Thanks sir for your great job I have learned a lot in this video,you clearly explain the difference between the pull up and pull down

Hello, niece explained. This type of training is needed. Keep up the good work.

@RodriguezRepairs

Жыл бұрын

Thank you so much 🙂

Great video!! glad I found your channel, and hope there is more to come!!

@RodriguezRepairs

2 жыл бұрын

thank you! i really appreciate it!

Many thanks!!! Helped me a lot!

Thank you. This helped me so much!! 🙏

@RodriguezRepairs

4 ай бұрын

No problem! Thank you for the subscription!

Great job.

Simply wow presentation 👌👌👌❤

Thank you sir

Hii,great video, can you please assist I have a chevy spark with no pulse on injectors, voltage at crank sensor is 1.88v ,can this be right or too low

So if I put a jumper wire between the 5 volt reference wire and the signal wire will it fool the computer to think everything's fine and get my check engine light off so I can pass smog?

The Pull-up doesn't always have the resistor. What's important to know is the voltage level on the signal wire is when it is unplugged from the sensor; be it is high or low. If the signal is high unplugged the sensor is Pull-Down design. If the signal is low unplugged the sensor is a pull=up.

@RodriguezRepairs

Жыл бұрын

I agree 100%

@charmanrecordings1186

9 ай бұрын

And what voltage is considered “low” or “high” I have a vw polo 1.4 16v and the signal cable when unplugged from the sensor has around 4,8 volts.

@ALEFILES

7 ай бұрын

​​@@RodriguezRepairsThanks for the video! So the A3144 hall effect sensor is pull DOWN sensor? I didn't realize that there are pull UP sensors (Hall effect sensors that use pull DOWN resistor)...¿Do you know some model of pull up sensor? Thanks a lot! Greetings from Argentina!

This is an excellent explanation! What could be the typical value of these pull-up and pull-down resistor?

@RodriguezRepairs

2 жыл бұрын

Thank you!! I believe the typical value for these resistors can range around the10k area

Hi, great video! One littel question. My escooters have a throttle with a hall sensor inside. How can he know how fast i want to drive? I think he would have to give full throttle at 5v and then no trottle at 0V, but how can he differentiate so precisely? A mystery for me 🤔🤔☺

hi theanks for video, have you done a video on how to tell if you have a pull down or push up sensors? thanks

@RodriguezRepairs

4 ай бұрын

I'm glad you found this video useful! I will do a video like that soon!

Hy, i have a question, can you tell me how can i connect a loudspeaker digital volume control to a hall sensor (from finger throttle's ebike ) in order to be able to control volume. Thank you in advance for your answer

@RodriguezRepairs

2 жыл бұрын

So you want to control volume from your fingers throttle? In on and off patterns?

@georgesoare7937

2 жыл бұрын

@@RodriguezRepairs yes. i want to control loudspeaker volume with hall sensor from finger throttle, but not only on and off.... i want to increase and decrease volume accordind to tension variation from hall sensor

@georgesoare7937

2 жыл бұрын

this is the loudspeaker : kzread.info/dash/bejne/rKBtxamYlrnfnrA.html

@georgesoare7937

2 жыл бұрын

and i want to connect the 3 pins of the hall sensor to the USB from finger throttle.... and the digital volume in a USB mother connector, in order to use a small USB cable for connection between toudspeaker and finger throttle's USB

@georgesoare7937

2 жыл бұрын

and this is the finger throttle: bmsbattery.com/home/1132-lcd-tf100-display-with-throttle.html

I don’t understand? Hall sensor will output 0-5 volts based on magnetic field regardless of an external resistor. There must be another purpose for the pull up or pull down? Noise interference perhaps?

@embeddedtechnologies9425

Жыл бұрын

He is explaining, open drain, without knowing it. if he really know, then please send me the Part no, of the hall sensor.

????? pull UP should have resistor to +5V, pullDOWN should have resistor to GROUND.

There is no such thing as a pullup or a pulldown resistor. The resistor has an ohm value. Where the resistor is placed in the circuit determines the name of the circuit. kzread.info/dash/bejne/mnyHtK6fiKW0Z9Y.htmlsi=F5hCbRL6m4g43CKU

your conflicting information doesnt help

Thank you sir

@RodriguezRepairs

Жыл бұрын

No problem! Im glad you found the the video useful!