative and educational video. I see a lot of great ideas for improvements to utility trailers. Have A Great Day! 🛻
@michaelbradford2816
2 жыл бұрын
Thank you. Glad it helped you.
Great video! I'm going to use your design.
@michaelbradford2816
3 жыл бұрын
Thank you
Great job.
Thank u
Simple and works great!
@michaelbradford2816
Ай бұрын
Thank you for your comment today.
Say the trailer is parked on a higher patch of land than we’re the the gate would lay down, if it goes to far would those bent springs not slip and get caught on the bottom of the trailer?
The only thing that I don't like is the spring end sticking out even though it's rounded off. Kind of like the the hitch sticking out of the receiver on your pickup. Good video though.
@davidsullins3700
5 жыл бұрын
he solves that at the end of the vid. its most the vid
You should put a bracket on the mesh to prevent the spring from ripping it.
@michaelbradford2816
3 жыл бұрын
It's pretty tough as is.
Micheal Bradford i think you have the springs around the wrong way. I would say the long arm of the spring is pre designed to take more load of the tailgate, as it comes down it slides up further thus taking less weight as it binds up. Which ironically reduces the force exerted on the spring as it binds up. Thoughts or am i wrong?
@enzoorciuoli328
4 жыл бұрын
long arm lever two me, on dah load
Where did you purchase the springs? A very clean modification.
@michaelbradford2816
2 жыл бұрын
horsetraileraccessory store
Will you please send me a link where you about to torch the springs? I would love to do this to the lift gate
Where are you get ion your springs and how much?
Can u send me a link to purchase those springs please. Thank u
@enzoorciuoli328
4 жыл бұрын
i cant fine dem springs
Thank you for the idea. We have enclosed trailers with ramp with the poorly designed torsion spring/cable system. Every 6 mo. or so I am repairing the system where someone runs into it with a piece of equipment. I am looking to either sell all the existing trailers and convert to the torsion spring trailers with the torsion springs at the hinge of the ramp door. Any ideas for converting? Any and all ideas welcome. Thx.
@michaelbradford2816
Жыл бұрын
One design I really like but could not get to involves putting a leaf spring under the trailer that works with a roller on the outer edge of the gate. It's a tough looking setup, but has to be designed from the ground up. I never liked the cylinder/chain or cable either. There are heavier coil springs by the way that could do somewhat the same function as the leaf spring. I don't have another trailer to experiment with or I probably would be attempting something new. Good to hear from you and please be careful with springs.
Please include links when you're showing us something you use we might want to get one too
@joefarmer4238
3 жыл бұрын
Seriously ☝️☝️☝️☝️☝️ please 🙏
you may want to put a plate behind the spring so it does not wear a hole in the expanded metal
@michaelbradford2816
20 күн бұрын
Hmmmm. Well, I had one to do and it's a long time ago, but thanks for the suggestion. If I were needing to produce a number of these, I'd have some other much better set up you can be assured.
Can you please also send me or post the link to buy these springs?
@michaelbradford2816
3 жыл бұрын
No links allowed here, but just Google it.
Where did you find the 3/4" shaft springs? I can't find them.
@michaelbradford2816
3 жыл бұрын
I believe those were at horsetraileraccessory store all one word on the Internet. I can't put a url here since it's not allowed. There should be other sources. Oh yeah, the virus probably has curtailed production of things. Forgot about that. There are fewer supplies of things for now. I have nothing to sell or for sale. Look at trailer suppliers. Someone hopefully will get back to you.
By cutting a slot for the spring, you lost most of the strength of the gate at that lateral
@michaelbradford2816
3 жыл бұрын
No. It's a heavy box.
@rickwartman956
Жыл бұрын
@@michaelbradford2816 Justin is correct. If you don't think you reduced the strength of the angle when you cut the notch for the spring in it then you don't understand engineering.
@michaelbradford2816
Жыл бұрын
Neither of you saw the final result, so it is you who don't understand. It works well and I don't see any examples of your work either, by the way. Beyond that, I offer my experimental results to minds that profit from such. Simply put, if you can't appreciate actual results then it's probably results you didn't need, want or cared for. If you'd care to put on any of your actual work for evaluation some time, please know that the door is wide open for you on such a forum as this. I wish you well in whatever you attempt. Let's all look forward to your superior knowledge of engineering too. It'll be wonderful to behold I'm quite sure.
How'd you get the 2*4 off?
@michaelbradford2816
3 жыл бұрын
Broke it.
Where did you buy the spring at and what is its rating for pounds?
@michaelbradford2816
2 жыл бұрын
At horsetraileraccessorystore Not sure of rating, but more than you could burn through, however. Be careful with any bending or alterations. Avoid heating.
Where did you get the torson springs to do the ramp with?
@michaelbradford2816
Жыл бұрын
horsetraileraccessorystore.com
What is the brand name of these springs? Where can i buy them please? Thanx beau
@michaelbradford2816
3 жыл бұрын
No brand. Just Google it. I did.
what is the length of the spring and the lbs it will handle? Thanks for your reply.
@michaelbradford2816
8 ай бұрын
The length is about six inches and will fit a 3/4" bolt. I'm unsure of the exact loading for distortion, but it must be fairly high. I'd estimate at least 300 lbs. These don't fail. Severe cooling could be not so good, however. That's when springs are the most challenged.
Why didn't you show how you got all the stuff off the spring end before you completed the bend ?
@michaelbradford2816
3 жыл бұрын
Hummm. Just got tired I guess?
Underpowered springs!
@michaelbradford2816
2 жыл бұрын
No
What item number are the springs and where did you get them. I cant find that type
@michaelbradford2816
Жыл бұрын
horsetraileraccessorystore Part Number:RASHM112
where do you buy your springs?
@michaelbradford2816
6 ай бұрын
horsetraileraccessorystore.com They don't know me. Maybe they should?
Where do I get those springs?????
@michaelbradford2816
Жыл бұрын
horsetraileraccessorystore.com Note: I don't do it for ad money. I get nothing.
Looks like there could be another easier way with less time but thanks
@michaelbradford2816
Жыл бұрын
Yes. However, I wanted something that isn't available or even discussed. That extra tail comes in handy for a heavy gate where space is at somewhat a premium. My work is usually overkill, so don't worry. It probably won't be repeated by anyone. One thing it does show, however, is that the spring may still be worked cold without damaging it. My gate is really too heavy, but now it won't slam to ground.
heat it up until it's red . Bingo
@michaelbradford2816
3 жыл бұрын
Nope. Temper.
Not real smart guy. I don't have a lathe setting around to make tools to bend a made product.
Torch???
@michaelbradford2816
3 жыл бұрын
Never. That would undo the tempering.
@bradwatters1547
3 жыл бұрын
@@michaelbradford2816 you already destroyed the temper In that section when you over bent the thing. You must be an engineer with your tools and jig. Just heat it and bend it over. I do this kind of work everyday for 30 years now
@bretneyman5577
3 жыл бұрын
@@bradwatters1547 where can I order these springs in bulk? And stainless would be a plus
@bradwatters1547
3 жыл бұрын
@@bretneyman5577 Try global industrial or McMaster Carr. Grainger has them , not sure about bulk
Why didn’t u just cut off excess material
@michaelbradford2816
3 жыл бұрын
The tails were important to me for this design. They provided push back I wanted.
OMG.....just cut off the excess. It lends nothing to the function when left long. You just need enough to contact the angle iron well. And weld a solid piece of metal on the bracket where you presently have the spring end pressing against expanded metal.
@michaelbradford2816
Жыл бұрын
That comment has come in before. However, I had a special need that the extended tail fulfilled. Not everything is always the same. I could have ordered a short tailed spring cheaper if that's all I had wanted.
You just weaking the ramp with that slot
@michaelbradford2816
3 жыл бұрын
Not really.
Should see me