I'm a mouth breather and apparently did some unnecessary steps in this video I apologize **It might not be necessary to unbolt the strut and ball joint to perform this upgrade**

@jake2772

11 ай бұрын

Does this squeak or make any noise over OEM?

@PoorManMods

11 ай бұрын

@@jake2772 nope

Man you should have looked on club Lexus first would have saved a sh#t load of work, you don't have to remove the ball joint or the shock bolt, anyway you got it done cheers from OZ.

@PoorManMods

4 жыл бұрын

Yeah oh well, the important part of this video is the press section

@hoarbaby

4 жыл бұрын

Lol man you did take the long route, you basically took apart the whole suspension to replace that #2 bushing. I did this as my first mod years ago and it is a good one!

@donmakavelio

4 жыл бұрын

How do u do it with out removing most of it?

@rms13mike

3 жыл бұрын

@@donmakavelio undo all the bolts around the bushing and just pry the LCA down and out away towards the wheel to where you can just pull the bushing off the LCA

@Icecreameliora

3 жыл бұрын

Yes sirrr thank god i watched one before i did it i was doing it for a CLIENT but i plugged him so it wasnt payed in cash just ig clout haha but def glad i didnt use this single reference and found the easy video on doing this

good shit bro, just the video i was looking for. Im working on a 2011 is 250 but the lower control arm severely bent from accident. was making sure my disassemble process was correct and it was... yay

Holy shit you did so many extra steps lol. As an actual mechanic, you can just undo the two bolts holding the mount (and a few little things in the way) and the 22mm nut holding it in on the back. Then slightly loosen the front bushing, pry down on the arm, pull out the bushing. Then to press it out, just press it out. With real tools. Seriously, did two pairs of these in a few minutes each unlike your back method. The whole process for me from getting on the rack to having it aligned and back in the customers possession was faster than your whole video.

@eeyaye

Жыл бұрын

Where’s your shop?

Thanks for the info. The day I stop learning is the day I die. Peace.

That ball joint is why you should always shop around .

Mind to share the link where I can get this bushing bro, thank you!

These also fit on a GS and LS as well!

@mechanicalintentions5431

Жыл бұрын

I have been looking for LS600HL bushings. You know for sure they have bushings for them as well?

I did this in about 8min lol don’t have to mess with the spindle or knuckle at all

@PoorManMods

4 жыл бұрын

Haha yeah i realize that now LMAO

@terrancecollins2696

4 жыл бұрын

Poor Man Mods yeah but you inadvertently helped me see how to do the lower ball joints so you are appreciated! Lol

will rcf bushing work just as good?

Hello long time no see you man be careful and stay safe take care you family man god bless you and your family

@PoorManMods

4 жыл бұрын

Thanks!

Question - I have a 2014 GS Fsport RWD and the stud that goes from the control arm into the rear bush broke due to being hit. I was wondering if you can help with a replacement part

do these make any noise after wear?

Wow! Like the new shop!

@PoorManMods

8 ай бұрын

This is the old shop! 😄

@blownaway4371

8 ай бұрын

@PoorManMods 💥 Oops. It's been a while. Went through a divorce and going to be doing mi is300 suspension like what you did. So thank you for that

@PoorManMods

8 ай бұрын

@@blownaway4371 youre welcome! sorry to hear about the divorce :(

Which lower ball joint did you get? I recently had mine replaced and order from RockAuto. I ordered the Proforged ones instead. I'm out of the country right now and can't really tell you how they performed.

@PoorManMods

4 жыл бұрын

Just beck arnley

Very well video.Bravo bro.Thank you very much👍🤝👏👏👏👏👏

@PoorManMods

2 жыл бұрын

Thanks!

Can you put the part link here please?

Next time put the bushing in the freezer so you can press it in easier

Hi I have a IS250 2007 SE in the UK. I want to clear some bumps faster but always have to slow down more unlike a BMW M Sport. Which suspension can I have without making it too hard or overly sporty

@liquidh5226

4 ай бұрын

Should buy a Toyota Landcruiser bro 😂

Nolathane bushing is just as good and reasonably price

What brand is your press? I was thinking about getting the 20 ton harbor freight press.

@PoorManMods

4 жыл бұрын

Im not sure of the brand

Any one got a part number for this?

do videos on that Z in the back 👀

@PoorManMods

4 жыл бұрын

Not my car!

Will this work on a awd gs 350

@PoorManMods

10 ай бұрын

i think so

Enjoy the videos mate ... but the way you say cone makes me laugh.

@PoorManMods

4 жыл бұрын

Lol the way i say cone?

@MightbeAmechanic

4 жыл бұрын

Yea 3:57 not sure why 😂

Wait what does this do for the car?

@junior17medval

2 жыл бұрын

Did you not watch the video. He explained it in the first minute of the video.

Driving impression?

@PoorManMods

2 жыл бұрын

I dont drive the car hard enough to notice a difference, i mainly did this for the tire wear improvement

Is this worth the money??

@PoorManMods

3 жыл бұрын

Yes

You may as well have removed the front and rear windshield also, just to add additional unnecessary steps 😂

@PoorManMods

Жыл бұрын

yeah i figured that 😂 might remove the trunk next time

You did not need to remove the spindle etc

@PoorManMods

3 жыл бұрын

i know that now

This isn't a poor persons way. This is person with access to shop presses and equipment. The average person will have to pay a shop to press them it and that will be almost as much as buying them already pressed in. You also did way too much work in the removal process.

@PoorManMods

3 жыл бұрын

It is the poor way. I saved hundreds by buying just the bushing and doing the work myself, instead of buying it already pressed into a bracket.

@junior17medval

2 жыл бұрын

You can’t make everyone happy. I bet if this video wasn’t made there would be people complaining, “WhY IsN’T ThEre a ViDeO ShOwiNg HoW To PrEsS In ThE BuShInG!”

@Jedi_Luke

2 жыл бұрын

@@PoorManMods Obviously you didn't read the comment. Yes YOU save money, the average person doesn't. Plus the fact you still didn't too much extra just like a lot other comments are saying. Smh

@Jedi_Luke

2 жыл бұрын

@@junior17medval If this video wasn't made, there would be a better video by someone else and life would still go on without you getting upset 🤣

@junior17medval

2 жыл бұрын

@@Jedi_Luke there are better videos out there and poor man mods has noticed it too. I just don’t complain to youtubers who take time out of their day to show people like you with a smooth brain to understand that there is no one way of doing things. It’s obvious that diy people don’t have a press, or professional equipment to get the job done like he did but maybe you have a buddy that does or friend or shop that won’t charge you a lot of money. It’s called doing your research. And who said I was upset, your the one getting your panties in a bunch because poorman didn’t do it the way you wanted to. 🤦‍♂️

It cracks me up that people think urethane bushings are so great. Yes they offer more precise handling, but at the cost of added vibration and harshness! This is a fact. I have an IS250. Beautiful car that rides like a Lexus should. That said it’s not a race car. Either is a IS350 or even an ISF. If you want one buy a Corvette. As for me I’d rather not ruin the ride that Lexus IS known for. To each their own I suppose....

@PoorManMods

4 жыл бұрын

My penis works just fine, I dont need a corvette.

@asiahispanico

4 жыл бұрын

You buy the lca bushing to correct the inner tire wear (along with a proper alignment). Lol you sound like someone thats never driven an ISF, assuming its not a performance-oriented car. Stay in your lane (the far right one please) thanks.

@thisnameisnotfake517

4 жыл бұрын

An isf has harsh ride quality from the start its a performance car.

@nordicpride9708

4 жыл бұрын

Thisname Isnotfake performance car....😂😂😂

@thisnameisnotfake517

4 жыл бұрын

@@nordicpride9708 yeah homie its the F model... literally google "lexus F" 😂

Dude, I love your videos, but dude... you should have just bought the entire unit. I bought the entire unit.

@PoorManMods

4 жыл бұрын

Thanks but why spent double the money when i dont have to?

@toumashenry9068

3 жыл бұрын

DIY is better 🤣😂

@jth858

3 жыл бұрын

If money isn't a concern then yeah, the channel is called "POORmanmods", soooo.

@mr.paulwu

3 жыл бұрын

Mind to share me the link on where I can order the whole unit bro? Ty

@talknheadz

3 жыл бұрын

@@mr.paulwu he doesnt give the link to help us buy it..smh

Bro you did this sooooo extra you can remove the bushing with everything together and just a big pry bar by the bushing and the frame stop wasting ppls time

@PoorManMods

3 жыл бұрын

Yeahh 😫

@Icecreameliora

3 жыл бұрын

@@PoorManMods Dont just yea meeee i almost did it this wasy if i didnt search more and find a better video i would have been out hella time for a plug i was giving someone not even getting paid

@PoorManMods

3 жыл бұрын

Yeahhhhhhh 🤣

@Icecreameliora

3 жыл бұрын

@@PoorManMods Haha fucker, hope youre having an amazing day and weekend tho! Many blessings

@PoorManMods

3 жыл бұрын

Haha thanks so much, i hope the same for you 😁