wow are you kidding me? you are a master at this craft. these are the best inlay cutting boards I have ever seen on you tube or anywhere else. I been doing CNC and inlays for a few years and I have yet to produce anything even close to what you do. thanks, I love watching your masterful creations come to life.

@MandSWoodworks

6 күн бұрын

Super kind words! Thank you for the compliments and thank you for watching!

Just stunning craftsmanship. I've had my CNC for about a year now and made some great things but have not attempted wood inlays yet. You're describing your process and failures is inspiring and I need to just go for it. And, no shame in being a "KZreadr", sharing your tips is helping others to create. Thank you.

Hey! Great video and really enjoyed your laid-back style and information! I make similar boards and also use VCarve Pro. If you're like me, you've probably landed on a "standard" carve depth, etc. and, if so, there's a way to trick VCarve into carving the male plugs in multiple passes instead of plunging all the way to your final Start Depth (SD) and potentially breaking bit tips as you mentioned. I go a bit deeper with my inlays so if you wanted to take three passes to get to a final carve depth of 0.345", you can run your first toolpath at a SD of 0.295" and a FD of 0.05". Then save that toolpath as your final depth toolpath (which would be your #3 toolpath). Create another toolpath with a SD of 0.2" and the same FD of 0.05" - this is your #2 toolpath. Then create your #1 toolpath with a SD of 0.075" and a FD of 0.05" (your FD stays the same throughout). Then manually reorder your toolpaths to group your clearance bits/paths in order from 1, 2, 3. Now... this sounds like a lot of work but in reality it only takes a couple of extra minutes and you minimize the chance of blowing a bit by down a deep plunge. And you can ramp up your ipm rate...!

@MandSWoodworks

11 ай бұрын

Thank you for the info! I'm gonna give that a try! Thank you for watching!

@calebsanz9826

11 ай бұрын

This is how i do mine as well. Its a great tip.

Thank you so much for your time and wisdom on inlays. I watched this video before purchasing a Cnc and now that I have one and I've been practicing I've rewatched and have gained a lot more from this video. Many thanks. I hope to be able to produce something close to this level myself in the future! we don't just hit run on a machine!

I really like your style of instruction. Very concise and detailed without being too complicated.

Super Nice and Inspiring Thank You

I just watched this with my kids, who were all under the age of 10, and they were captivated and loved it. Great work! “I loved it.” - Stella.

@MandSWoodworks

11 ай бұрын

This is the best comment I have gotten yet! Thank you so much for watching!!

As someone who's devoted over 50 years to professional engineering machining, including 25 years in CNC, witnessing your skills in woodworking and CNC, despite being newer to these crafts, is truly inspiring. Drawing motivation from critiques is crucial; trust me, machining stands as a skill on par with any other

@MandSWoodworks

6 ай бұрын

Thank you for the kind words!! And thank you for watching!!

This is incredible! A simple "Thumbs-up" is not nearly enough ...

@MandSWoodworks

2 ай бұрын

Thank you!

Great video, but that clamp rack you have is just brilliant

Beautiful. Well done

hey, your a great teacher, the words you pass on from your lessons of failure and success make you a master craftsman. own it dude your a master at your craft an you have left a legacy.

" I am not a woodworker" ????? BUDDY! You are a Woodworker Extraorinairre!!! MAISTOR!!

Ive had to have a beer after soooo many carvings. LOL. Great Vid!

Are you convincing me to buy a CNC router and become a "not woodworker" too? Because I am convinced by this beautiful art. Take care you too.

@MandSWoodworks

11 ай бұрын

I don't want to suffer alone. 😁 Thank you for watching!!

Unflipping real - that is incredible!!! You do an outstanding job and explained this so well - thank you. And yes you are a woodworker.

@MandSWoodworks

Ай бұрын

Thank you!!

You do fantastic work

With this quality, you've definitely minded your Ps and Qs. Seriously though, great craftsmanship. Lookin fwd to your next video.

you sir sound so humble and genuine i cnc my self i no the time and frustration that goes into a job but when you hand someone the end result its well worth that reward that comes from the heart..nice job!

I dont think youre giving yourself enough credit. As a woodworker, I say you are definitely a woodworker. Very nice work.

Thank you

This is a real beauty. Your friend is getting an exceptional gift that would make a great heirloom.

Wow! Right up there with broinwood! I now have so many questions that I don't know where to start! Thank you!

Is there an award for best new youtuber of 2023? You have my vote.

@MandSWoodworks

11 ай бұрын

Your comment literally made me laugh, but in the best way possible. I don't have the polish and production savvy most folks on here have. So I am truly honored and humbled by your comment. Thank you!! Thank you for watching!

Brian better watch, a student is about to pass you up !! lol. VERY nice cutting board, well done !!

I'm sure your friend is more than proud to have that work of art on his wall or countertop. I's beautiful.

Best is a relative statement. What I saw was some pretty darn good work! I do 3D carvings with my CNC mill but I do like the looks of the inlay work.

In the words of the late Great Jackie Gleason ( Sheriff Buford T Justice ) SOMEBITCH You are a Talent Sir. Thanks for sharing.

@MandSWoodworks

Ай бұрын

Junior: "My hat just blew off Daddy!" Sheriff: "I hope your GD head was in it! Thanks for the laugh and the compliment and thank you for watching!

Thank you for this video I enjoyed it.

You very humble sir. This is a beautiful piece of art. I could listen to you talk about your work for hours. As a fellow Deep South fella myself, I applaud you and your work. Earned a sub and a like easily.

I am digging that glue up jig you have!! I haven't seen that before.

Fantastic work! looking forward to the next video.

Terrific. Liked and subscribed

A job well done, if I ever saw one. Thank you for sharing. / Peter

What a beautiful friend. Lovely work and what a friend because you put a lot of time into this from thought all the way to creation

Masterpiece!

Very nice project and well executed. It is defenitly useful video. Cheers

Videos like this give me the confidence to try inlays. Thank you!

Beautiful 😢

I think we are all digging it!!! Thx!

As a fellow cnc’er that started with end grain cutting boards 2 years before I got my cnc this is amazing and you have got a subscriber in me. Love to see what you do next!

Thank You, Thank You, Thank You. This was an outstanding video. You give an old guy like me hope that we might actually be able to do something like this. Thank You again.

Great work and video. I like quite a few things about your work no like the work holding (that’s like Broinwood). I also like that you shared your depth settings. Thank you. I’ve been doing quite a few and am Still learning how to get that super fine detail. It’s starts with end grain! I’ve learned that much too. Great job. Keep it up. I have my end grain board all glued up, now I just need to do my first cutting board inlay.

Wow, fantastic work, I had no idea you could make something this detailed on a CNC. Thank you for sharing!

WOW! Thanx for sharing!

Awesome job!

Incredible!

Outstanding...Salute!

I'm liking that jig that holds all the pipe clamps in position, gave me an idea!! Great video and i am also looking to get into inlays.

That was really fun to watch! I love to see the art that other people create. I can tell you that if my dad was still alive he would have watched your video again and again to enjoy all the details!

Thank you. Stunning.

You do some beautiful work. Enjoyed every second of your video.

Simply amazing work you have created. During the build I was thinking to myself I wouldn't ever use it as a cutting board since it's too beautiful. I'm glad to hear you buddy said a knife will not touch that board. GREAT WORK!

I’ve really been resisting cnc, because I just don’t how to get one that’s affordable, or even how to learn how to use it. Your work is amazing, and inspiring, and I thank you for posting it. I like your style. So many woodworkers on KZread joke around so much it gets annoying. I just don’t like it. You get right to the point and your voice is very soothing. I guess I’m too old for all those youngsters channels. 😁 I have liked and subscribed, and I look forward to see what you make next. As a Navy veteran that grew up on an island off the coast of Maine, I love the sea, and I love this board so much! It is absolutely gorgeous! Okay my friend, you take care and I’ll be seeing you around! ☮️ & ❤️ from a fat old woodworker in rural Oklahoma!

@MandSWoodworks

11 ай бұрын

Thank you for there kind words. And thank you for your service sir!

@HaWiWe

9 ай бұрын

You can build your own for under 1000 dollars and can do inlays with it as well.

Stunning.

Thats fantastic!

Duuuude! this is just gorgeous!

One of the few video's I watched from start to finish without fast forwarding, Extreme craftsmanship and a lovely piece.

Absolutely stunning work man! Good job

Beautiful work. 👏👏

Stunning!!

Wow! Very Impressive! Just a beautiful piece of workmanship.

Amazing work!

GREAT JOB !!!!!!

Very nice woodworking. I've only had my CNC for maybe 9 months and I'm learning as I go and I ran across your page and I really wanted to learn how to do this type of woodwork.. may God bless your business

I'm starting my woodworking career now and this was captivating. Absolutely beautiful work sir.

A true work of art for cutting boards very nicely done

Spectacular!

Absolutely great video, thank you for the upload. Your first video was quite impressive for an opening film, but you really stepped up the production quality on this one!! You deserve 100x as many subscribers as you have. Would you mind doing a quick video on your waste board setup? I really dig those PVC stops and it looks so much more practical than all those T-track setups.

Awesome video thank you

Thank you for sharing. Love your work and the style of your video. Looking forward to future projects.

That's gorgeous. Thank you for posting your process and result!

Wow looks amazing great job

Absolutely stunning work mate.

A really nice job! I had seen when broinwood did this vector and I also like it alot.

Awesome video!

Nicely done Sir!

Outstanding, sir!

Amazing work and great presentation with the video.

Absolutely beautiful work.

I’ve just found you and LOVE your content. Looking forward to more.

You've done a mighty fine job. I'm inspired. Sir Your humility and attention to detail have not gone unnoticed. ❤❤

@MandSWoodworks

11 ай бұрын

Thank you so much for watching!

Very cool project)

that is one beautiful board. Keep it the great work. Its a pleasure watching a artist perform

Amazing detail and explanation!!

Wow. Wow.

Your work is just incredible! The inlay work is beautiful,and the process you use for it just blew my mind! I can see why someone would pay top dollar for one of your boards.

Love your spoilboard

Absolutely gorgeous pice of work. Thank you for sharing.

beautiful! I've been in love with Broinwood's work for awhile, Glad too see another amazing CNC artist as well. I've recently started trying my hand at inlays, hopefully your help will get me to the next level, can't wait to see more!

Amazing stuff. Great board and great video.

You are awesome, I hope to be able to do even half as good as that....

Beautiful board! Very informative. Thank you for that. Most videos just skim the surface.

WOW!! Give yourself some credit. That board is amazing.

Nice Job!

That was one of the most inspiring CNC videos I’ve seen. Thank you so much for making this video!

Gorgeous work!! Thank you for the tutorial and your #’s.

Very beautiful work! Yep Broinwood inspired me to get a machine. Made all the signs and some epoxy inlays so far. Ready to learn these beautiful Vcarve inlays you guys make. Thanks so much!

What a pleasure to watch. Stunning results. Just got my Vcarve pro sofware and very pleased so far.

Thats amazing!!