4:25 At this point I think you could just give him a normal sized knife xD Great Work!

@MrCampbellPrints

Ай бұрын

Lol, I was thinking the same, I did try, but handles on the ones I had were either too small or too large

Now thats the real t23

@MrCampbellPrints

Ай бұрын

Thanks

What 3d printer did you use? Please I need it my 3d printer is broken so I’m trying to replace it.

@MrCampbellPrints

9 күн бұрын

Bambulab p1s

Amazing video

@MrCampbellPrints

Ай бұрын

Glad you think so!

Cool, made one in 600%, largest ive seen online was 1337%

@MrCampbellPrints

Ай бұрын

Looks like I have to beat 1337%

I just did one at 200% and had 4 pieces to break. The Frame chest female connector broke while trying to add the head, and 3 of the knee elbow connectors broke while trying to connect one of the knees. The parts that broke were all printed using PETG. I used Glow in the dark PLA for the armor bits. I will use my heat gun on the replacement parts. Thanks for the advice. Cheers!

@MrCampbellPrints

5 күн бұрын

No worries let me know how it goes

@wickedPrints3256

5 күн бұрын

@@MrCampbellPrints Went great! I overheated one of the leg connections and it was a bit too loose. I just popped it off and reheated it. Closed it up a bit and it stiffened right up. Thanks again!

I was gonna make a big t13, BUT NOT THAT BIG

@MrCampbellPrints

Ай бұрын

Like they say go big or go 750% lol

@ChanceNittiReel

Ай бұрын

@@MrCampbellPrints lol

Good vid man you have a new subscriber!

@MrCampbellPrints

Ай бұрын

Thank you so much

Nice.

@MrCampbellPrints

Ай бұрын

Thank you! Cheers!

Man i gotta print this !!! How many rolls of filament did it take ??

@MrCampbellPrints

Ай бұрын

Only 2.5 rolls

Would love to see one life size, whatever scale to make it about 6 feet tall.... probably about 1200% since its normally about 6 inches.

@MrCampbellPrints

Ай бұрын

🫡

You should have yoused tree supports would have saved some time money and work . (Unless you’re already using tree supports) and what infill% did you use

@MrCampbellPrints

28 күн бұрын

I used 10% infill, I tried tree supports, but I found the quality of the print was better with just standard support

Do a video of all little dummy vs the 750%

@MrCampbellPrints

25 күн бұрын

I see you're a fan of the underdog, lol

Wow. If you go any bigger, it's probably worth printing the top of a ball as a seperate part to screw into the bottom?

@MrCampbellPrints

Ай бұрын

Good idea

Now that is a n13 titan if I say to my self and I like how it's big I never saw one maybe you can make a another one and have a stop motion fight just saying for idea

@MrCampbellPrints

5 күн бұрын

It's not a bad idea, but it's so big and heavy that the limbs don't stay in place, but it is probably down to me just down to me sanding down parts to fit. Thank you for the support

My thumbs are so sore after assembling this at 100% percent scale! And the legs aren't even done!

@MrCampbellPrints

5 күн бұрын

Once you do a few, you get used to it and fet those 3d printed muscles pumping. Lol, thanks for the support

@jurassicanimation1518

5 күн бұрын

I do also think because I wasn't using PETG for the frame instead I used PLA lol. Still going well though.

you need to rotate it 180 angle

@MrCampbellPrints

Ай бұрын

Are you referring to the armor

❤❤❤❤👍👍👍👍 классный

@MrCampbellPrints

Ай бұрын

Thank you

How do you deal with the loose joints after a while

@MrCampbellPrints

Ай бұрын

You can add a thin lay of Super glue or equivalent and let it dry and keep adding layers

@k4rz3n

Ай бұрын

@@MrCampbellPrints thanks for the tip🔥

@wcbyrdiv

Ай бұрын

If you use super glue, you have to either disassemble it before applying the glue, or apply it to the joint and keep wiggling the joint until it is completely dry, which takes longer than you think. The better solution is pledge floor wax. You just drop a few drops into the joint while it is still assembled. wiggle the joint to spread it and then let it sit for about 2-3 hours to dry. If its still loose, apply again. Because its not adhesive, you never have to worry about the joint seizing up.... Old trick learned from the Star Wars figures back in the 70's.....

@k4rz3n

Ай бұрын

@@wcbyrdiv Very helpful 🤝🔥

Im trying to print The Dummy 13 action figure using the Cura software with my Ender 3 v3 se, But the parts especially the crotch doesn't seem to fit. If anyone knows the Ultimaker Cura Settings for the print in specific detail, please give me an answer. I Don't wanna waste anymore filament. i wanna scale it to 300% IDK what im doing wrong! why isn't this working for me?

@MrCampbellPrints

Ай бұрын

I use the same settings that I printed this size dummy 13 on the 150% and 400% scale that I have printed mabey them

@Pugwash.

Ай бұрын

Have a play with the Horizontal Expansion. I used -0.1mm when I printed at 173%

Where can I buy one?

@MrCampbellPrints

Ай бұрын

mrcampbellprints.etsy.com/listing/1692155915

you did put the abdomen on the wrong side

@MrCampbellPrints

Ай бұрын

I'm not sure I did

Attack on titan but t13 figs

@MrCampbellPrints

Ай бұрын

😆

@Breen0

Ай бұрын

@@MrCampbellPrints i subbed to your channel

DO 1000%

@MrCampbellPrints

24 күн бұрын

I want to go bigger

@iDrawforfun12345

24 күн бұрын

Yeahhhhhhh that's SICK tho

If you did a 1000% you woud have no room in your house

@MrCampbellPrints

Ай бұрын

Mabey I'll make a bigger one.......

Can you print me one?

@MrCampbellPrints

Ай бұрын

😅

Hi 😅

@MrCampbellPrints

Ай бұрын

Hey there

@sebastianroque1493

Ай бұрын

How are you?

@sebastianroque1493

6 күн бұрын

Fbr5*afwrdsgsfst*wr

sticky bot are beter

@MrCampbellPrints

Ай бұрын

😅

@321_let_rip

14 күн бұрын

Nah bruh I printed one to see for my self and the print is so good

Can you print me one?

@MrCampbellPrints

Ай бұрын

😇

@sebastianroque1493

Ай бұрын

Yes, or no

@sebastianroque1493

Ай бұрын

Please

@sebastianroque1493

Ай бұрын

Please