Try lubricating from the inlet to flush out the water on the air tools before they rust up.

@CrabTree1

Жыл бұрын

Thanks for the tip. I will definitely try that.

@winclark7686

Жыл бұрын

😢❤❤

@andrewburridge2955

Жыл бұрын

Any of the stuff for sale.. and where are u ???

@user-ht1xu4gv2u

Ай бұрын

​@@CrabTree1scoreeee😅😅😅😅 especially air tools somre WD. 40. And good as new

lube the air tools generously. Now. There is an air tool oil. It goes in the air input. Its recommended to lube the air tools before each use. Great deal on that pallet. That craftsman air ratchet is 70$ new. It will last a lifetime if you take care of it. Mines 45 years old and i just used it today.

Nice, that dovetail joiner is 3 times the price you payed. 👍

🎉 after going to auctions and every other kind of sale the last 20 years my grandkids and kids are going to need at least six months just to go through my stuff after im gone,and im still buying ju stuff

45$ bucks plus the 100$ premium. Got a killer deal on a paint sprayer last week but didn't realize the 100 dollar minimum. I am usually buying military generators with a 15% premium. Looks like you did pretty good on this one

@CrabTree1

Жыл бұрын

yep gotta be careful with the premiums

NICE Pallet.

I wouldn't mess with the outboard too much until you get that bottom end in the water so the water pump impeller is lubricated with water. If you don't you'll ruin it. As far as the rest of it goes it wants to run. Pretty much the only thing that goes wrong ith them is the water pump impeller goes bad, the coils go bad, the carbs gum up and they set up from rust. Don't run gas with ethanol in that motor unless you put the ethanol kit in the carb. It looks like a less than 10 hp mid sixties motor. The pull start mechanism on those were a pain and if I recall are pretty hard to come by. As for the air tools there's only a few moving parts in them. There's vanes that come out of the rotor some bearings and the mechanism on the working end of it. If you don't get some oil in them soon you'll ruin them. Marvel Mystery oil works as well as air tool oil. I'd flood them to get all of the water out and then 2 drops a day is all they need. Ya done good for $45.

Cool, great deal !

Watching your video in Scotland a great bargain for 45$ keep up the good work

@CrabTree1

Жыл бұрын

Thanks appreciate it

A challenge that wins with a fine vintage motor. Onward!

Great deal!

Snowblower may meet some shoes relatively inexpensive also scraping edge also replaceable

Yep, just put a few drops of air tool oil down in the air inlet and run, they’ll be fine.

That old 9.5, possibly a 9.9 hp Johnson or Evinrude we’re good motors. Very reliable. Most were 9.5 but supposedly some were actually 9.9hp just before they changed the entire design to the more square/rectangular engine housing.

@CrabTree1

Жыл бұрын

Cool thanks for the info. I looked into and i think this one was a 9.5hp

@johnharris7353

Жыл бұрын

I had a 9.9 Johnson like that.

You made out like a bandit on that pallet. Just the motor on snow blower was worth more than pallet. Plus air tools that need some tlc and me unless I had a small boat. I just sell the boat motor for what ever

@CrabTree1

Жыл бұрын

Ya your right. I’ll probably just sell the motor as is.

@CrusaderSports250

4 ай бұрын

Fix the motor up and buy a boat for it😊. You did good on that pallet, loved the snow blower.

Spray some oil in the air hookup on those air tools, they pickup a good bunch of power just from that alone. Plus airtools should have a bit of oil dropped into them occasionally. You say are breaking a bolt loose and its trying but struggling, put a few drops of oil in the tool and bang, bobs the uncle. For some reason, all boat motors sell for good money when they run... I believe this one will come to life again. Even so, parts for older motors are now reaching some crazy high dollars. That big grinder hand held here in alaska, is around three to five hundred dollars depending on brands.. the cheapest you find are garage sales as you go to a pawn shop thinking its a great place for a deal and then know they should of included vaseline with the sale.

@CrabTree1

Жыл бұрын

Awesome thanks for the tips.

@firesurfer

Жыл бұрын

At least at the pawn shop, you don't have to go to the doctor for a checkup anymore.

The snowblower engine looks like a Tecumseh Snow King engine. That engine alone is worth more than what you paid for the pallet by at least 5 times.

That new dovetail joiner jig is about $150 + new like that.

@CrabTree1

Жыл бұрын

Ya I gave it to my brother who is into wood working he was pretty happy lol.

The Dove Tail jointer needs the Carb cleaned as well.

you got at least ten times your moneys worth! Good job!

@CrabTree1

Жыл бұрын

Yes! Thank you!

The sound of the one right at 20:00 was so iconic I'd almost pay for a gun that made that glorious sound whether it actually worked or not.

@CrabTree1

Жыл бұрын

definitely sounded healthy

That snow blower carb needs the jet pulled out and the Jet needle pulled out and the little holes cleared. Then it will stop surging. It is an easy fix. Well if it is not too far gone like one I did a while back for a guy in the military. It was so bad I had to replace the carb.

@CrabTree1

Жыл бұрын

Thanks for the tip. I will look into it further in the fall

SCORE! Just subscribed!

@CrabTree1

Жыл бұрын

Awesome thanks

As for the boat motor, a clean plug and clean the float bowl of the carb

@CrabTree1

2 күн бұрын

That's the plan!

Wd 40 soak the air tools maybe salvageable

wonder if that motor gonna work hahaha .. I just picked up a 4' fan needs a motor :)

@CrabTree1

Жыл бұрын

I have a feeling it will just need a carb clean and it will fire right up.

I was waiting for the boat motor to catch just enough to spin the drill off and smack you in the chops.

Lube the airtools internally with PB Blaster

@CrabTree1

Жыл бұрын

Definitely will try that. Thanks

check the shear key as it started and loosened the flywheel nut

@CrabTree1

Жыл бұрын

Thanks I’ll check it out.

@TheSynthnut

Жыл бұрын

Yep, was about to say the same. Had a number of Briggs that refused to start and had managed to shear their keys and so, despite the apparent strong spark had waaaaay out timing!

@CrusaderSports250

4 ай бұрын

​@@TheSynthnuthad a Villiers with reversing dynostart that used to do that, most annoying, never went anywhere without spares, problem was a big heavy flywheel rotor and a worn or damaged taper, so it would never be good., but it was transport most of the time😊.

You need to put a pull rope on it! When it pops you let go of the rope. I don't think you can get the drill off fast enough. Good luck with the bat motor. The old ones are more durable than new ones! Eddie

@CrabTree1

10 күн бұрын

yes sir

This is my kind of tools 🔧 old like me 😂😂😂😂

Jerry can has a bendable end so you do not spill. Sheesh. Wow.

@CrabTree1

10 күн бұрын

Yep iam a not the brightest lol

18:36 probably the switch

Air tool oil up the air fitting...they'll be good as new. Sell the boat motor. It'll need an impellor, propeller, and carb rebuild.

@CrabTree1

Жыл бұрын

Great idea

not bad at all for 45 bucks

@CrabTree1

Жыл бұрын

Yep I thought it was a deal.

Make it run

Hit the air Tools with lube now to stop the internal rust.

Your comments are great

@CrabTree1

Жыл бұрын

lol thanks

You got your moneys worth on that bench grinder alone.

@CrabTree1

Жыл бұрын

yes sir

What is the story of the t bird and what are your plans for it?? 73 dan

@CrabTree1

Ай бұрын

It was a garage find that had been sitting for 15 20 years, i bought years ago and got it running and driving. Still runs and drives but i only take it out once in a blue moon lol

il and run the air tools

I'd try to fix the boat motor but I'm retired ,

Boat motor turns over there hope for it possibly needs magneto cleaned up

@CrabTree1

Жыл бұрын

ya ill probably clean the carb and try again

There goes the water pump. No water pump brakes

@CrabTree1

Жыл бұрын

Iam sure the pump was no good from the get go and needs to be replaced

My question is what kinda motorcycle is setting there gathering dust and dirt. I hope it's not a Harley Davidson.

@CrabTree1

Жыл бұрын

lol no it’s a Honda shadow 1100

@CrusaderSports250

4 ай бұрын

​@@CrabTree1saw that as well. You got some other interesting stuff there as well.

Didn’t know Richie brothers sold this kind of stuff

@CrabTree1

Жыл бұрын

Yes sir my local Ritchie Bros has all kind of random stuff

@CrusaderSports250

4 ай бұрын

​@@CrabTree1sounds wonderful 😊.

Get that outboard motor running and sell it

@CrabTree1

Жыл бұрын

Still debating what I should do. If I get enough comments I’ll get it running.

@CrusaderSports250

4 ай бұрын

​@@CrabTree1definitely running, if for no other reason than it's worth more like that, but you know you want to hear it😊.

There is nothing at Richie Bros less than 100 dollars. If you win a bid for $20.00 dollars they add on 100.00 for each lot you win minimum plus another buyers fee. I won a 20 pallett that cost me 100.00 plus 8.00 plus the 20.00 dollar bid. so 20.00 turned into 128.00 dollars. Then you will need to schedule a time to pick it up.

@CrabTree1

3 ай бұрын

yes sir you are correct

you need a pressurized gas tank with a squeeze bulb.

@CrabTree1

Жыл бұрын

Ya that was the next step

You could probably get away with using half the torque you put on those plugs. 15-20 ftlbs is more than plenty. But hey, at least you know they're not going anywhere. Lol

@CrabTree1

Жыл бұрын

It’s a high HP motor gotta make sure they don’t fly out lol.

How about you snowboard and brand new takes four or five pulls to get the things to go

@CrabTree1

2 күн бұрын

ya i was surprised

Fix the out board motor

Wd 40 in a bucket

Just the benchgrinder was worth more than 45$.. amazing deal if you dont have thumb in your ass. Blower alone would be 100$ even if it didnt run. Also please make starter free turn tool from ratchet or one way bearing. If you dont do start with the drill just right you risk on getting slammed into face with it or breaking your wrist. One way bearing will ensure engine can out run the drill when it starts.

@CrabTree1

Жыл бұрын

Thanks for the tip

PUT THE AIR HORN ON THE THUNDERBIRD. LOL

@CrabTree1

Жыл бұрын

lol that would be awesome

dont be turning that out board over without grounding spark plugs or the wire if you turn them over without grounding you can ruin the coils this motor could be anywhere between 3 hp up to 9.9 im thinking its closer to a 9 hp i have two of these one is now running haven't finished the other one yet also used puller to pull flywheel if necessary clean and set points for 20 thousands clean carb low speed and high speed jets could the air screw mixture count turns till bottoms out lightly and remember this when you put them back you will come back out to close the turns in you did in reverse

@CrabTree1

Жыл бұрын

Thanks for the tips

@CrabTree1

Жыл бұрын

Ps motor is a 9.5hp

The handle has a start position on it

@user-uh6oy3zu8g

3 күн бұрын

Boat motor haandle

@CrabTree1

2 күн бұрын

YEP Saw that

tools and their proper care are not your strong suit, little Air tool oil before you forced all that water thru might of helped, if let them sit to long after not doing trying see if they work Thel be just locked up rusty tools, little preventive action on your 45 score, could go a long way for tools if you hand any intensions on using or resaleng.

@CrabTree1

Жыл бұрын

Don't think Oil would have help until all the water was pushed out first

😮 those poor air tools. Oil is your friend

@CrabTree1

Жыл бұрын

Had to get the water out somehow oil was then used afterwards

Why do you keep thinking the outboard motor will run without fuel?. Soak all of the wet air tools in diesel fuel for a while to free them up.bShoot PB blaster in the air inlet and let soak.

@CrabTree1

23 күн бұрын

Fuel was sprayed in the carb

SPRAY OIL IN AIR CONNECTOR FITTING

@CrabTree1

Жыл бұрын

yep added a couple drops for oil to each

You were spending the boat motors the wrong way

@CrabTree1

10 күн бұрын

Nope definitely was not. But thanks for watching

sander

Buy a "no-spill" brand gas can, it will change your life I promise you.

@CrabTree1

Жыл бұрын

lol ya definitely will check those out thanks

@johnsmith7676

Жыл бұрын

Junk.

@litz13

Жыл бұрын

You can also buy spouts for existing cans that don't have the stupid contortionist valve crap on them

@CrusaderSports250

4 ай бұрын

​@@litz13or just a funnel.

It isnt hooked up to any fuel.

@CrabTree1

23 күн бұрын

I sprayed fuel in the carb

Oil

Not much that you're going to throw away then. Some of it isnt worth storing or fixing.

@CrabTree1

Жыл бұрын

Storage is free and it was worth the money just for the excitement of seeing what was inside lol

Looks like you paid $45 to take out there trash ha ha !!!!

@CrabTree1

Ай бұрын

lol its always a risk at the auctions. but not this time

What you are calling a polisher is an angle grinder. You don't have a clue

@CrabTree1

Жыл бұрын

No its a automotive polisher. but thanks for watching

@buck3409

Жыл бұрын

@@CrabTree1 LOL. It's an angle grinder with a buffer wheel on it. Will run different.attachments

Quite showing your face

Bunch of junk to be hanging in the shop taking up space.. Just let it go Scrap it. Waste of time and money. Value zero.

@CrabTree1

Жыл бұрын

Thanks for the comment and view. Each to there own

redneck scratch ticket right there.

Clean the stuff up and make money off of that.

@CrabTree1

Жыл бұрын

Outboard is already sold for $150