Got sick and tired of reading reddit posts. THANK YOU for this video. At least it's clear and i have visual examples.

@IPrint3dMinis

10 ай бұрын

Love it, yeah AA settings are a bit of hit or miss, and the chatter online is a bit off too. My current settings are sticking with the Smooth Surfaces, 50% offset, and 2 px radius. Works great now, barely see layer lines if at all.

Thanks for this information on a subject that can be very confusing (well, to me anyway). These videos you are producing on Lychee are great and helping lower the learning curve for this fantastic software. Please give us more.😎😎😎😎

@IPrint3dMinis

Жыл бұрын

You got it, working on more videos!

Super helpful, thanks!

@IPrint3dMinis

7 ай бұрын

Glad it helps!

Thanks for the 35 micron threshold. Been using it, and with my printer I'm well below that number with my printer. Looking forward to watching all the videos on this.

@IPrint3dMinis

6 ай бұрын

Glad to help

Very helpful information! Thank you! 1. What kind of anti-aliasing would you recommend for gaming miniatures? 2. Finally, how would you compare AA in Lychee to Chitubox?

@IPrint3dMinis

Жыл бұрын

I will do some compare with Chitu soon, I am working on some videos for Chitubox content as well and I will explain my thoughts on that when I do some more research personally as I use Lychee a lot more than Chitu. As far as AA for minis, like 32-55 mm I would recommend Sharpen Details, 20-30% grey offset, this will allow them to look sharp, and it should remove layer lines mostly or partially on flat areas or larger surface areas. If they are 75mm I would go to Smooth Surfaces, 2px radius 30% grey. I use that setting for my 75mm - 120mm stuff. Anything bigger than that go with Smooth Surfaces 1-2 px radius (depends on layer height) and 30-50% grey. Don't worry about detail loss, it will look really nice at that level, but this would be fo BIG objects like anything over 120mm.

Hey mate. When you mention not applying anti-aliasing to supports, does this mean that if I'm using a pre-supported .stl file, applying anti-aliasing to it WILL be applying it to the supports too? So essentially I'd have to use .lys pre-supported files to get around this?

@IPrint3dMinis

6 ай бұрын

Yes, if it is an STL and you use AA settings it technically will apply that to the STL and the supports. Using pre-supported STLs is usually a bad idea, we hate making them, but a lot of folks want them. We always provide LYS and STL files for this reason.

Thanks for that explanation, really helpful. Hope you don't mind me asking a question. I can see you print in a similar way as I do. What I have problem with the bottom flat surfaces when the plugs are. Like those legs in this video. In my case they are always deformed and look like a bar of soap. Do you have any suggestions how to minimize it? Thanks

@IPrint3dMinis

Жыл бұрын

No worries, it might be that the orientation is leading to warping issues. If the item is supposed to be square, make sure it starts at a corner, if it's cylindrical make sure and mimic the shape in supports or part of it will be pulling in different directions and cause warping. I hope that helps.

@androot69

Жыл бұрын

@@IPrint3dMinis Thank you for your reply. My objects are pretty much the same as yours. The bottom are where the split is is always deformed. I'll try rotating the object

@IPrint3dMinis

Жыл бұрын

@@androot69 Send me an email, send me a screen shot of how you are doing it. I would be happy to help. You can get my email from the about page.

thanks for info, can you test with Siraya Tech Fast resin?

@IPrint3dMinis

Жыл бұрын

Already have. AA settings work best with 4K and 8K resins. Standard resins do not really show much change when applied.

prints im doing that are around 5-8 cm big keep losing details on the faces and some areas im not sure how to fix it im suing a saturn 3 ultra

@IPrint3dMinis

5 ай бұрын

Orientation is a big way to fix that. Make sure no supports are touching the faces.

@clubskitzhardstyle

5 ай бұрын

@@IPrint3dMinis yeah i make sure none are now still is happening uncertain as to why

@IPrint3dMinis

5 ай бұрын

@@clubskitzhardstyle My suggestion then is to check that the supports are not too big. This might cause warping.

@clubskitzhardstyle

5 ай бұрын

@@IPrint3dMinis ive mainly been using the small auto supports still very new to this had it for around 2 weeks now

Can you upload in a higher resolution? The video resolution is so poor, I can't read anything you are pointing out.

@IPrint3dMinis

Жыл бұрын

It just uploaded, it's in 1080P, if you wait a few it will finish processing the HD version. Thanks!

@NoctuaStrigiformes

Жыл бұрын

@@IPrint3dMinis Thank you!

@IPrint3dMinis

Жыл бұрын

@@NoctuaStrigiformes Thanks for watching!

@NoctuaStrigiformes

Жыл бұрын

@@IPrint3dMinis Thank you for generating awesome content! I can't wait to see your channel grow!

@IPrint3dMinis

Жыл бұрын

@@NoctuaStrigiformes Thanks, we have a follow-up on this coming out tonight.

Seems like a good video with some helpful information but please please upgrade your audio setup. This was incredibly hard to listen to.

@IPrint3dMinis

2 ай бұрын

Sorry about that, upgraded the mic and stuff we are much better now.

@TriforceLegend64

2 ай бұрын

@@IPrint3dMinisawesome glad to hear it! As a content creator myself I know it’s a journey. Appreciate the good stuff you’re putting out.

@IPrint3dMinis

2 ай бұрын

@@TriforceLegend64 Appreciate the feedback.

Good video! Only two things I would change: voice audio was a bit too quiet, and more importantly - gif is not a brand of peanut butter, don't be a communist, give it a hard 'g'. I look forward to watching the comparison video.

@IPrint3dMinis

16 күн бұрын

Ha ha the GIF JIF argument is classic. I am not trying to be a communist. Why is it that big of an issue to use the soft G anyway, it is used with other words. I don't get it. Anyway the follow-ups are done, I have covered the AA settings a few times, but most recent videos this year I showed the end results. Also I have a new mic since this vid, so my audio is massively improved, and I removed the music.

Immediately closing video after hearing JIF

@IPrint3dMinis

Жыл бұрын

The what now?

To everyone with the "JIF" comment. Please read up on the actual facts folks. It's how you are supposed to say it. Steve Wilhite releases the Graphics Interchange Format, or GIF, while working for Compuserve. He called it a GIF with a soft g. “Choosy developers,“ he reportedly said, “choose JIF.” This was of course a play on the peanut butter brand Jif's line “choosy mothers choose Jif.” It was literally a play on the PB branding, and is pronounced with a soft "G" sorry folks.

@TriforceLegend64

2 ай бұрын

You’re of course right about the history, but I wouldn’t dig in too hard. Hard G is the much more common/accepted pronunciation. It’s also more correct when analyzed from a linguistics perspective. Sticking to the soft G on the “word of god” logic is a bit silly in 2024.

@IPrint3dMinis

2 ай бұрын

@@TriforceLegend64 I guess, but who cares how you really say it. For years i said "GIF" hard G, and then I was educated by a boss I had when I did IT, and he said it was "GIF" with the soft G sound or a J like sound, which is still correct, as the soft G is acceptable in the English language. Linguistics would say a soft G is fine, as in words like Gym, Georgia, George, Geode, and others, so I don't try and DIG too hard, but when I get comments saying they stopped watching after hearing I pronounce a word "correctly" it bothers me a bit. It's not the word of God, it's just facts. GIF is pronounced "J I F" whether or not it is the accepted way of saying or not is actually irrelevant. Again you wanna say it one way or the other fine, but to judge me on it...okay I guess. Gotta love the internet.

@LakusPakus

Күн бұрын

Who actually gives a shit. The soft G doesnt even work in my language. So its GIF for me.

@IPrint3dMinis

Күн бұрын

@@LakusPakus Apparently it was a bigger deal than I first thought. What language? Just curious. This conversion about GIF Vs. JIF honestly was not really the point of the video, and I am sorry that I even said the word now. This was published 10 months ago, and I still get comments about the GIF/JIF thing. So, crazy how much people take stake in something that doesn't really matter that much. I think I lost a sub or two due to this, and honestly if you are here for the way I speak...I figured folks come for the content not my style of speech.

@LakusPakus

Күн бұрын

@@IPrint3dMinis nah you’re good it’s just that the GIF/JIF debate is never ending. Pretty much a meme at this point. In Norwegian there’s no word that gives G any other sound than the hard one and the word for graphics is “grafikk”. This places us firmly on the side of GIF in the forever-war. Which means everyone else are wrong.

You 💯 had my attention until you said “jif”. 😨😔

@IPrint3dMinis

10 ай бұрын

It's how you say it. The dude who made literally was making a pun about the peanut butter tag line.

you could have explained just the settings in 2 minutes

@IPrint3dMinis

2 ай бұрын

Doubt it mate, have done like 7 videos on this topic, and it is still the most elusive setting in the application. Do you fully understand how it works on all printers and resin types? Cause we are still figuring it out, that's what the videos are for.