Great video. I've always found it frustrating that there isn't a good way to test injectors other than a buzz test or having a dealership with an IDS do a cylinder contribution test. I never thought to use a temperature gun to take measurements at the exhaust ports. That could be a great way to narrow down a failing injector without spending money on a contribution test, especially when you have no codes. Thank you for posting.

Great tip on identifying by manifold temp.

Awesome video! No bs Bottom line topics overviewed very well with links provided for more detail. I'm really surprised this hasn't been viewed WAY more. Thanks for a great video👍🏼👍✌🏼✌🏽

Very good info Thanks for sharing your products look good I'm going to look further into them.

Very helpful and informational video. I checked out your website too and it's very nice as well with very well done guides. I plan on diagnosing my truck's issue soon when the weather cools down (it's not a daily driver). A ODBII scan gave me a faulty GPC module, I replaced that but I'm still getting smoking, and a smell, not quite like raw diesel but maybe a burning carbon like smell? Anyway, I'm fairly new to diesel troubleshooting so any suggestions would be greatly appreciated.

I have a 2003 f250 6.0 diesel it shows four injectors not contributing , runs alittle ruff will replacing the o-rings fix it as long as the wires are ok

When you say manifold ports, you mean exhaust manifold?

My last oil change was horrible black sluggish engine oil ? Can I flush the 6.0 engine oil ? And with what ? I think one of the injectors is clogged

I need some help with my 6.0 powerstroke. Have a 6 inyector circuit low. If you can help me wich are the more common causes of this code and also it have EGR P0401 code. And P0404

tell me.The voltage on the module is 48.5, on an idle engine, and the injectors are not tested!

How mutch for a injector Ford f 350 2006

How do you keep them to last? What can I do to prolong replacment? 2006 6.0

@dieselcare

2 жыл бұрын

Hey Miguel, our recent video is a response to your question. If you have any additional questions, call us at 1-800-961-9290.

so i have no hard start idles fine but dies on me when i drive down the road runs ruff then won’t start for 10 min any answers

@adamslape5963

Жыл бұрын

I have this same issue any luck with what was wrong

@creepyfriend1999

9 ай бұрын

Hpop leak more then likely does it have a long crank to start back

When I am at certain speeds of between 30 or 40 or 70 to 80 mph, my truck acts like it is choking or an old steam engine puffing with black smoke exiting the tailpipe. It does not do this all the time but has been gradually getting worst. There are only 148,000 miles on the truck. I have changed the fuel filters a couple of times now too. Just frustrated about finding a solution.

@terryslay1

2 жыл бұрын

Did you ever figure it out? Mine has similar miles and symptoms.

@williamshultz3598

Жыл бұрын

Sounds like you're FICM or Fuel Injector Control Module is starting to have issues.

@toddmiles3875

Жыл бұрын

@@williamshultz3598 That’s what was causing the problem. Replaced it and my truck runs great again. Thank you!

@courtneybattle4983

Жыл бұрын

Did you fix your issues Todd?

@Julio860JVL

Жыл бұрын

@@courtneybattle4983 yes if was the FICM.

Wth does he mean at 6:08ish by "pick a cylinder that's easy to get to cuz you're gonna have to spend extra time w/it"? Wouldn't you be cleaning a cyl that the engine picked to die? I mean a guy doesn't usually have any say over it, I just fix whatever it decides to shell out. Js

@asdf9890

Жыл бұрын

He may mean to start with an easy one if you're doing them all.

This is nonsense.

@patrickwelch620

Жыл бұрын

No diagnosis om the injectors whatsoever. Wasted time watching this.