Thanks for the info man. I figured I was going to have to replace my wastegate since it was sprung way to hard for my application.

Nice video, I have a feeling I'll be doing something similar soon. Thanks!

Really great idea. I have a similar issue with currently hitting around 10psi and I'd like to drop it to 7 to 8 until I can get everything properly Dyno tuned. I'll be trying that this weekend.

@BuildingTheEXOCET

4 жыл бұрын

It works. Just buy a few different springs to test it out.

This is awesome! I’m close to initial startup of my L28ET 240Z with some protunerz goodies and a maxpeeding rods T3 billet turbo, I’m very skeptical of the wastegate that came on the turbo so I’ve enabled boost cut on my standalone for 11psi. If this mod really does help you are a genius and I owe you a beer 😂

Definitely trying this!

Great solution....! Thanks

If you don't preload the actuator so much then you don't need as much spring assist like you're using. It should be minimal preload on the rod usually.

excellent

Muchas gracias 🙂

gotta port my wastegate but this might help me out a bit

I'm trying to run twins on a all stock motor I need them both to open around 2 psi lower the better not doing it so much for the hp more for the experience.....this is the best I seen about this subject

should i just put my old working actuator on new turbo?

Great info. I wonder if you got a stiff enough spring you could get it down to 2-3 PSI. I'm going to be turbocharging an old carbed motorcycle soon and I'd like to keep the pressure low.

@BuildingTheEXOCET

4 жыл бұрын

It's possible but that's pretty dang low of a number to hit

Making a Spring clip instead of a spiral spring can be installed without removing ghe wastegate

I would be worried about the wastegate not closing fast enough after it opens.... Exhaust gas keeping it open because there isn't enough spring pressure to close it

@BuildingTheEXOCET

4 жыл бұрын

I think that's a reasonable worry. I did not have this issue at all and I ran this hard for a year at autox. I'm on a new turbo now, but someone else bought this one and still runs it

Hello. What length is the spring? I’m wondering if a 6lb.recoil spring from a glock would fit properly. I have a gt28 turbo and I don’t want boost pressure rising over 7lbs.

@BuildingTheEXOCET

3 жыл бұрын

Can't remember. Sorry

It's okay to lower the boost without tuning? I just bought an eclipse that runs 28psi. I need to lower it for now because I'm not comfortable with it

@corneliofehr8001

26 күн бұрын

Kinda late, but it will be fine. You'll lose power and it will run rich, most likely

Hey, I'm about to do this to my turbo which is the same as yours. Is the boost pressure typically "read" when the wastegate flapper is completely opened, or is it the pressure when it is cracked open?

@BuildingTheEXOCET

2 жыл бұрын

It should be read all the time. The max boost should be where it holds when the gate is completely open. If you have the same turbo as me you will need to port the wastegate opening quite a bit. This just allows you wastegate "flapper" to open sooner to bleed the pressure off quicker. Mine stock was not opening completely until like 15 psi so I ported the gate opening in the turbo then added this spring in order to make it open sooner.

@MotorMonks919

2 жыл бұрын

@@BuildingTheEXOCET sweet, thanks for the reply. I’ve seen your other video as well, I gotta port mine too

@dennisrobinson8008

Жыл бұрын

Was it obvious how much the opening could be ported?

@MotorMonks919

Жыл бұрын

@@dennisrobinson8008 Yes. It was pretty simple. Still using the same turbo with no boost spikes!

@dennisrobinson8008

Жыл бұрын

@@MotorMonks919 I appreciate the feedback. I guess it really works and will implement the same.

Did you do the tuning yourself?

@BuildingTheEXOCET

4 жыл бұрын

Yes I did, if you can call it tuning. Basically just tuning arf and ve tables in tunerstudio.

You do realize you have to plug your air gun with your finger when you're adjusting your air regulator , correct?

@BuildingTheEXOCET

4 жыл бұрын

Not if you want the correct flow reading. By pulling the trigger on the gun and measuring the flow going through the meter it shows the actual flow when it's being used.

@BEANS-O-MATICtransmissions

4 жыл бұрын

@@BuildingTheEXOCET but you're not measuring flow, you're measuring psi. That's a dead end test into a waste gate, not flow. Re do the test starting at the lowest setting on the regulator, remove the blow gun and attach the WG. Increase pressure while measuring rod movement.

@LMSILVIA

3 жыл бұрын

@@BuildingTheEXOCET YEAH air does not flow through the actuator, if it is then it has a punctured diaphragm. I see that when you pull the trigger there is a sound of air rushing out of where?

do you have any link for the spings please?

@BuildingTheEXOCET

2 жыл бұрын

I just got some at ace hardware

@V-Angel

2 жыл бұрын

@@BuildingTheEXOCET and the dimention you used?

Don’t they advertise it to be 8lb from factory! Wow it would blow the motor or creep to death in this case

@BuildingTheEXOCET

3 жыл бұрын

Yyuup!

@BulliKid

3 жыл бұрын

@@BuildingTheEXOCET that’s messed up. Any way to pull the metal o. The actuator a little away so the spring is not S tight in there

@mopedman666

Жыл бұрын

I have the exact same actuator off a Chinese turbo. Mine opens at close to 30 psi. This junk was advertised as 8

My wastegate work in the opposite way, on vacuum.

Chinese? Then it is junk.