I just love the way how you, analytically, decide how to approach each different challenge

If I could find employees with this attitude and pride in their work I would work till I was 100. He is such a joy to watch!

Best repair guy on KZread. If you’re into soldering for work or pleasure you won’t go wrong subscribing to the channel!

I need this exact job doing in the UK, I'm struggling to find someone. Top job by the way.

Greetings from australia again Its always enjoyable to see the diversity of work that passes thru your repair facility It keeps you alert and on your toes Stay safe and keep up the great work

I absolutely love this guys work, he thinks out side the box!

@NorthridgeFix

4 жыл бұрын

Thanks brother

Dismantling n Putting it back strategy is superb. Thx for the knowledge shared

absolutely perfect, i check almost everyday your videos, your work is even better than from the factory, and u are a super friendly person, keep it up !! greets from Belgium.

@jamesbrown99991

3 жыл бұрын

Even at 5:40?

Is the low melt soldet only used to lower the melting point of the solder joints or is it also used for soldering components?

rather than desolder the aux connector heat uo the black rubber and pull the charge board out this allows full access with minimal effort

Really good job👍 looks like an operation in a hospital 😂 awesome desing of the board, awesome job.

Nice job. Great idea how to fix this.

My micro charger port pins broken..do you know where can I get the parts online?

That's it. I had to order the low melt solder and your solder braid. It looks so much faster than the solder sucker. Order placed.

VERY HARD AND BEAUTIFUL JOB THANK YOU SIR

How can it work with the connector desoldered at 5:50, not one pin making contact!!!

@jamesbrown99991

3 жыл бұрын

Yeah, I was watching that connector bubbling and melting. I hope he tested it before shipping D:

Love to see your beautiful work Kindly told us the blower speed and temp of the hot air gun from your soldering station.

Where can I obtain the lightning charging port? Do you happen to have a part number for it?

What beat pill+ that won't charge nor turn on, and drain battery instantly?

I have the exact same issue with mine A friend inserting a android charger by froce So now it won't charge How much would this repair cost ? (Not in a hurry)

I did one of those a while back. Fun times.

@matheusfelipe2776

3 жыл бұрын

Pode me dizer um link onde posso comprar um conector como este? Eu tenho o mesmo equipamento para reparo na minha bancada aqui no Brasil e eu não posso comprar esse conector

شكرا اخي العزيز

Good job!

Best job 👏

Great job and video

If the beats charging lights comes on normally but when i unplug the charging cable, the charge goes to zero power as battery don't hold charge. Would this be bad charging port or bad battery?

@harrisahmed2017

3 жыл бұрын

Could be either really

Are you in the US? How much for this fix?

Where did you get the nee charging port from?

Great Job ! Could you do a video about the soldering irons tips you are using ?

@paulzac5481

4 жыл бұрын

Was thinking of that myself. I have various tips but not like the bent tip he's using.

@elsabaa85

4 жыл бұрын

Detecting Dazza can you guide us to the video ?

@NorthridgeFix

4 жыл бұрын

I"ll do one soon.

@elsabaa85

4 жыл бұрын

NorthridgeFix جزاك الله كل خير

Awesome like always

What did you charge for the repair?

Better than Factory!

Thanks

Thank you M.r

موفقك ...عمل ممتاز

Awesome

Hi, i love your job i have a nice touch. Can i ask you what cause a phone to flickering white screen if you try to lower the brightness below 70%

@NorthridgeFix

4 жыл бұрын

Hard to tell. It could be a lot of things depending on the make and model of the phone.

@CCellService

4 жыл бұрын

@@NorthridgeFix it a galaxy note 9 and s9 plus i never drop this two phone no water damage no over charge, this happen after i put my phone on wireless charging it start to flickering after 12 minutes i leave both phone on it. Thank your for the reply

@jamesbrown99991

3 жыл бұрын

@@CCellService Hi, apparently this issue is quite common with AMOLED in the S9+. Try the "OLED Saver" app, which purportedly works.

GOOD JOB

First congratulations on the great work done !! I have a copy of this one here in Brazil with the damaged Lightning connector, is it possible that you tell me where I can buy the Lightning connector or would you send it to me? if yes what is the contact or link for purchase and shipping to Brazil, is it possible to remove from some iphone model ??

@kilner79

3 жыл бұрын

hello did you source one ?

@matheusfelipe2776

3 жыл бұрын

@@kilner79 I still haven't got it, I haven't found it for purchase nor a card that has the connector nor the connector

@kilner79

3 жыл бұрын

@@matheusfelipe2776 I have found it

@kilner79

3 жыл бұрын

@@matheusfelipe2776 it comes in white and black also

Masha allah good job

what flux do you use?

@NorthridgeFix

4 жыл бұрын

northridgefix.com/product/amtech-nc-559-v2-tf-flux-10g-syringe-plunger-2-needle-sizes/

Sir is it possible or not to send low melt solder to India

@NorthridgeFix

4 жыл бұрын

Yes we ship worldwide. Choose india during checkout.

That's a really screwy design. 😎

Great video! But, BEATS are garbage.......

😍😍😍 خلص

@NorthridgeFix

4 жыл бұрын

أحسنت . مركز منيح

❤️❤️❤️❤️

Ya خلاص الأخ لبناني؟

Please reply sir