📦 PRODUCTS IN THIS VIDEO 📦 • DeWalt Screwdriver 40-Piece Bit Set, Impact Ready (Paid Amazon Link): geni.us/LA9a2h​ • Horusdy 208-Piece Screwdriver Bit Set (Paid Amazon Link): geni.us/fjeGe​ • DAP Tank Bond Liquid Grip: bit.ly/3dHVPWK​ The Amazon links above are affiliate links, which means you pay the same price as always but we make a small commission, which helps out our channel - so thanks!

@davebower8810

Жыл бұрын

Amazon links are not working...

@Eddie-yc5yd

Жыл бұрын

It's like liquid sand. Learned something today.

@puppetmaster3371

Жыл бұрын

Bad links.

@hussaincader4899

Жыл бұрын

Soap mould

@csehszlovakze

Жыл бұрын

PZ screws have PH obsolete around here.

My number one tip is to not use Philips heads in the first place.

@gtbrown4840

Жыл бұрын

Yea me to i bought the torx screws by accident lol once i tried them i nev buy phillips again

@darwinbodero7872

Жыл бұрын

Based comment

@Q..J..

Жыл бұрын

Unfortunately most things you buy that contain screws - have Philips screws. I hate them!

@DiligentDave1966

Жыл бұрын

@@Q..J.. You can find Torx in the same lengths as phillips.

@Q..J..

Жыл бұрын

@@DiligentDave1966 sweet!! Thanks for the info., checking them out now. 😊

That tank bond stuff really saved me on a hard to reach rapidly stripping screw. After several minutes of carefully driving this cabinet screw at an awkward angle, I stopped when I realized it was stripping, watched this video and went out and got this stuff, and finished the screw in about 30 seconds. I could have saved a bunch of time if I had this from the beginning. Thanks! Good stuff.

That was probably the smoothest transition to a sponsor endorsement I've ever seen. Smoooooth.

Probably the most important tip is to make sure your bit isn’t worn. Every time you let it slip you are wearing some of the bit off. Soon even the correct size bit will constantly slip. Replace them often. They are cheap

@connerphillips1228

Жыл бұрын

One of the best things I ever did tool wise is buying a 30 or 50 pack of assorted bits. Always easy to find the right one and no quibbles about tossing a bad one.

@Healcraft

6 ай бұрын

not usually the case in my experience except on the cheapest of bits, usually they are all much harder than a screw

Good tips. A few more... Drill the correct size pilot hole, especially in hard woods or when using small screws or soft metal screws like brass. Apply some wax to the threads before inserting, I keep an old candle nearby just for that purpose. Also, watch your speed when driving screws so you have more control when driving.

@Micro-Moo

Жыл бұрын

Good idea. It does work. Some kinds of wood, for example, give enormous friction.

@janami-dharmam

Жыл бұрын

Instead of wax, a bar of soap or a drop of liquid soap is also useful. soap will not interfere with subsequent painting or other type of finish.

@Micro-Moo

Жыл бұрын

@@janami-dharmam When I faced extremely hard and viscous wood, I naively sprinkled some WD-40 in predrilled holes, it was the first thing to come to my mind. It helped me. What do you think about it?

@OlTrailDog

Жыл бұрын

I drilled a large hole in the bottom end of my finish hammer handle. I fill this with bee's wax (toilet ring). Note: if you drill a small hole that intersects the end of the handle hole it will allow air to escape as you fill the bee's wax hole easier. This way I had wax at the ready for both nails or screws. In addition, I would melt some was and keep it in a tin in one of my tool boxes for either refilling my hammer handle or for poking screws into when needed.

@Micro-Moo

Жыл бұрын

@@OlTrailDog It's not a good idea to drill or embed anything into a hummer handle, it badly weakens it. This part should be solid and smoothly shaped as much as possible.

Tank Bond is basically engine valve grinding/lapping compound. So, if your local auto parts store is close by, you can get that stuff too and it's identical. Valve lapping compound is used to grind away the valve and seat surface of a valve that is old and either pitted from heat or pitted from rust. It restores the full contact band needed to seal. It's basically liquid sandpaper. 👍

@michaelhutin5451

Жыл бұрын

Thanks, I'm sure lapping compound is cheaper.

@harrycaul2494

Жыл бұрын

Nice tip. Can at a push use superglue and bicarbonate

@RingZero

6 ай бұрын

@@michaelhutin5451 - No its not 🙂

@you2tooyou2too

4 ай бұрын

@@harrycaul2494 Sodium Bicarb is quite soft. That doesn't make sense. Fine pumice or some Silicon carbide (SiC) powder/granules does. PS The real problem is extracting 'stuck' screws, in that placement pressure helps drive it in, but fights pulling it out.

@jpdemer5

2 ай бұрын

@@you2tooyou2too Bicarb just causes the superglue to harden very quickly. Makes sense if you want to glue the screw to your driver, but that's pretty unusual... maybe an option if you need to place a non-magnetic screw (like brass) in a tough-to-reach spot?

Pre-drilling is also a good tip.

@LRN2DIY

3 жыл бұрын

Great point - I'm a huge fan of pre-drilling in general to avoid splits and cam out.

@Micro-Moo

Жыл бұрын

@@LRN2DIY True. I thought you would start from this tip.

@motoryzen

Жыл бұрын

Indeed. Also use a counter sink tool to hammer a few hits on it to start a tiny hole. This will guarantee your drill bit doesn't dance around the spot you want it to truly begin a new hole with. 😁

@mr_killjoy4205

Жыл бұрын

@@motoryzen "automatic center punch"

@motoryzen

Жыл бұрын

@@mr_killjoy4205 indeed. One name for it is a nail punch or nail setter.

Excellent video. The Tank Bond idea is new to me. However, *torque* is specifically a turning or twisting force, not the downward pressure. Applying the downward pressure might help you to apply more torque, but the downward pressure is not torque.

Good tips for north American soft wood, but if using Australian hard wood pre-drill. If the wood smokes when drilling add soap to thread. Also avoid cheap screws, like ones that came with hinges,etc. Cheers

@rangars1

10 ай бұрын

You nailed it😄👍🏼 at times even drill bit struggles to get through the hard woods.

I just became a homeowner last July and I’ve started to dabble in DIY. I’ve made the mistake many times of stripping screws. Thanks for the video! You saved me some frustration!!

Wow! Never heard of tank bond. Thanks!

Great info , thanks for sharing. Right to the point with no BS music or self promotion nonsense. Very informative and I learned a few things I didn’t know. Thanks again liked and sub

@BeatACVR

Жыл бұрын

1:30 merch ad

THIS! This is the kind of information I've been looking for! Thank you :)

A wide rubber band works as good as the liquid grip and you can use it over and over again. If you’re driving tons of screws just keep a couple on you wrist. The best part they cost like 2 cents. 😁

@sterlingroberts6240

Жыл бұрын

Solid, thanks!

Thank you so much. That's very helpful I wondered why those screws get stripped.

Thanks for the info on the DAP products, Nils.Very well organized!

Very useful instructions, thanks.

Excellent tips. Not knowing about Tank Bond Liquid Grip.

Liquid grip seems to work the same as valve grinding compound. Thanks for the tip.

Depending on the timber, I also drill a pilot hole to the inner diameter of the thread. I also apply beeswax to stop binding. This is a must if you are using brass screws.

@PR-bd1ky

21 күн бұрын

Can you explain in more detail "drill a pilot hole to the inner diameter of the thread"

@J.o.e_K

20 күн бұрын

​​​@@PR-bd1ky select a smaller diameter drill bit than the diameter of the screw you are using. Drill the hole first. Then place the screw in that hole and screw it in. It goes in much easier and also prevents the wood or deck material from splitting. You must use a smaller diameter drill bit otherwise the screw will have no material to bite into. The smallest bit that allows the screw to go in easier but still gets a good bite and hold into the material.

@channelsixtysix066

19 күн бұрын

@@PR-bd1ky OK, use a drill that is the same size as the screw shank. So if the screw has a 3.00 mm shank then use a 3.00 mm diameter screw.

Bro you have a really great channel here. I just found you recently And wow you have so many informative videos. I already follow and watch a lot of tool and DIY related content but you but you have provided education in areas those channels havent. Thank you!

Excellent bit of knowledge.

I thought I bought the wrong kind of drill. I was using the wrong Phillips head, I had a pointy one and didn’t need it. Thank you! Teaching me things I shoulda learned a long time ago.

I was trying to remove a fairly small, but long Philips head screw with my drill. It was in an awkward location and I ended up stripping the head. An experienced carpenter got it out using an impact driver with a square head bit. Pretty amazing.

Ty for sharing tank bond will def try!

Very helpful 🤘🏼💯

Thanks you for for tips 💯

The DAP product looks really good. Thanks

Great tips! Well done!

Wow. Thanks a million!!

Great to explanation and fixes😎👍 I use poly grip to get stubborn screws in and out. Can’t figure out why it smokes 😱

There are several videos showing the relatively new Makita impact xps bits. They seem to fit insanely well. If you absolutely must use phillips screws, I would recommend giving them a try.

Tnx for ur useful guidances.

I would suggest pre-drilling holes, especially in harder woods.

Wow, I'm glad to know about this too; I'll buy some now if I can find it!

Good info. I took a course in fasteners years ago when I was going to school for manufacturing engineering (never finished that degree, but got 2 in welding). My instructor was adamant that when the screw head was damaged it was “cammed out”, and “stripped out” referred to the threads being damaged.

@LRN2DIY

3 жыл бұрын

That's accurate. I thought about using the term "cam out" but opted for "strip" since that's what more people know it by. I usually call it a stripped screw head too - I should probably start using the right term 😂

@knifetex

3 жыл бұрын

@@LRN2DIY Haha. I gave up years ago. Same thing with widescreen TVs. People call them 16 X 9, when in fact it’s an aspect ratio of 16 : 9. I just thought I’d throw it out there for the heck of it. 🤣

@williamrobinson4265

Жыл бұрын

common language needed in the title to bring people here but agree probably the most obvious learning opportunity that was missed here and a great place to start "youve been saying it wrong the whole time kids!" that will get them to watch the rest of the video

@sterlingroberts6240

Жыл бұрын

@@LRN2DIY please use your influence to help correct this then. Explain the correct term so people don’t make this mistake forever.

@fantasticsound2085

24 күн бұрын

​@@LRN2DIYDo not change what you said. This person's instructor was completely incorrect. Both situations are "stripped out". To "cam out" has nothing whatsoever to do with damage to the fastener or material. The short explanation: "Stripping out" material or a fastener is to remove material that engages a tool to the fastener or the fastener to the material. "Cam out" describes two components, intended to solidly move together when force is applied to one of the components, that slip because of an inability to retain proper position and alignment between the two. This can be by design or due to damage, but in the case of damage you haven't "cam'd out" the fastener or tool, you've stripped away material that creates a solid connection between them. In fact, if you completely strip the head of a cheap fastener, your tool won't cam out at all. It will simply spin in the empty space it drill out. The long explanation: By definition, "camming out" is when two objects that are designed to interact with force in one direction separate due to force in an off axis direction. Fasteners such as bolts, screws, etc are typically designed for clockwise force to apply or install the fastener and counterclockwise to loosen or remove the fastener. On a graph this would be equal force in both the x and y axis. Any force in the z-axis will either assist in preventing cam out or cause it. A perfect marriage of tool, fastener, and material can still experience cam out without damage to any of the components. In a ratchet, the operating mechanism is a deliberate cam out of the stationary tooth. It slides over the rotary gear teeth in one direction while catching in the opposite direction. "Stripping out" is absolutely caused by damage either to the fastener, the material, or the tool. To strip is to remove. In the case of materials, soft material or material that has become soft from rot or rust can be damaged by the threads of fastener, rounding out the entire hole to the outer diameter of the threads, thereby preventing them from securing the material. The threads of a fastener can be damaged and, consequently, also not engage the material to hold it in place. Stripping a fastener, as your entire video is about, is usually when a hardened or harder tool removes softer material from the head of the fastener. That isn't camming out! You've stripped The head of the fastener, removing material intended to engage the tool to the fastener. The slip is cam out. The damage that caused it is stripping out.

Legend, great tips👏

Thanks a lot for this good video

Very interesting, I have never heard of liquid grip, will look out for it next time in shop, seems like a handy thing to have.

Thanks for this. Good video.

Hey just an fyi but the first part you may want to ch do out the difference between Philips tip vs Reed Prince. Different tip looks almost the same slight different thickness but also sharp tip vs blunted tip. Also tapping in a tip with a hammer to clean any rust or dirt and fit better helps. I use the replaceable tips for that. Don’t want to hammer on my screwdrivers. Auto Tech.

I've watched a lot of KZread, and I've never instantly wanted the sponsor's product like I did after watching this video! 10/10 product placement 😅

This video is awesome thank you so much for this video. I learnt so much from it. I had no idea there is a difference between Philips and the Pozidriv. Blew my mind. Next up - I'll watch your video about the 5 drill features (I don't know that one either).

Fantastic video!

I bought a product like that nearly 20 years ago from Sears, it was a paste with tiny carbide grit in it, and it works well. I also bought screwdrivers that have grit made on the bit, they also work very well.

I wished I watched that like 20 years ago, thank you man 👍

Never knew liquid grip existed 😮Jolly good video

Tank bond liquid grip is new to me ... I'm bout to order it

@lawrencedavidson6195

2 жыл бұрын

Me too.

@bruceloy3756

2 жыл бұрын

It worked for me on 3 screws. They did not want to leave home.

Thanks for sharing great advices greetings from Maryland USA you're awesome

This is excellent.

The DAP Tank Bond Liquid Grip was worth the price of admission! Didn't know about it.

Thank you

Lowes first thing in the morning for Tank Liquid Bind Grip …thanks for the tips, great tutorial. /Bklyn👑

Excelente información, muy buen detalle y práctico.

Nice. Love that Tank Bond

A long time ago I switched over to hex head screws because stripped screw heads were too frequent. & used the 1/4 inch nut-setter that usually came with the drill or anything you bought for it.

Thank you for that tip. I am getting some DAP. I am learning a lot from your videos.

@vashon100

Жыл бұрын

DAP is the company, not the product.

Love that tank grip stuff i never seen that imma get me some that thank you

A few tips too... Those black screws are hardened steel. They are really hard to strip, so I use them a lot more, but even the standard screws that do strip, I find using one of those impact driver helps a LOT more than drills. I think the impact action keeps the head seated into the screw and unlike drills won't just back out.

@J.o.e_K

20 күн бұрын

as in drywall screws? If so the downside is they are brittle and not as strong as construction screws.

I've never heard of the tank bond. I'm ordering some right now

i was totally unaware of that liquid grip stuff too, good sponsor!

Thanks

Great tips for me: when on a ladder, using all of my 63 year old female upper body strenth, not easy to apply enough pressure! I like using Robertson screws.

@berniehayhurst1811

2 жыл бұрын

Robertson screws are the best by far, but not well known in the states.

@billwhite9333

2 жыл бұрын

Robertson = square head

@outlet6989

Жыл бұрын

For GOD's sake, what are you doing on a ladder? Don't you feel that you are too old to be doing DIY using a ladder? When I was just a young boy, my mother taught me not to climb any higher than I could afford to fall.

@dbeekman9738

Жыл бұрын

@@outlet6989 I'm 69 years old I worked off a ladder (not too high I admit) to remove 60 feet of rotted fascia board as the contractor wanted $1500 to replace it. Five hours to remove gutters and tear down by myself. Six hours the next day for me and a handyman to paint and install new 2x8 fascia. Total cost for materials and paying handyman $425.

@keithfaulkner6319

Жыл бұрын

@@berniehayhurst1811 sure they are! Just called square drive here. Menards sells lots of them. Not Home Depot though. Don't know about Lowes.

Thanks!

Thanks so much

I've gone over to star head screws. Wind them in fast with my cordless impact wrench and rarely need pilot holes in soft woods.

I am Canadian and I use Robertson screws. When I come across a Phillips, Which is often as the US has never heard of a Robertson, I replace it.

great video thank you What is the manual screwdriver at 4:25 in section 3 please?

Drill- Packedge in typical box, came with a tool bag (added bonus), two batteries, one charger, drill, and driver. Two words "plenty of Torque" kzread.infoUgkxW1vOBRCMrgTCDEijzpVzDWsgI-Jm2iQv well I guess that's three. Nice upgrade from current setup. Has belt clips, I don't think I will be using those. Driver and drill were bigger than what I expected but it is an upgrade from the current setup. For the money I would say that this is a great setup for Professionals and DIY/Weekend warriors.

thanks 👍

Great video as always but Tank Bond is incredibly expensive in UK $25! Love your stuff, Nils.

It's basically lapping compound, which along with its intended use, I've been using it for this purpose for years.

Great video, thanks so much really does help and correct the things I have been doing wrong. I am not a DIY guy, so this really does me 😁🤣😅

Good advise

Nice video. Thanks.

Good tips for a beginner.

Cool thank you!

Thanks 🙏

Thank you. i just stripped 3 screws which was incredibly frustrating. I can't get my drill to be at exactly the perfect angle because the Z bracket I'm mounting is in the way. I didn't realize the driver heads have sizes on them or that the place where you buy screws tells the driver size. Our package of driver heads that have been in our drill case for years are all the same size as the one that came attached to the drill (ph2). I didn't realize it until just now. I replaced the old one with one of the ones we've never used. I also dug through our very disorganized shelf of tools and found a set of assorted sizes which has a fatter, better fitting head, an extension to help with the angle problem, and I just ordered some tank bond on amazon. When the tank bond gets here tomorrow, those screws won't stand a chance! Thanks for making this vid.

I would start with the fact that absolutely any drive can cam out, depending on the conditions. Thank you for the liquid grip idea, I did not know such a product.

@tonybucca5667

11 ай бұрын

use a rubber band on top of the screw, or better yet, DITCH the philips

Still more: for decorative screws pre-drill and pre-thread the hole (using similar size strong screw).

This was a great ad!

شكرًا

That's really helpful tips, after 30 years or so doing DIY with an electric drill driver I now know why I've been going wrong after all this time, thank you :-)

Tanks

It took me years to finally come find this information

Some advice I learned hard way, I was using wrong size bit thinking it was correct size but just poorly fitting. Example, the T25 and T27 are very close and can think the T25 is proper for the bolt even with a little wiggle room, but putting the next size up [T27] was totally perfect fit and no more slippage or rounding of fitting Tank bond looks awesome

Nice video. do you have a video on how to make the right size pilot hole?

I find the pozidrive no 2 will fit most pozi screws. However the Dewalt no 2 pozi i find a bit small. Torx are excellent as long as you use the RIGHT SIZE. Obvious i would have thought!

I'll have to try out Tank Bond myself.

Yup, proper bit, been grinding some of them.

Man! - That LAST tip... Tank Bond Liquid Grip... I had no idea something like that existed. I subbed just because of that. Was stripping screws all day today it seemed. Up on a ladder, weird angles, sometimes where I had to use the non-dominant hand; and couldn't get my full body weight behind it. Wood felt rock hard. So, here's three tips of mine: 1) Whenever you have to press hard, tuck your elbow into your thigh or stomach; and don't wing out your elbow; but keep it very straight up and down. (This lines up your bones and muscles and everything with the best body mechanics for the best leverage). 2) Drill Pilot Holes, bigger ones for the part of the screw that's passing THROUGH THE OUTER MATERIAL; and smaller ones for the main connective piece. 2a) You can get jigs that keep you absolutely straight (meaning the holes wind being drilled at the exact same angle and the exact same distance from the end of the piece of wood, EVERY TIME, even when drilling at an angle, such as when attaching two pieces of wood that are perpendicular to one another. Good video all around. Thanks. DM

I've also heard that most of the cheap no-name Philips bits are not designed for impact driving. The Big Name bits with the color tape on the neck are the ones to use. Thanks for the tip on Tank Bond. Ordered sometoday.

@AllanO808

Жыл бұрын

That's why you purchase impact bits for the impact driver. Or regular bits for a non impact tool.

I am in Canada, where we mostly use the square Robertson. I have never had a problem with those, yet many people refused to use them. What are your thoughts on this?

@Lionofjuda957

Жыл бұрын

Hi Ontario here......yes we have the best,

@keithfaulkner6319

Жыл бұрын

I'm in USA we call them square drive and i totally agree they're the best.

That Dap product looks great. I'm wondering if one could apply it to the bit and get similar results?

Thank you very much for the tip (Tank bond), I've had several TBI's and 3 strokes. Very limited use of my right side body. This is going to be a life changer for me. Thank you again

Excellent video. If only people knew eh !! Things like this should be taught in schools so that when they venture out into the real world they'd stand half a chance. I was lucky that my Dad was an aviation prototype designer and engineer. By the age of 12 I was rebuilding old British seized up motorcycles, working on our privately owned biplanes, and I was flying them too. I'm a Husband and Wife team in property renovation. Screws, and nail, and my wife, don't get on well. I've showd her this video, much to her feeling insulted, but, hopefully, something might just 'click'. I'll know soon enough if the rate of problematic screws goes down !!! Videos like this seem ridiculous sometimes, but in reality, they really do have a 'once known - always remembered' . . . hopefully !!!! We need more videos like this type so thanks for that

@samhain9394

Жыл бұрын

1st grader attempt at "Humble Brag" has entered the chat.

Maybe I missed it, but pre-drilling the hole is probably the best tip I would give, especially on any sort of hard wood. It has the added bonus of preventing the wood from splitting / cracking.

Does the tank bond dry up and fill the slot making it almost impossible to extract as easily..