4x4 Transfer Case Input Seal Replacement
Автокөліктер мен көлік құралдары
#4WheelDrive #TransferCase #AutoRepair
An easy repair for either preventative maintenance or otherwise.
If ever you have your transfer case out for any reason, it’s always a good idea to change the input seal.
This particular transfer case is out of a 2014 GMC Z71 4x4
Пікірлер: 54
center punch seal then screw in a deck screw, grab screw head with vice grips on slide hammer works too
Ha you make it look so easy. I just had trouble peeling off the inner seal of a new ketchup bottle. 🤣
@EJsGuitars
4 жыл бұрын
Those can be tricky!🤣👍🏼 Thanks for checking it out my friend!😁
When I changed the seal on mine I went the long way around the barn and pulled the retainer Wish i had seen your method first. I'm gonna try this on my S-10 since the retainer is flush with the with the face of the transfer case and has a butt load of black RTV holding it in place. I'm thinking nothing short of C4 is gonna get that plate outta there. Thanks for a great how to.
FYI, that is a pvc slip joint or compression coupling, repair coupling, or dresser coupling, called by multiple names just to make it more difficult lol, made in multiple sizes and sold at most box stores or your local plumbing wholesaler...
Great job, EJ !!
@EJsGuitars
4 жыл бұрын
Thanks my friend! It’s how I buy music equipment.😎
I used this same trick on an overhead cam seal. Works real well.
Little tech tip grease the drill bit, collects most of the shavings:)
Thankyou for the video. I’m going to be replacing the rear main seal and doing the gm Transfer case pump issue repair. I believe this is decided me I’m going to do the seals as well. The truck has 170,000 on it I’m sure it’s due
That's genius getting that seal out :)
@EJsGuitars
4 жыл бұрын
Works great! Thanks for checking it out my friend!
EJ aka Transmission Dr Guitar Badass !🤪 TFS Enjoyed because you're doing the work and not me LoL
@EJsGuitars
4 жыл бұрын
Lol! Thanks dude! You’re the real rocker!🤘🏼
This is probably a good strategy for the front output seal as well
nice work ! guitar play too !
@EJsGuitars
4 жыл бұрын
Awesome! Thanks!
Clever way to get the seal out-also great idea of using the pvc pipe to tap with the end fitting to make sure you have a flat surface to tap in the new seal.
Practice that sweep picking 😃
Nice job! Question, do you also have a easier way or trick to replace that very difficult front output seal, the seal for the front the 4x4 front driveshaft, the two-piece seal! Thanks.....Sorry, for the 263hd transfer case!
so cool
@EJsGuitars
4 жыл бұрын
Thanks Rick!
I just tap it in at 12 o clock and it pops out at 6o clock then pop it out with a screw driver.
Hi, can the transmission atf go to transfer case from a bad seal?
@BuddyHolly58
3 жыл бұрын
Yes it can. I had it and destroyed my 4L60e
Did ya get that piece of pipe from the Snap-On guy, or the Mac guy???
@EJsGuitars
4 жыл бұрын
I think we got it from Sanford & Son
Great video, where did you buy the adapter for the slide hammer?
@EJsGuitars
2 жыл бұрын
Snap-On pieced the whole setup together for me. Everything is Snap-On as far as the slide hammer goes
Ej ... sup brother 🙂🙏 like 5 Praying for you
@EJsGuitars
4 жыл бұрын
Thanks Steve...I need it
Replacing my 4l60e, noticed it's leaking big time right where the transfer case and tranny connect and old trans lost a majority of it's fluid there, soaked, do you think the paper type gasket could be the culprit? Or would the seal your replacing here be more likely the problem?
@EJsGuitars
2 жыл бұрын
If the transfer case is over full the the front input seal is bad. But that wouldn’t cause an external leak. The gasket is most likely the issue
@BeAsTB207
2 жыл бұрын
@@EJsGuitars the transfer case was checked and had normal amount definitely not overfilled. Overtime my truck was leaking there eventually driving it said transmission was hot and I lost 3rd and 4th and looked underneath and it was soaked right where they meet up and my trans was about out of fluid. Would you recommend going with the gasket or something like Rtv ultra grey or something rather? Just want to seal it up properly so I don't run into this problem with the new transmission
@EJsGuitars
2 жыл бұрын
Gasket only. Gasket is best, and do not add silicone to the gasket. You can use silicone by itself but the gasket is the best option
@BeAsTB207
2 жыл бұрын
@@EJsGuitars Thanks for the response. I figured it would be one or the other. Will probably get the gasket if the local auto parts store has it, if not silicone it is! Appreciate it. First time attempt tackling this type of job.
@offroadoutlawsmafia9277
3 ай бұрын
@@EJsGuitarsI actually came here because I’m having a problem because of that dude who owned the truck before me used silicone and didn’t do it so well
Where did you bought the slide hammer?
@EJsGuitars
2 жыл бұрын
Snap-on
@julianortiz699
2 жыл бұрын
Thanks it worked brotha 👍👍
My apology It looked like it had bolts holding the plate on ! Leave it to chevy to create something a pain to repair !
I w ould simply take off the bearing retainer plate !
@EJsGuitars
3 жыл бұрын
Uhm, that one doesn’t have a bearing retainer plate sir...some do, but not this one. Thanks for checking it out though
I just use a Dremel.
@EJsGuitars
4 жыл бұрын
If all else fails, get the dremel!🤘🏼
@PooNinja
4 жыл бұрын
EJ’s Guitars if that fails Sawzall 🤘🏽
Sir. Those safety glasses on your hat while youre drilling metal wont help when not on your face. Just saying
That drill is crap
@EJsGuitars
3 жыл бұрын
Lol! I know, right?
Just buy toyota they don’t break 👍🏽😂
@rockerpat1085
4 жыл бұрын
That's why Toyota dealerships don't have large service department's!!! Keep Rocking!!!
@PooNinja
4 жыл бұрын
Rocker Pat Just for recalls and car washes because somebody sold them bad parts and they do get dirty😂
@EJsGuitars
4 жыл бұрын
Didn’t y’all see my other video of me pulling the trans out of a Lexus? 🤣🤣🤣 But y’all are right Japanese stuff is rock solid, that’s why I drive Nissans.🤘🏼
@PooNinja
4 жыл бұрын
EJ’s Guitars GTR mmm