Thanks alot for your answer and help. Also, congratulations for this DIY, the only and the best i found around the web. thank you!!

Yes chuyetax - as 3/8" wood was used for the entire project, so were 3/8" rivets. Keep in mind that if you use a different thickness of wood, say 1/4" or 1/2", you'd need to use different length rivets. Hope this helps.

Just ordered some of your hardware, great video. Thanks for everything!

@reliabledan

6 жыл бұрын

Thank you! We appreciate your business -

Back-up washers are most important for handles, latches and any other components that are subject to strain. While it can't hurt to put back-up washers on other "passive" components it's not a priority. Hope this helps.

I am just wondering with all those parts, how much I can actually save building it myself. Seems like the labor is better suited to someone with air tools and a large work area.

As a matter of fact we are putting the finishing touches on a terrific NEW sliding shelf made specially for DJ's. It should be ready for sale in less than a month. Go to our web site, ReliableHardware . com and sign up on our Mailing List (upper left hand column) and you'll receive notification via an E-mail. Hope this helps.

If the inner holes of the hinges were riveted first, then washers could be used for the outer holes where there is no aluminum behind them.

Hey there! Great video! Do you have guidance on how to measure and cut for the recessed clamps? I’m trying to convert 4 traditional hinges to a few twist lock clamps

Thank you for sharing! What size rivets do you recommend?

Do you guys carry something that I can make a sliding shelf with? Like the DJ cases that have sliding laptop shelves?

The drill bit you are using looks like it has a stop on it, is that out of your personal collection or does it come with the pack of rivets? Now onto the real challenge... making a flight case house ;)

The corner ball and latches have recesses to allow for the corner angles and tongue and groove....what size corners are they? small med or large?

i like to built a case for 2 55 inch tv , so what material i have to buy expect plywood ??

No washers on the back of the corner clamp rivets?

good video thanks a question where can I buy the pieces

RH-0608 - thanks for asking.

nice. help full

a doubt, as the tool used to press the drawer is called, which has a strap that surrounds the drawer

excuse me!! every rivet that you used, is the same 3/16 in all the road case work?

maybe it would be wise to tell customers in parts 5 and 6 to not put rivets at the ends of the extrusions so they don't get in the way of those corner pieces.

"...and we'll blow off any shpilkus that might get in the way here!" ?! awesome. this guy is rad

Cool and thanks for your help

@reliabledan

5 жыл бұрын

It's always good to know that our videos helped. Thanks for watching!

So I am putting together parts for a custom case. For my angle extrusions, I need low profile, so using 3/4 inch ones. Other hardware, like the small ball corners and latches I have selected do not seem to have the slight recession to allow for the extrusions. Is that a problem when you put it together? Do they just bend when you rivet them?

@reliabledan

6 жыл бұрын

You are correct. They are designed to bend slightly for a tight fit.

What is the size of rivert for 3/4 plywood? Also the size of washer?

What is the part number for the corner clamp mentioned at 1:12? I can't find them on the website.

Thnx for info Im starting a new job building these next week much appreciated kiwi-phill

awesome

I have a 20 year-old custom guitar case and the tension gets too tight before I can completely close my latches. Is there something I can do to loosen up the tension?

The lid that I'm designing is 3 inches. I haven't picked up my pieces yet just designing it. Is 3 inches enough room for the ball corner and the 2 hole clamp? My case is a 1/4 build. Thanks!

@IronCobraPTW

2 жыл бұрын

Yes

what size of corners , rivets, latches and handles did you used, Im planning to build a acoustic guitar road case. any advice of what to order will be appreciated Thank you for all your videos.

@reliabledan

6 жыл бұрын

Hope this helps. www.reliablehardware.com/roadcaseschematic.aspx www.reliablehardware.com/diyroadcaseparts.aspx

@Benny-con-amor

6 жыл бұрын

reliabledan thank you so much!!!

@TempleGuitars

Жыл бұрын

@@reliabledan One link say's 3/8" rivets, the other says 1/4" rivets. Which one is recommended?

Does the company make custom cases to order? I have a need for an amp head and 4U to 6U rack the would roughly measure 24"W x 23" H x 16" D without the lids

@reliabledan

10 жыл бұрын

Anthony, We do not make cases - we make case hardware for those who do. Search for "custom road cases" in your area.

@anthonyknight5114

10 жыл бұрын

Thank you. With those measurements in mind, could you recommend the the amount of tongue and groove valances and right angle extrusion? Is the stuff sold in 12' and 10' pieces?

@reliabledan

10 жыл бұрын

Anthony Knight You're going to need to a bit of work yourself. Start by making a sketch of your case that includes dimensions. This will aid you in determining the amount of valance, double angle extrusion and other parts you'll need. After you've done that you may certainly call and we'll help you refine your list. 800-757-5270

The ball corners are nice, but those are for the typical situation where the edge of the wood / corner is 90 degrees - what about if it's 45 degrees? Say I want to build an octagon box - what can I use to cover the corners?

@KidFromWinnetka

4 жыл бұрын

You might call Gene @ Reliable on Monday. He may have a suggestion for you. 818-753-8558

I'm putting together a shopping cart on your website to build myself a road case, but I can't find the corner clamps you use at the 1:15 mark. can you send me a link?

@reliabledan

6 жыл бұрын

Hope this helps - www.reliablehardware.com/large4holeclampzinc-1.aspx

I heard the size rivet to use but maybe I missed it, what length Rivets are you using?

@KidFromWinnetka

4 жыл бұрын

The rivet length depends on the thickness of the wood. Fow example, if your wood is 3/8" use 3/8" rivets. www.reliablehardware.com/poprivets.aspx

Distribuidor en México ?

How far apart are the rivets supposed to be on the double angle extrusion?

@reliabledan

6 жыл бұрын

Every 12 to 18 inches is ideal.

@beachndude65

6 жыл бұрын

Thanks, I'm building a lighting console road case :) I'll be in tomorrow for some more double angle :)

@reliabledan

6 жыл бұрын

Great - see you tomorrow.

What size of rebate?

como se llama aquello que parece una pistola.??? es una herramienta pero quiero saber com se llama

@sender87

5 жыл бұрын

remachadora

its the top of rivets when he's drilled them out off camera

Perfect

@reliabledan

5 жыл бұрын

Thank you!

about the ball corner clamp rivets at 1:06 - aren't you just riveting into wood with no backup washers? Won't that just crush the plywood?

@LostBushcrafter

2 жыл бұрын

also the latches at 3:12?

Can i ask what kind of hinges is that what do you called that hinge ? Thanks for the answer

@KidFromWinnetka

3 жыл бұрын

All hinges are here. Scroll down to Large Stop Hinge. www.reliablehardware.com/hinges.aspx

This video was riveting.

Where I can get all the material to bill one of those cases Info please Thank you

@reliabledan

5 жыл бұрын

www.ReliableHardware.com

where can i get some of those stop latches??

@IronCobraPTW

2 жыл бұрын

Tch

What size drill bit is needed to drill the holes for the rivets ?

@KidFromWinnetka

4 жыл бұрын

#11 drill.

@yuniormendez5953

4 жыл бұрын

Do you have the link cause the one I can find on Lowe’s is a 11/64

@KidFromWinnetka

4 жыл бұрын

@@yuniormendez5953 www.reliablehardware.com/drillbit-11.aspx

@yuniormendez5953

4 жыл бұрын

www.reliablehardware.com/3-legcabinetcornernickel-1.aspx What size extrusion should I get to fit on the corners 3/4” 1” ? Thanks for replying.

Nice tutorial! But you forgot something.. you need to tell people how to remove rivets that is placed wrong :)

How many mm the plywood

@reliabledan

4 жыл бұрын

3/8"

Price

Hi, I have 4- 24x18x119 4-in caster wheels ATA cases for sale. Do you know anybody that might be interested in buying those?

You are using to many rivets with your hybrid. Also those extra base rivets shoud be in line with your lid rivets. Why are you not using bar clamps ? It's like basic and much better than a belt. Overall not a really good job...

So I watched 8 of 11 where did 9 10 &11 go?

@KidFromWinnetka

2 жыл бұрын

kzread.info/dash/bejne/pmpttNlwgryTZrg.html kzread.info/dash/bejne/gqlku8ipdt3IYcY.html kzread.info/dash/bejne/gXmuqaV-g9yqgbw.html You're welcome 🙂

Good joob...he he he

15 inch 4 top ka cabinet 2 15 inch bass cabinet him KO chahiye apka number chahiye humko

:-)

the rivets on the lid and the case dont line up ,,, why not ? 0:27 lid rivets in the way of the balls ,,, its only half thought out , you need to plan ahead more ,,, still if its still gigging eight years on , who cares , its the only one of us that is.

Li

You guys are screwed up.

:-)